Arduino Uno添加点阵屏

（不想登录的去我的B站账号：せすさん）

首先介绍一下初学者对点阵屏的盲区与误解：

1.有的朋友认为：共阳就是LED正极全部接在一起，而负极则不是，共阴相反但也是类似，虽然数码管的共阳和共阴是这样的，但点阵8*8点阵共阴共阳其实都是接在一起的。 

 2. 所谓共阳和共阴只是管脚排列名称相同或者说无论共阳还是共阴管脚编号一 致，但行和列的极性则相反。既然这样，那么我反过方向接共阳不就是变成了共阴吗？理论上是的，但要注意行和列相交的位置发生了变化。

开始

注：本次实验使用Arduino 控制器直接驱动一个单色的8*8点阵，所用点阵型号为LD-1088BS 

这现将连接示意图摆在这：

复杂，但没办法，我只想弄来了这种不用驱动器的方法

 编辑！

 代码放这儿了，显示的是HELLO：

#include <FrequencyTimer2.h>
 //by mahiro
#define SPACE { \
    {0, 0, 0, 0, 0, 0, 0, 0},  \
    {0, 0, 0, 0, 0, 0, 0, 0}, \
    {0, 0, 0, 0, 0, 0, 0, 0}, \
    {0, 0, 0, 0, 0, 0, 0, 0}, \
    {0, 0, 0, 0, 0, 0, 0, 0}, \
    {0, 0, 0, 0, 0, 0, 0, 0}, \
    {0, 0, 0, 0, 0, 0, 0, 0}, \
    {0, 0, 0, 0, 0, 0, 0, 0} \
}
 
#define H { \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 1, 1, 1, 1, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}  \
}
 
#define E  { \
    {0, 1, 1, 1, 1, 1, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 1, 1, 1, 1, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 1, 1, 1, 1, 1, 0}  \
}
 
#define L { \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 0, 0}, \
    {0, 1, 1, 1, 1, 1, 1, 0}  \
}
 
#define O { \
    {0, 0, 0, 1, 1, 0, 0, 0}, \
    {0, 0, 1, 0, 0, 1, 0, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 1, 0, 0, 0, 0, 1, 0}, \
    {0, 0, 1, 0, 0, 1, 0, 0}, \
    {0, 0, 0, 1, 1, 0, 0, 0}  \
}
 
byte col = 0;
byte leds[8][8];

int pins[17]= {-1, 5, 4, 3, 2, 14, 15, 16, 17,13, 12, 11, 10, 9, 8, 7, 6, };
int rows[8] = {pins[16], pins[15], pins[11], pins[6], pins[10], pins[4], pins[3], pins[13]};
int cols[8] = {pins[9], pins[14], pins[8], pins[12], pins[1], pins[7], pins[2], pins[5]};
 
const int numPatterns = 6;
byte patterns[numPatterns][8][8] = {
  H,E,L,L,O,SPACE
};
 
int pattern = 0;
 
void setup() {
  
  for (int i = 1; i <= 16; i++) {
    pinMode(pins[i], OUTPUT);
  }
 
  
  for (int i = 1; i <= 8; i++) {
    digitalWrite(cols[i - 1], LOW);
  }
 
  for (int i = 1; i <= 8; i++) {
    digitalWrite(rows[i - 1], LOW);
  }
 
  clearLeds();
 
  
  FrequencyTimer2::disable();
  
  FrequencyTimer2::setPeriod(2000);

  FrequencyTimer2::setOnOverflow(display);
 
  setPattern(pattern);
}
 
void loop() {
    pattern = ++pattern % numPatterns;
    slidePattern(pattern, 60);
}
 
void clearLeds() {
 
  for (int i = 0; i < 8; i++) {
    for (int j = 0; j < 8; j++) {
      leds[i][j] = 0;
    }
  }
}
 
void setPattern(int pattern) {
  for (int i = 0; i < 8; i++) {
    for (int j = 0; j < 8; j++) {
      leds[i][j] = patterns[pattern][i][j];
    }
  }
}
 
void slidePattern(int pattern, int del) {
  for (int l = 0; l < 8; l++) {
    for (int i = 0; i < 7; i++) {
      for (int j = 0; j < 8; j++) {
        leds[j][i] = leds[j][i+1];
      }
    }
    for (int j = 0; j < 8; j++) {
      leds[j][7] = patterns[pattern][j][0 + l];
    }
    delay(del);
  }
}
 
// Interrupt routine
void display() {
  digitalWrite(cols[col], LOW); 
  col++;
  if (col == 8) {
    col = 0;
  }
  for (int row = 0; row < 8; row++) {
    if (leds[col][7 - row] == 1) {
      digitalWrite(rows[row], LOW);
    }
    else {
      digitalWrite(rows[row], HIGH);
    }
  }
  digitalWrite(cols[col], HIGH);
}

 原创！手都弄酸了😭