AR1
<Huawei>
May 8 2024 16:33:08-08:00 Huawei %%01IFPDT/4/IF_STATE(l)[0]:Interface GigabitEt
hernet0/0/0 has turned into UP state.
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys
[Huawei]sysname
^
Error:Incomplete command found at '^' position.
[Huawei]sysname R1
[R1]
[R1]
[R1]in
[R1]info-center
[R1]interface g 0/0/0.1
[R1-GigabitEthernet0/0/0.1]ip ad
[R1-GigabitEthernet0/0/0.1]ip address 192.168.1.1 25
[R1-GigabitEthernet0/0/0.1]
[R1-GigabitEthernet0/0/0.1]do
[R1-GigabitEthernet0/0/0.1]dot1q te
[R1-GigabitEthernet0/0/0.1]dot1q termination vid 2
May 8 2024 16:35:34-08:00 R1 %%01IFNET/4/LINK_STATE(l)[1]:The line protocol IP
on the interface GigabitEthernet0/0/0.1 has entered the UP state.
[R1-GigabitEthernet0/0/0.1]
[R1-GigabitEthernet0/0/0.1]
[R1-GigabitEthernet0/0/0.1]arp b
[R1-GigabitEthernet0/0/0.1]arp broadcast e
[R1-GigabitEthernet0/0/0.1]arp broadcast enable
[R1-GigabitEthernet0/0/0.1]
[R1-GigabitEthernet0/0/0.1]dis
[R1-GigabitEthernet0/0/0.1]discard
[R1-GigabitEthernet0/0/0.1]display this
[R1-GigabitEthernet0/0/0.1]display this
[V200R003C00]
#
interface GigabitEthernet0/0/0.1
dot1q termination vid 2
ip address 192.168.1.1 255.255.255.128
arp broadcast enable
#
return
[R1-GigabitEthernet0/0/0.1]q
[R1]
[R1]
[R1]in
[R1]info-center
[R1]interface g 0/0/0.2
[R1-GigabitEthernet0/0/0.2]ip ad
[R1-GigabitEthernet0/0/0.2]ip address 192.168.1.129 25
[R1-GigabitEthernet0/0/0.2]
[R1-GigabitEthernet0/0/0.2]
[R1-GigabitEthernet0/0/0.2]do
[R1-GigabitEthernet0/0/0.2]dot1q te
[R1-GigabitEthernet0/0/0.2]dot1q termination e
[R1-GigabitEthernet0/0/0.2]dot1q termination e
^
Error: Unrecognized command found at '^' position.
[R1-GigabitEthernet0/0/0.2]do
[R1-GigabitEthernet0/0/0.2]dot1q te
[R1-GigabitEthernet0/0/0.2]dot1q termination vid 3
May 8 2024 16:37:18-08:00 R1 %%01IFNET/4/LINK_STATE(l)[2]:The line protocol IP
on the interface GigabitEthernet0/0/0.2 has entered the UP state.
[R1-GigabitEthernet0/0/0.2]
[R1-GigabitEthernet0/0/0.2]arp b
[R1-GigabitEthernet0/0/0.2]arp broadcast e
[R1-GigabitEthernet0/0/0.2]arp broadcast enable
[R1-GigabitEthernet0/0/0.2]
[R1-GigabitEthernet0/0/0.2]dis
[R1-GigabitEthernet0/0/0.2]discard
[R1-GigabitEthernet0/0/0.2]display this
[V200R003C00]
#
interface GigabitEthernet0/0/0.2
dot1q termination vid 3
ip address 192.168.1.129 255.255.255.128
arp broadcast enable
#
return
[R1-GigabitEthernet0/0/0.2]q
[R1]
[R1]
[R1]
[R1]
[R1]
[R1]dhcp e
[R1]dhcp enable
Info: The operation may take a few seconds. Please wait for a moment.done.
