VLAN的混杂模式小实验

混杂模式实验

1、拓扑图

2、划分各个交换机的VLAN

lsw1：
[lsw1]vlan batch 2 3
Info: This operation may take a few seconds. Please wait for a moment...done
lsw2：
[Huawei]vlan batch 2 4
Info: This operation may take a few seconds. Please wait for a moment...done.
lsw3：
[Huawei]vlan batch 2 5
Info: This operation may take a few seconds. Please wait for a moment...done.

3、各个接口划入VLAN

LSW1:

[lsw1-GigabitEthernet0/0/1]port hybrid untagged vlan 2 to 5————U设置为VLAN 2—5
[lsw1-GigabitEthernet0/0/1]port hybrid tagged vlan 2————————T设置为VLAN 2


[lsw1-GigabitEthernet0/0/2]port link-type access ——————接口设置为access接口
[lsw1-GigabitEthernet0/0/2]port default vlan 2————————划分区域为VLAN 2

[lsw1-GigabitEthernet0/0/3]port hybrid pvid vlan 3——PVID设置为VLAN 3
[lsw1-GigabitEthernet0/0/3]port hybrid untagged vlan 3 to 5———— 添加允许列表3、4、5,同时定义其字母为U
  
  
[lsw1-GigabitEthernet0/0/4]port link-type trunk ——接口设置为trunk接口
[lsw1-GigabitEthernet0/0/4]port trunk allow-pass vlan 2 to 5——接口trunk允许通过VLAN 2-5

LSW2:

[lsw2-GigabitEthernet0/0/1]port link-type trunk
[lsw2-GigabitEthernet0/0/1]port trunk allow-pass vlan 2 to 5


[lsw2-GigabitEthernet0/0/3]port hybrid pvid vlan 4
[lsw2-GigabitEthernet0/0/3]port hybrid untagged vlan 2 to 4

[lsw2-GigabitEthernet0/0/2]port link-type access 
[lsw2-GigabitEthernet0/0/2]port default vlan 2

[lsw2-GigabitEthernet0/0/4]port link-type trunk 
[lsw2-port-group-trunk]port trunk allow-pass vlan 2 to 5

LSW3:

[Huawei-GigabitEthernet0/0/1]port link-type trunk
[Huawei-GigabitEthernet0/0/1]port trunk allow-pass vlan 2 to 5


[Huawei-GigabitEthernet0/0/3]port hybrid pvid vlan 5
[Huawei-GigabitEthernet0/0/3]port hybrid untagged vlan 3 to 5

[Huawei-GigabitEthernet0/0/2]port hybrid pvid vlan 4
[Huawei-GigabitEthernet0/0/2]port hybrid untagged vlan 3 to 4

4、在路由器开启DHCP操作

1、创建子接口

[Huawei]interface g0/0/0.1
[Huawei-GigabitEthernet0/0/0.1]dot1q termination vid 2——子接口可以处理vlan 2的流量
[Huawei-GigabitEthernet0/0/0.1]ip addressip address 192.168.1.10 24——为子接口配置一个IP地址
[Huawei-GigabitEthernet0/0/0.1]arp broadcast enable——子接口开启ARP广播功能

[Huawei]interface g0/0/0.2
[Huawei-GigabitEthernet0/0/0.2]dot1q termination vid 3
[Huawei-GigabitEthernet0/0/0.2]ip address 192.168.2.10 24
[Huawei-GigabitEthernet0/0/0.2]arp broadcast enable 

2、开启DHCP

[Huawei]ip pool a
Info: It's successful to create an IP address pool.
[Huawei-ip-pool-a]gateway-list 192.168.1.10
[Huawei-ip-pool-a]network 192.168.1.0 mask 24	
[Huawei-ip-pool-a]dns-list 114.114.114.114
[Huawei-ip-pool-a]q

[Huawei]ip pool b
[Huawei-ip-pool-b]gateway-list 192.168.2.10
[Huawei-ip-pool-b]network 192.168.2.0 mask 24 	
[Huawei-ip-pool-b]dns-list 114.114.114.114
[Huawei-ip-pool-b]q

3、接口开启DHCP

[Huawei-GigabitEthernet0/0/0]dh	
[Huawei-GigabitEthernet0/0/0]dhcp s	
[Huawei-GigabitEthernet0/0/0]dhcp select g	
[Huawei-GigabitEthernet0/0/0]dhcp select global 
[Huawei-GigabitEthernet0/0/0]int g0/0/0.1
[Huawei-GigabitEthernet0/0/0.1]dhcp select global
[Huawei-GigabitEthernet0/0/0.1]q

4、PC端开启dhcp

5、检测（略）