HCIP MGRE实验

 

要求如图，其中第五条应该为r1 r3 r4

首先配置ISP上的认证和ip：

[isp]int s3/0/0
[isp-Serial3/0/0]link-protocol hdlc 

[r2-Serial3/0/0]int s3/0/1 
[r2-Serial3/0/1]ppp authentication-mode pap 
[r2-Serial3/0/1]ip add 32.1.1.2 24
[r2-Serial3/0/1]int s3/0/0
[r2-Serial3/0/0]ip add 12.1.1.2 24
[r2-Serial3/0/0]q
[r2]aaa   
[r2-aaa]local-user aaa privilege level 15 password cipher 123456
Info: Add a new user. 
[r2-aaa]local-user aaa service-type ppp 
[r2-aaa]local-user bbb privilege level 15 password cipher 654321
Info: Add a new user. 
[r2-aaa]local-user bbb service-type ppp
[r2-aaa]int s4/0/0 
[r2-Serial4/0/0]ppp authentication-mode chap 
[r2-Serial4/0/0]ip add 42.1.1.2 24
 

接着在各路由器上配置认证和ip：

[r1]int s4/0/0 
[r1-Serial4/0/0]link-protocol hdlc 
[r1-Serial4/0/0]ip add 12.1.1.1 24
[r1-Serial4/0/0]int g0/0/0
[r1-GigabitEthernet0/0/0]ip add 192.168.1.254 24
[r1]ip route-static 0.0.0.0 0 12.1.1.2

[r3]int g0/0/0
[r3-GigabitEthernet0/0/0]ip add 192.168.2.254 24
[r3-GigabitEthernet0/0/0]int s4/0/0
[r3-Serial4/0/0]ip add 32.1.1.1 24
[r3-Serial4/0/0]ppp pap local-user aaa password cipher 123456
[r3]ip route-static 0.0.0.0 0 32.1.1.2
 

[r4]int g0/0/0
[r4-GigabitEthernet0/0/0]ip add 192.168.3.254 24
[r4-GigabitEthernet0/0/0]int s4/0/0
[r4-Serial4/0/0]ip add 42.1.1.1 24
[r4-Serial4/0/0]ppp chap user bbb 
[r4-Serial4/0/0]ppp chap password cipher 654321
[r4]ip route-static 0.0.0.0 0 42.1.1.2

初步测试一下内网联通性：

 接下来配置MGRE:

  
[r1]interface Tunnel 0/0/0
[r1-Tunnel0/0/0]ip add 10.1.1.1 24 
[r1-Tunnel0/0/0]tunnel-protocol gre p2mp 
[r1-Tunnel0/0/0]source 12.1.1.1
[r1-Tunnel0/0/0]nhrp entry multicast dynamic 
[r1-Tunnel0/0/0]nhrp network-id 100

   
[r3]interface Tunnel 0/0/0
[r3-Tunnel0/0/0]ip add 10.1.1.2 24 
[r3-Tunnel0/0/0]tunnel-protocol gre p2mp  
[r3-Tunnel0/0/0]source s4/0/0
[r3-Tunnel0/0/0]nhrp entry 10.1.1.1 12.1.1.1 register 
[r3-Tunnel0/0/0]nhrp network-id 100

[r4]int t0/0/0
[r4-Tunnel0/0/0]ip add 10.1.1.3 24 
[r4-Tunnel0/0/0]tunnel-protocol gre p2mp  
[r4-Tunnel0/0/0]source s4/0/0
[r4-Tunnel0/0/0]nhrp entry 10.1.1.1 12.1.1.1 register
[r4-Tunnel0/0/0]nhrp network-id 100 

配置RIP：

r1]rip 1
[r1-rip-1]version 2
[r1-rip-1]network 192.168.1.0 
[r1-rip-1]network 10.0.0.0
[r1-Tunnel0/0/0]undo rip split-horizon 

[r3]rip 1
[r3-rip-1]version 2
[r3-rip-1]network 192.168.2.0
[r3-rip-1]network 10.0.0.0

[r4]rip 1
[r4-rip-1]ver 2 
[r4-rip-1]network 192.168.3.0
[r4-rip-1]network 10.0.0.0

 [r1]acl 2000
[r1-acl-basic-2000]rule permit source 192.168.1.0 0.0.0.255
[r1-acl-basic-2000]int 4
[r1-Serial4/0/0]nat outbound 2000

[r3]acl 2000
[r3-acl-basic-2000]rule permit source 192.168.2.0 0.0.0.255
[r3]int s4/0/0
[r3-Serial4/0/0]nat outbound 2000

[r4]acl 2000 
[r4-acl-basic-2000]rule permit source 192.168.3.0 0.0.0.255
[r4-Serial4/0/0]nat outbound 2000