[R1]
[R1]
[R1]ip po
[R1]ip policy-based-route
[R1]ip pool vlan2
Info: It's successful to create an IP address pool.
[R1-ip-pool-vlan2]
[R1-ip-pool-vlan2]
[R1-ip-pool-vlan2]net`
[R1-ip-pool-vlan2]net
[R1-ip-pool-vlan2]netbios-type
[R1-ip-pool-vlan2]network 192.168.1.0 ma
[R1-ip-pool-vlan2]network 192.168.1.0 mask 25
[R1-ip-pool-vlan2]ga
[R1-ip-pool-vlan2]gateway-list 192.168.1.1
[R1-ip-pool-vlan2]dn
[R1-ip-pool-vlan2]dns-list 114.114.114.114 8.8.8.8
[R1-ip-pool-vlan2]
[R1-ip-pool-vlan2]
[R1-ip-pool-vlan2]q
[R1]
[R1]in
[R1]info-center
[R1]interface g 0/0/0.1
[R1-GigabitEthernet0/0/0.1]dh
[R1-GigabitEthernet0/0/0.1]dhcp se
[R1-GigabitEthernet0/0/0.1]dhcp select g
[R1-GigabitEthernet0/0/0.1]dhcp select global
[R1-GigabitEthernet0/0/0.1]dis
[R1-GigabitEthernet0/0/0.1]discard
[R1-GigabitEthernet0/0/0.1]display this
[R1-GigabitEthernet0/0/0.1]display this
[V200R003C00]
#
interface GigabitEthernet0/0/0.1
dot1q termination vid 2
ip address 192.168.1.1 255.255.255.128
arp broadcast enable
dhcp select global
#
return
[R1-GigabitEthernet0/0/0.1]
[R1-GigabitEthernet0/0/0.1]q
[R1]
[R1]
[R1]ip po
[R1]ip policy-based-route
[R1]ip pool vlan3
Info: It's successful to create an IP address pool.
[R1-ip-pool-vlan3]ne
[R1-ip-pool-vlan3]netbios-type
[R1-ip-pool-vlan3]network 192.168.1.128 mask25
^
Error:Too many parameters found at '^' position.
[R1-ip-pool-vlan3]network 192.168.1.128 mask 25
[R1-ip-pool-vlan3]ga
[R1-ip-pool-vlan3]gateway-list 192.168.1.129
[R1-ip-pool-vlan3]
[R1-ip-pool-vlan3]dn
[R1-ip-pool-vlan3]dns-list 114.114.114.114 8.8.8.8
[R1-ip-pool-vlan3]
[R1-ip-pool-vlan3]q
[R1]
[R1]
[R1]in
[R1]info-center
[R1]interface g 0/0/0.2
[R1-GigabitEthernet0/0/0.2]
[R1-GigabitEthernet0/0/0.2]
[R1-GigabitEthernet0/0/0.2]dh
[R1-GigabitEthernet0/0/0.2]dhcp s
[R1-GigabitEthernet0/0/0.2]dhcp select g
[R1-GigabitEthernet0/0/0.2]dhcp select global
[R1-GigabitEthernet0/0/0.2]
[R1-GigabitEthernet0/0/0.2]
[R1-GigabitEthernet0/0/0.2]q
[R1]
[R1]
[R1]q
<R1>save
The current configuration will be written to the device.
Are you sure to continue? (y/n)[n]:y
It will take several minutes to save configuration file, please wait.......
Configuration file had been saved successfully
Note: The configuration file will take effect after being activated
<R1>
LSW1
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys
[Huawei]sysname SW1
[SW1]
May 8 2024 16:05:11-08:00 SW1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 4, the c
hange loop count is 0, and the maximum number of records is 4095.
[SW1]
[SW1]
[SW1]
[SW1]v
[SW1]vlan2
^
Error: Unrecognized command found at '^' position.
[SW1]v
[SW1]vlan 2
[SW1-vlan2]q
[SW1]v
May 8 2024 16:06:11-08:00 SW1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 5, the c
hange loop count is 0, and the maximum number of records is 4095.
