看到很多朋友对GRBL挺感兴趣,网上关于stm32移植GRBL的例子确实也不多,而且收到很多朋友询问工程源码,在这里统一回复下
由于GRBL是当初实习项目需要,把GRBL做成PLC指令放在PLC系统中的,所以GRBL自然就是系统中的一小部分功能,现在实习结束,就没有当初的源码工程了,而且这个也是公司不允许的,我网上贴出来的代码都是当初自己测试GRBL时候写的测试代码,全部测试通过的。
今天详细看了一下,硬件部分的代码:IO、串口、定时器控制都已经贴出
上层代码像:gcode.c motion_control.c planner.c protocol.c spindle_control.c 基本未做修改,因为这部分是上层代码,与底层硬件无关,直接借用就好
还有朋友问道关于限位开关的地方,这个是在支持文件中的limits.c中写的,如果需要限位功能,需要修改此文件中关于读取限位开关IO引脚的配置,我当初项目中未使用到限位,所以我在下面主函数调用中屏蔽掉了关于限位的代码limits_init();
关于protocol.c spindle_control.c主要是来做主轴控制的,像主刀或者喷胶之类的,这个我们只用GRBL做了个双轴差补,所以这些功能也都没实现,所以在下面主函数中屏蔽了这些功能的初始化://protocol_init(); // Clear incoming line data and execute startup lines
//spindle_init();
//coolant_init();
下面是主函数的调用,希望可以帮助到大家,仍有疑问请评论,看到尽量回复
main.c
#include <stm32f10x_lib.h>
#include "stdio.h"
#include "config.h"
#include "planner.h"
#include "nuts_bolts.h"
#include "stepper.h"
#include "spindle_control.h"
#include "coolant_control.h"
#include "motion_control.h"
#include "gcode.h"
#include "protocol.h"
#include "limits.h"
#include "report.h"
#include "settings.h"
#include "serial.h"
#include "print.h"
#include "sys.h"
//printf
#ifdef __GNUC__
/* With GCC/RAISONANCE, small printf (option LD Linker->Libraries->Small printf
set to 'Yes') calls __io_putchar() */
#define PUTCHAR_PROTOTYPE int __io_putchar(int ch)
#else
#define PUTCHAR_PROTOTYPE int fputc(int ch, FILE *f)
#endif /* __GNUC__ */
// Declare system global variable structure
system_t sys;
void sei(void)
{
//bit0=1¿ªÆô¶¨Ê±Æ÷£¬bit6,5=00±ßÑØ,bit4=0ÏòÉϼÆÊý 1ÏòÏ£¬bit9,8=00ÎÞ·ÖƵ 01=2* 10=4*
TIM3->CR1|=0X01;
//bit0=1¿ªÆô¶¨Ê±Æ÷£¬bit6,5=00±ßÑØ,bit4=0ÏòÉϼÆÊý 1ÏòÏ£¬bit9,8=00ÎÞ·ÖƵ 01=2* 10=4*
TIM4->CR1|=0X01;
}
void cli(void)
{
//bit0=1¹Ø±Õ¶¨Ê±Æ÷
TIM3->CR1&=~0X01;
//bit0=1¹Ø±Õ¶¨Ê±Æ÷
TIM4->CR1&=~0X01;
}
int main(void)
{
// Initialize system
Stm32_Clock_Init(9); //ʱÖÓ72M //APB1¶þ·ÖƵ£¬APB2²»·ÖƵ
//serial_init(); // Setup serial baud rate and interrupts
USART_Configuration();
settings_init(); // Load grbl settings from EEPROM
st_init(); // Setup stepper pins and interrupt timers
sei(); // Enable interrupts //¿ªÈ«¾ÖÖжϣ¬cli()¹ØÈ«¾ÖÖжÏ
memset(&sys, 0, sizeof(sys)); // Clear all system variables
sys.abort = true; // Set abort to complete initialization
sys.state = STATE_INIT; // Set alarm state to indicate unknown initial position
printPgmString("for(;;)\r\n");
for(;;) {
// Execute system reset upon a system abort, where the main program will return to this loop.
// Once here, it is safe to re-initialize the system. At startup, the system will automatically
// reset to finish the initialization process.
if (sys.abort) {
// Reset system.
serial_reset_read_buffer(); // Clear serial read buffer
plan_init(); // Clear block buffer and planner variables
gc_init(); // Set g-code parser to default state
//protocol_init(); // Clear incoming line data and execute startup lines
//spindle_init();
//coolant_init();
//limits_init();
st_reset(); // Clear stepper subsystem variables.
// Sync cleared gcode and planner positions to current system position, which is only
// cleared upon startup, not a reset/abort.
sys_sync_current_position();
// Reset system variables.
sys.abort = false;
sys.execute = 0;
if (bit_istrue(settings.flags,BITFLAG_AUTO_START)) { sys.auto_start = true; }
// Check for power-up and set system alarm if homing is enabled to force homing cycle
// by setting Grbl's alarm state. Alarm locks out all g-code commands, including the
// startup scripts, but allows access to settings and internal commands. Only a homing
// cycle '$H' or kill alarm locks '$X' will disable the alarm.
// NOTE: The startup script will run after successful completion of the homing cycle, but
// not after disabling the alarm locks. Prevents motion startup blocks from crashing into
// things uncontrollably. Very bad.
#ifdef HOMING_INIT_LOCK
if (sys.state == STATE_INIT && bit_istrue(settings.flags,BITFLAG_HOMING_ENABLE)) { sys.state = STATE_ALARM; }
#endif
// Check for and report alarm state after a reset, error, or an initial power up.
if (sys.state == STATE_ALARM) {
report_feedback_message(MESSAGE_ALARM_LOCK);
} else {
// All systems go. Set system to ready and execute startup script.
sys.state = STATE_IDLE;
// protocol_execute_startup();
}
}
protocol_execute_runtime();
protocol_process(); // ... process the serial protocol
}
return 0; /* never reached */
}
//printf
/**
* @brief Retargets the C library printf function to the USART.
* @param None
* @retval None
*/
PUTCHAR_PROTOTYPE
{
/* Place your implementation of fputc here */
/* e.g. write a character to the USART */
USART_SendData(USART1, (uint8_t) ch);
/* Loop until the end of transmission */
while (USART_GetFlagStatus(USART1, USART_FLAG_TC) == RESET)
{}
return ch;
}