摘 要
某集团商务中心根据设计要求为六层混凝土框架结构,建筑高度为 23.2 米,建筑面积
为 5587.6 ㎡。
本设计主要包括建筑设计和结构设计两部分。建筑设计,包括平面定位图设计、平面设计、立面设计、剖面设计。结构设计,框架结构设计主要包括:结构选型,梁、柱、墙等构件尺寸的确定,重力荷载计算、横向水平作用下框架结构的内力和侧移计算、竖向荷载作用下横向框架的内力分析、内力组合、截面设计、基础设计。其中,基础设计又包括基础选型、基础平面布置、地基计算等。
在设计的过程中我严格按照最新规范及有关规定进行设计,其中采用的计算方法均参照有关书籍。
关键词:办公楼设计;框架结构;结构计算;
Abstract
Business center of a group of six according to the design requirements of concrete frame structure, building height of 23.2 meters, construction area of 5587.6 square meters.
The design includes architectural design and structural design of two parts. Architectural design, including flat-screen positioning map design, graphic design, facade design, profile design. Structural design, structural design of the framework include: structural selection, beams, columns, walls and other components to determine the size, gravity load calculation, transverse horizontal frame structure under the action of internal forces and drift calculations, the transverse vertical loads Frame Structure analysis, internal forces combined, cross-sectional design, basic design. Among them, the basic design also includes basic selection, basic layout, foundations calculation.
I am in the process of designing strict accordance with the relevant provisions of the latest specification and design, which is based on calculations taking into account relevant books.
Keywords: building design; frame structure; structure calculation;
目 录
1 绪 论 ..- | 1 | - |
1.1 题目背景 ........................................... - | 1 | - |
1.2 工程概况 ........................................... - | 1 | - |
1.3 设计内容与方法 ..................................... - | 1 | - |
2 建筑设计 ..- | 3 | - |
2.1 建筑的总平面设计................................... - | 3 | - |
2.2 建筑平面设计 ....................................... - | 3 | - |
3 结构设计 ..- | 5 | - |
3.1 结构方案设计 ....................................... - | 5 | - |
3.2 结构布置及计算简图 ................................. - | 5 | - |
3.3 重力荷载计算 ...................................... - | 7 | - |
3.4 屋面及楼面可变荷载标准值 ........................... - | 7 | - |
3.5 梁、柱、墙、窗、门重力荷载计算..................... - | 8 | - |
3.6 重力荷载代表值 ..................................... - | 8 | - |
3.7 横向框架侧移刚度计算 ............................... - | 9 | - |
-
- 横向水平地震作用下框架结构的内力和侧移计算 ....... - 10 -
- 横向风荷载作用下框架结构内力和侧移计算 15
- 竖向荷载作用下框架结构的内力计算 19
4.1.2.1 恒荷计算 19
1 绪 论
-
- 工程名称
本工程为某集团商务中心
-
- 工程概况
某集团商务中心, 建筑层数 6 层左右。建筑物底层设有设备间、供暖间、配电室、客房。二至六层设有若干标准客房等。建筑设计使用年限为50 年, 建筑安全等级为三级。建筑物需满足国家、地方有关规范要求。
框架填充墙结构, 楼盖及屋盖均采用现浇钢筋混凝土结构, 楼板厚度取 120mm。填充墙采用陶粒混凝土空心砌块。主体结构 6 层,底层层高 4.2m, 其余层高均为 3.6m。
外门为铝合金门, 内门为木门, 窗为铝合金窗。
材料选用: 框架柱均采用 C30 混凝土, 受力钢筋采用 HRB335 级钢筋。箍筋采用 HPB235 级钢筋。钢筋的连接优先采用焊接。
柱 网: 本建筑采用内廊式平面组合, 纵向柱距为分别为 7.8m,横
向跨度边跨跨度为 6.6m, 中间跨度为 2. 4m。
自然条件: 基本风压为 0.35 kN/ m2 , 基本雪压为 0.6kN/ m2 。
地质条件: 地面粗糙度为 C 类。建筑场地类别为二类场地, 抗震设防烈度为 7 度,地震分组为第一组。水平地震影响系数为 amax =0.08,Tg = 0.35 。根据工程地质勘测报告, 拟建场地地势平坦, 地质情况如下:
场区范围内土质构成, 自地表向下依次为:
a 层: 杂填土, 厚度 0. 7m, 地基承载力标准值 fk=80Kpa
b 层: 亚粘土, 厚度 0. 5- 1. 0m, 硬塑状地基承载力标准值 fk=150Kpa c 层: 粘土, 厚度 5- 7 m, 地基承载力标准值 fk=240Kpa
……