^
Error:Ambiguous command found at '^' position.
[SW1]v
[SW1]vlan 3
[SW1-vlan3]
[SW1-vlan3]
[SW1-vlan3]
May 8 2024 16:06:31-08:00 SW1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 6, the c
hange loop count is 0, and the maximum number of records is 4095.
[SW1-vlan3]q
[SW1]
[SW1]
[SW1]in
[SW1]info-center
[SW1]interface g 0/0/3
[SW1-GigabitEthernet0/0/3]
[SW1-GigabitEthernet0/0/3]p
[SW1-GigabitEthernet0/0/3]port l
[SW1-GigabitEthernet0/0/3]port link-
[SW1-GigabitEthernet0/0/3]port link-flap
[SW1-GigabitEthernet0/0/3]port link-type a
[SW1-GigabitEthernet0/0/3]port link-type access
[SW1-GigabitEthernet0/0/3]
[SW1-GigabitEthernet0/0/3]
May 8 2024 16:07:41-08:00 SW1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 7, the c
hange loop count is 0, and the maximum number of records is 4095.p
[SW1-GigabitEthernet0/0/3]port d
[SW1-GigabitEthernet0/0/3]port discard v
[SW1-GigabitEthernet0/0/3]port discard vlan 2
^
Error: Unrecognized command found at '^' position.
[SW1-GigabitEthernet0/0/3]port d
[SW1-GigabitEthernet0/0/3]port discard
[SW1-GigabitEthernet0/0/3]port default vlan 2
[SW1-GigabitEthernet0/0/3]
May 8 2024 16:09:11-08:00 SW1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 8, the c
hange loop count is 0, and the maximum number of records is 4095.
[SW1-GigabitEthernet0/0/3]
[SW1-GigabitEthernet0/0/3]
[SW1-GigabitEthernet0/0/3]
[SW1-GigabitEthernet0/0/3]q
[SW1]
[SW1]in
[SW1]info-center
[SW1]interface g 0/0/4
[SW1-GigabitEthernet0/0/4]po
[SW1-GigabitEthernet0/0/4]port l
[SW1-GigabitEthernet0/0/4]port link-
[SW1-GigabitEthernet0/0/4]port link-flap
[SW1-GigabitEthernet0/0/4]port link-type a
[SW1-GigabitEthernet0/0/4]port link-type access
[SW1-GigabitEthernet0/0/4]
[SW1-GigabitEthernet0/0/4]
May 8 2024 16:09:51-08:00 SW1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 9, the c
hange loop count is 0, and the maximum number of records is 4095.po
[SW1-GigabitEthernet0/0/4]port d
[SW1-GigabitEthernet0/0/4]port discard
[SW1-GigabitEthernet0/0/4]port default vlan 3
[SW1-GigabitEthernet0/0/4]
[SW1-GigabitEthernet0/0/4]
[SW1-GigabitEthernet0/0/4]
May 8 2024 16:10:31-08:00 SW1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 10, the
change loop count is 0, and the maximum number of records is 4095.
[SW1-GigabitEthernet0/0/4]
[SW1-GigabitEthernet0/0/4]
[SW1-GigabitEthernet0/0/4]q
[SW1]
[SW1]
[SW1]
[SW1]in
[SW1]info-center
[SW1]interface g 0/0/2
[SW1-GigabitEthernet0/0/2]p
[SW1-GigabitEthernet0/0/2]port l
[SW1-GigabitEthernet0/0/2]port link-
[SW1-GigabitEthernet0/0/2]port link-flap
[SW1-GigabitEthernet0/0/2]port link-type t
[SW1-GigabitEthernet0/0/2]port link-type trunk
[SW1-GigabitEthernet0/0/2]
May 8 2024 16:11:21-08:00 SW1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 11, the
change loop count is 0, and the maximum number of records is 4095.po
[SW1-GigabitEthernet0/0/2]
[SW1-GigabitEthernet0/0/2]po
[SW1-GigabitEthernet0/0/2]port t
[SW1-GigabitEthernet0/0/2]port trunk a
[SW1-GigabitEthernet0/0/2]port trunk allow-pass vlan all
[SW1-GigabitEthernet0/0/2]
May 8 2024 16:12:11-08:00 SW1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 12, the
change loop count is 0, and the maximum number of records is 4095.
