1、pc1和pc3所在接口为access；属于vlan 2；pc2/pc4/pc5/pc6处于同一网段:其中pc2可以访问pc4/pc5/pc6，pc4可以访问pc6，pc5不能访问pc6；2

一、实验拓扑

二、实验要求

1、pc1和pc3所在接口为access;属于vlan 2；

pc2/pc4/pc5/pc6处于同一网段:其中pc2可以访问pc4/pc5/pc6，pc4可以访问pc6，pc5不能访问pc6；

2、PC4pc1/pc3与pc2/pc4/pc5/pc6不在同一网段;

3、所有pc通过DHCP获取Ip地址，且pc1/pc3可以正常访问pc2/pc4/pc5/pc6;

三、实验思路

1. 先创建VLAN
2. 再配置接口类型及增删标签
3. 配置两个地址池

四、实验步骤

1. 先创建VLAN

sw1：

[sw1]vlan batch 2 to 6

Info: This operation may take a few seconds. Please wait for a moment...

sw2：

[sw2]vlan batch 2 to 6

Info: This operation may take a few seconds. Please wait for a moment...

sw3：

[sw3]vlan batch 2 to 6

Info: This operation may take a few seconds. Please wait for a moment..

2、  再配置接口类型及增删标签

sw1：

[sw1]int g0/0/1

[sw1-GigabitEthernet0/0/1]port link-type access

[sw1-GigabitEthernet0/0/1]port default vlan 2

[sw1]int g 0/0/2

[sw1-GigabitEthernet0/0/2]port link-type hybrid

[sw1-GigabitEthernet0/0/2]port hybrid untagged vlan 3 to 6

[sw1-GigabitEthernet0/0/2]port hybrid pvid vlan 3

[sw1]int g 0/0/3

[sw1-GigabitEthernet0/0/3]port link-type trunk

[sw1-GigabitEthernet0/0/3]port trunk allow-pass vlan 2 to 6

[sw1]int g 0/0/4

[sw1-GigabitEthernet0/0/4]p l h

[sw1-GigabitEthernet0/0/4]p h u v 3 4 5 6

[sw1-GigabitEthernet0/0/4]port hybrid tagged vlan 2

sw2：

[sw2]int g 0/0/1   

[sw2-GigabitEthernet0/0/1]port link-type access

[sw2-GigabitEthernet0/0/1]port default vlan 2

[sw2]int g 0/0/2

[sw2-GigabitEthernet0/0/2]p l h

[sw2-GigabitEthernet0/0/2]port hybrid pvid vlan 4

[sw2-GigabitEthernet0/0/2]port hybrid untagged vlan 3 to 6

[sw2]int g 0/0/3

[sw2-GigabitEthernet0/0/3]p l t

[sw2-GigabitEthernet0/0/3]p t a v 2 t 6

[sw2]int g 0/0/4

[sw2-GigabitEthernet0/0/4]p l t

[sw2-GigabitEthernet0/0/4]p t a v 2 t 6

sw3:

[sw3]int g 0/0/1

[sw3-GigabitEthernet0/0/1]p l h

[sw3-GigabitEthernet0/0/1]p h p v 5

[sw3-GigabitEthernet0/0/1]p h u v 3 4 5

[sw3]int g 0/0/2

[sw3-GigabitEthernet0/0/2]p l h

[sw3-GigabitEthernet0/0/2]p h p v 6

[sw3-GigabitEthernet0/0/2]p h u v 3 4 6

[sw3]int g 0/0/3

[sw3-GigabitEthernet0/0/3]p l t

[sw3-GigabitEthernet0/0/3]p t a v

      

[sw3-GigabitEthernet0/0/3]p t a v 2 3 4 5 6

3、  配置两个地址池

R1:

（1）：配置IP地址，子接口2.0，物理口1.0

[Huawei]sy R1

[R1]int g 0/0/0

[R1-GigabitEthernet0/0/0]ip address 192.168.1.1 24

[R1-GigabitEthernet0/0/0]int g 0/0/0.1

[R1-GigabitEthernet0/0/0.1]ip address 192.168.2.1 24

[R1-GigabitEthernet0/0/0.1]dot1q termination vid 2

[R1-GigabitEthernet0/0/0.1]arp broadcast enable

（2）：配置DHCP，配置地址池及网关，进接口，全局下发

[R1]dhcp enable

[R1]ip pool aa

Info: It's successful to create an IP address pool.

[R1-ip-pool-aa]network 192.168.1.0 mask 24

[R1-ip-pool-aa]gateway-list 192.168.1.1 

[R1-ip-pool-aa]dns-list 114.114.114.114

[R1-ip-pool-aa]q

[R1]ip pool bb

Info: It's successful to create an IP address pool.

[R1-ip-pool-bb]network 192.168.2.0 mask 24

[R1-ip-pool-bb]gateway-list 192.168.2.1

[R1-ip-pool-bb]dns-list 114.114.114.114

IP获取情况：

pc1pingpc2：

PC1pingPC3：

PC5pingPC6：