一、实验要求
1、R1和R2使用ppp链路直连,R2和R3把两条ppp链路捆绑为pppMP直连
2、按照图示配置IP地址
3、R2对R1的ppp进行单向chap验证
4、R2和R3的ppp进行双向chap验证
二、划分两个广播域
1、192.168.1.0/24
2、192.168.2.0/24
三、改名和接口配置IP
1.进入视图并改名为R1并配置接口IP
<Huawei>system-view # 进入[Huawei]视图
[Huawei]sysname R1 # 改名为R1
[R1]interface Serial 3/0/0 # 进入Serial 3/0/0接口
[R1-Serial3/0/0]ip address 192.168.1.1 24 # 配置Serial 3/0/0接口IP
[R1]display ip interface brief # 查看Serial 3/0/0接口IP是否配置成功
2. 进入Serial 3/0/0接口配置ppp
[R1]interface Serial 3/0/0 # 进入Serial 3/0/0接口
[R1-Serial3/0/0]ppp chap user wangdaye # 创建ppp用户名为wangdaye
[R1-Serial3/0/0]ppp chap password cipher wdy12345 #设置ppp用户wandaye的密码为wdy12345
3.进入视图并改名为R2并配置接口IP
<Huawei>system-view # 进入[Huawei]视图
[Huawei]sysname R2 # 改名为R2
[R2]interface Serial 3/0/0 # 进入Serial 3/0/0接口
[R2-Serial3/0/0]ip address 192.168.1.2 24 # 配置Serial 3/0/0接口IP
[R2]display ip interface brief # 查看Serial 3/0/0接口IP是否配置成功
4.配置R2
[R2]interface Mp-group 0/0/0 # 创建捆绑接口Mp-group0/0/0
[R2-Mp-group0/0/0]q
[R2]int Serial 4/0/0 # 进入Serial 4/0/0接口
[R2-Serial4/0/0]ppp mp Mp-group 0/0/0 # 将Serial 4/0/0接口加入捆绑接口Mp-group0/0/0
[R2-Serial4/0/0]
[R2-Serial4/0/0]quit # 退出接口
[R2]interface Mp-group 0/0/0 # 进入捆绑接口
[R2-Mp-group0/0/0]ip address 192.168.2.2 24 # 配置捆绑接口IP
[R2-Mp-group0/0/0]quit # 退出接口
[R2]
[R2]aaa # 进入aaa视图
[R2-aaa]local-user wangdaye password cipher wdy12345 #
Info: Add a new user.
[R2-aaa]local-user wangdaye service-type ppp
[R2-aaa]q
[R2]int Serial 3/0/0
[R2-Serial3/0/0]ppp authentication-mode chap #设置验证类型为chap
[R2-Serial3/0/0]quit
[R2]
[R2]aaa
[R2-aaa]local-user wangdaye password cipher wdy12345
[R2-aaa]local-user wangdaye service-type ppp
[R2-aaa]q
[R2]int Serial 3/0/1
[R2-Serial3/0/1]ppp authentication-mode chap # 设置接口报文的封装模式
[R2-Serial3/0/1]q
[R2]
[R2]int Serial 4/0/0
[R2-Serial4/0/0]ppp authentication-mode chap # 设置接口报文的封装模式
[R2-Serial4/0/0]q
[R2]
[R2]int Serial 3/0/1
[R2-Serial3/0/1]ppp chap user wangdaye
[R2-Serial3/0/1]ppp chap password cipher wdy12345
[R2-Serial3/0/1]q
5.配置R3
<R3>sys
[R3]
[R3]int Mp-group 0/0/0 # 创建捆绑接口Mp-group 0/0/0
[R3-Mp-group0/0/0]q
[R3]
[R3]int Serial 3/0/0
[R3-Serial3/0/0]ppp mp Mp-group 0/0/0 # 将Serial 3/0/0接口加进入捆绑接口Mp-group 0/0/0
[R3-Serial3/0/0]
[R3-Serial3/0/0]q
[R3]
[R3]int Serial 3/0/1
[R3-Serial3/0/1]ppp mp Mp-group 0/0/0 # 将Serial 3/0/1接口加进入捆绑接口Mp-group 0/0/0
[R3-Serial3/0/1]
[R3-Serial3/0/1]q
[R3]int Mp-group 0/0/0
[R3-Mp-group0/0/0]ip address 192.168.2.3 24 # 配置捆绑接口将Serial 3/0/0接口加进入捆绑接口Mp-group 0/0/0 IP地址
[R3-Mp-group0/0/0]q
[R3]display ip interface brief # 查看捆绑接口是否配置成功,双up则配置成功
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 2
The number of interface that is DOWN in Physical is 9
The number of interface that is UP in Protocol is 2
The number of interface that is DOWN in Protocol is 9
Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 unassigned down down
GigabitEthernet0/0/1 unassigned down down
GigabitEthernet0/0/2 unassigned down down
Mp-group0/0/0 192.168.2.3/24 up up
NULL0 unassigned up up(s)
Serial1/0/0 unassigned down down
Serial1/0/1 unassigned down down
Serial2/0/0 unassigned down down
Serial2/0/1 unassigned down down
Serial4/0/0 unassigned down down
Serial4/0/1 unassigned down down
[R3]
[R3]aaa # 进入aaa视图
[R3-aaa]local-user wangdaye password cipher wdy12345 #
Info: Add a new user.
[R3-aaa]local-user wangdaye service-type ppp
[R3-aaa]q
[R3]int Serial 3/0/0
[R3-Serial3/0/0]ppp authentication-mode chap #设置验证类型为chap
[R3-Serial3/0/0]quit
[R3]
[R3]aaa
[R3-aaa]local-user wangdaye password cipher wdy12345
[R3-aaa]local-user wangdaye service-type ppp
[R3-aaa]q
[R3]int Serial 3/0/1
[R3-Serial3/0/1]ppp authentication-mode chap # 设置接口报文的封装模式
[R3-Serial3/0/1]q
[R3]
[R3]int Serial 3/0/0
[R3-Serial3/0/0]ppp authentication-mode chap # 设置接口报文的封装模式
[R3-Serial3/0/0]q
[R3]
[R3]int Serial 3/0/1
[R3-Serial3/0/1]ppp chap user wangdaye
[R3-Serial3/0/1]ppp chap password cipher wdy12345
[R3-Serial3/0/1]q