VLAN综合实验

一、实验拓扑

二、实验要求

1、pc1和pc3所在接口为access;属于vlan 2；

      pc2/pc4/pc5/pc6处于同一网段:其中pc2可以访问pc4/pc5/pc6，pc4可以访问pc6，pc5不能访问pc6；
2、pc1/pc3与pc2/pc4/pc5/pc6不在同一网段;
3、所有pc通过DHCP获取Ip地址，且pc1/pc3可以正常访问pc2/pc4/pc5/pc6;

三、实验步骤

1.创建vlan

对sw1：

[sw1]vlan batch 2 to 6
Info: This operation may take a few seconds. Please wait for a moment...done.

对sw2：

[sw2]vlan batch 2 to 6
Info: This operation may take a few seconds. Please wait for a moment...done.

对sw3：

[sw3]vlan batch 2 to 6
Info: This operation may take a few seconds. Please wait for a moment...done.

2.配置接口类型及增删vlan标签

对sw1：

[sw1]int g0/0/1

[sw1-GigabitEthernet0/0/1]port link-type access

[sw1-GigabitEthernet0/0/1]port default vlan 2

[sw1]int g 0/0/2

[sw1-GigabitEthernet0/0/2]port link-type hybrid

[sw1-GigabitEthernet0/0/2]port hybrid untagged vlan 3 to 6

[sw1-GigabitEthernet0/0/2]port hybrid pvid vlan 3

[sw1]int g 0/0/3

[sw1-GigabitEthernet0/0/3]port link-type trunk

[sw1-GigabitEthernet0/0/3]port trunk allow-pass vlan 2 to 6

[sw1]int g 0/0/4

[sw1-GigabitEthernet0/0/4]p l h

[sw1-GigabitEthernet0/0/4]p h u v 3 4 5 6

[sw1-GigabitEthernet0/0/4]port hybrid tagged vlan 2

对sw2：

[sw2]int g 0/0/1   

[sw2-GigabitEthernet0/0/1]port link-type access

[sw2-GigabitEthernet0/0/1]port default vlan 2

[sw2]int g 0/0/2

[sw2-GigabitEthernet0/0/2]p l h

[sw2-GigabitEthernet0/0/2]port hybrid pvid vlan 4

[sw2-GigabitEthernet0/0/2]port hybrid untagged vlan 3 to 6

[sw2]int g 0/0/3

[sw2-GigabitEthernet0/0/3]p l t

[sw2-GigabitEthernet0/0/3]p t a v 2 t 6

[sw2]int g 0/0/4

[sw2-GigabitEthernet0/0/4]p l t

[sw2-GigabitEthernet0/0/4]p t a v 2 t 6

对sw3：

[sw3]int g 0/0/1

[sw3-GigabitEthernet0/0/1]p l h

[sw3-GigabitEthernet0/0/1]p h p v 5

[sw3-GigabitEthernet0/0/1]p h u v 3 4 5

[sw3]int g 0/0/2

[sw3-GigabitEthernet0/0/2]p l h

[sw3-GigabitEthernet0/0/2]p h p v 6

[sw3-GigabitEthernet0/0/2]p h u v 3 4 6

[sw3]int g 0/0/3

[sw3-GigabitEthernet0/0/3]p l t

[sw3-GigabitEthernet0/0/3]p t a v

[sw3-GigabitEthernet0/0/3]p t a v 2 3 4 5 6

3.配置地址池

对R1配置IP地址，子接口2.0，物理口1.0:

[R1]int g 0/0/0

[R1-GigabitEthernet0/0/0]ip address 192.168.1.1 24

[R1-GigabitEthernet0/0/0]int g 0/0/0.1

[R1-GigabitEthernet0/0/0.1]ip address 192.168.2.1 24

[R1-GigabitEthernet0/0/0.1]dot1q termination vid 2

[R1-GigabitEthernet0/0/0.1]arp broadcast enable

配置DHCP，配置地址池及网关，进接口，全局下发

[R1]dhcp enable

[R1]ip pool aa

Info: It's successful to create an IP address pool.

[R1-ip-pool-aa]network 192.168.1.0 mask 24

[R1-ip-pool-aa]gateway-list 192.168.1.1 

[R1-ip-pool-aa]dns-list 114.114.114.114

[R1-ip-pool-aa]q

[R1]ip pool bb

Info: It's successful to create an IP address pool.

[R1-ip-pool-bb]network 192.168.2.0 mask 24

[R1-ip-pool-bb]gateway-list 192.168.2.1

[R1-ip-pool-bb]dns-list 114.114.114.114

4.查看ip获取：

5.测试