[SW1-GigabitEthernet0/0/2]in
[SW1-GigabitEthernet0/0/2]in
[SW1-GigabitEthernet0/0/2]in
[SW1-GigabitEthernet0/0/2]in
[SW1-GigabitEthernet0/0/2]in
[SW1-GigabitEthernet0/0/2]q
[SW1]in
[SW1]info-center
[SW1]interface
[SW1]info-center
[SW1]interface g 0/0/1
[SW1-GigabitEthernet0/0/1]
[SW1-GigabitEthernet0/0/1]
[SW1-GigabitEthernet0/0/1]po
[SW1-GigabitEthernet0/0/1]port l
[SW1-GigabitEthernet0/0/1]port link-
[SW1-GigabitEthernet0/0/1]port link-flap
[SW1-GigabitEthernet0/0/1]port link-type t
[SW1-GigabitEthernet0/0/1]port link-type trunk
[SW1-GigabitEthernet0/0/1]
May 8 2024 16:13:01-08:00 SW1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 13, the
change loop count is 0, and the maximum number of records is 4095.
[SW1-GigabitEthernet0/0/1]
[SW1-GigabitEthernet0/0/1]po
[SW1-GigabitEthernet0/0/1]port t
[SW1-GigabitEthernet0/0/1]port trunk a
[SW1-GigabitEthernet0/0/1]port trunk allow-pass vlan all
[SW1-GigabitEthernet0/0/1]
[SW1-GigabitEthernet0/0/1]
May 8 2024 16:13:21-08:00 SW1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 14, the
change loop count is 0, and the maximum number of records is 4095.
May 8 2024 16:18:15-08:00 SW1 %%01PHY/1/PHY(l)[0]: GigabitEthernet0/0/2: cha
nge status to down
May 8 2024 16:18:16-08:00 SW1 %%01PHY/1/PHY(l)[1]: GigabitEthernet0/0/2: cha
nge status to up User interface con0 is available
Please Press ENTER.
<SW1>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
Info: Please input the file name ( *.cfg, *.zip ) [vrpcfg.zip]:
May 8 2024 16:49:59-08:00 SW1 %%01CFM/4/SAVE(l)[0]:The user chose Y when decidi
ng whether to save the configuration to the device.
Now saving the current configuration to the slot 0.
Save the configuration successfully.
<SW1>
LSW2
<Huawei>sys
<Huawei>system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sy
[Huawei]sysname SW2
[SW2]
May 8 2024 16:13:44-08:00 SW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 4, the c
hange loop count is 0, and the maximum number of records is 4095.
[SW2]
[SW2]ion
[SW2]in
[SW2]info-center
[SW2]vlan 2
[SW2-vlan2]
[SW2-vlan2]q
[SW2]vlan
May 8 2024 16:14:14-08:00 SW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 5, the c
hange loop count is 0, and the maximum number of records is 4095.
^
Error:Incomplete command found at '^' position.
[SW2]vlan3
^
Error: Unrecognized command found at '^' position.
[SW2]vlan 3
[SW2-vlan3]q
[SW2]
[SW2]
[SW2]
May 8 2024 16:14:34-08:00 SW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 6, the c
hange loop count is 0, and the maximum number of records is 4095.
[SW2]in
[SW2]info-center
[SW2]interface g 0/0/2
[SW2-GigabitEthernet0/0/2]po
[SW2-GigabitEthernet0/0/2]port l
[SW2-GigabitEthernet0/0/2]port link-
[SW2-GigabitEthernet0/0/2]port link-flap
[SW2-GigabitEthernet0/0/2]port link-type a
[SW2-GigabitEthernet0/0/2]port link-type access
[SW2-GigabitEthernet0/0/2]po
[SW2-GigabitEthernet0/0/2]port
May 8 2024 16:15:14-08:00 SW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 7, the c
hange loop count is 0, and the maximum number of records is 4095.
^
Error:Incomplete command found at '^' position.
[SW2-GigabitEthernet0/0/2]po
[SW2-GigabitEthernet0/0/2]port d
[SW2-GigabitEthernet0/0/2]port discard
[SW2-GigabitEthernet0/0/2]port default vlan 2
[SW2-GigabitEthernet0/0/2]
May 8 2024 16:15:34-08:00 SW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 8, the c
hange loop count is 0, and the maximum number of records is 4095.q
[SW2]
[SW2]
[SW2]in
[SW2]info-center
[SW2]interface g 0/0/3
[SW2-GigabitEthernet0/0/3]po
[SW2-GigabitEthernet0/0/3]port l
[SW2-GigabitEthernet0/0/3]port link-
[SW2-GigabitEthernet0/0/3]port link-flap
[SW2-GigabitEthernet0/0/3]port link-type a
[SW2-GigabitEthernet0/0/3]port link-type access
[SW2-GigabitEthernet0/0/3]po
[SW2-GigabitEthernet0/0/3]port
May 8 2024 16:16:04-08:00 SW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 9, the c
hange loop count is 0, and the maximum number of records is 4095.
^
Error:Incomplete command found at '^' position.
[SW2-GigabitEthernet0/0/3]po
[SW2-GigabitEthernet0/0/3]port d
[SW2-GigabitEthernet0/0/3]port discard
[SW2-GigabitEthernet0/0/3]port default vlan 3
[SW2-GigabitEthernet0/0/3]
May 8 2024 16:16:24-08:00 SW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 10, the
change loop count is 0, and the maximum number of records is 4095.
[SW2-GigabitEthernet0/0/3]
[SW2-GigabitEthernet0/0/3]q
[SW2]
[SW2]in
[SW2]info-center
[SW2]info-center
[SW2]info-center
[SW2]in
[SW2]info-center
[SW2]interface g 0/0/1
[SW2-GigabitEthernet0/0/1]po
[SW2-GigabitEthernet0/0/1]port l
[SW2-GigabitEthernet0/0/1]port link-
[SW2-GigabitEthernet0/0/1]port link-flap
[SW2-GigabitEthernet0/0/1]port link-type t
[SW2-GigabitEthernet0/0/1]port link-type trunk
[SW2-GigabitEthernet0/0/1]
May 8 2024 16:16:54-08:00 SW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 11, the
change loop count is 0, and the maximum number of records is 4095.po
[SW2-GigabitEthernet0/0/1]port t
[SW2-GigabitEthernet0/0/1]port trunk a
[SW2-GigabitEthernet0/0/1]port trunk allow-pass v
[SW2-GigabitEthernet0/0/1]port trunk allow-pass vlan all
[SW2-GigabitEthernet0/0/1]port trunk allow-pass vlan all
[SW2-GigabitEthernet0/0/1]
May 8 2024 16:17:14-08:00 SW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 12, the
change loop count is 0, and the maximum number of records is 4095.
[SW2-GigabitEthernet0/0/1] User interface con0 is available
Please Press ENTER.
<SW2>sa
<SW2>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]Y
Info: Please input the file name ( *.cfg, *.zip ) [vrpcfg.zip]:
May 8 2024 16:50:42-08:00 SW2 %%01CFM/4/SAVE(l)[0]:The user chose Y when decidi
ng whether to save the configuration to the device.
Now saving the current configuration to the slot 0.
Save the configuration successfully.
<SW2>