OSPF网络连接

拓扑结构：

实验要求： 

1.R6为ISP只能配置IP地址，R1-R5的环回为私有网段

2.R1/R4/R5为全连的MGRE结构，R1/R2/R3为星型的拓扑结构，R1为中心站点

3.所有的私有网段可以相互通讯，私有网段使用OSPF完成

实验配置：

接口配置：

R1：

[r1]interface GigabitEthernet 0/0/0

[r1-GigabitEthernet0/0/0]ip address 15.0.0.1 8

[r1]interface GigabitEthernet 0/0/1

[r1-GigabitEthernet0/0/1]ip address 65.0.0.1 8

[r1]interface LoopBack 0

[r1-LoopBack0]ip address 192.168.1.1 24

[r1]ip route-static 0.0.0.0 0 15.0.0.2

[r1]ip route-static 0.0.0.0 0 65.0.0.2

R2：

[r2]interface GigabitEthernet 0/0/0

[r2-GigabitEthernet0/0/0]ip address 25.0.0.1 8

[r2]interface LoopBack 0

[r2-LoopBack0]ip address 192.168.2.1 24

[r2]ip route-static 0.0.0.0 0 25.0.0.2

R3：

[r3]interface GigabitEthernet 0/0/0

[r3-GigabitEthernet0/0/0]ip address 35.0.0.1 8

[r3]interface LoopBack 0

[r3-LoopBack0]ip address 192.168.3.1 24

[r3]ip route-static 0.0.0.0 0 35.0.0.2

 R4：

[r4]interface GigabitEthernet 0/0/0

[r4-GigabitEthernet0/0/0]ip address 45.0.0.1 8

[r4]interface LoopBack 0

[r4-LoopBack0]ip address 192.168.4.1 24

[r4]ip route-static 0.0.0.0 0 45.0.0.2

R5：

[r5]interface GigabitEthernet 0/0/0

[r5-GigabitEthernet0/0/0]ip address 55.0.0.1 8

[r5]interface LoopBack 0

[r5-LoopBack0]ip address 192.168.5.1 24

[r5]ip route-static 0.0.0.0 0 55.0.0.2

R6：

[ISP]interface GigabitEthernet 0/0/0

[ISP-GigabitEthernet0/0/0]ip address 15.0.0.2 8

[ISP]interface GigabitEthernet 0/0/1

[ISP-GigabitEthernet0/0/1]ip address 65.0.0.2 8

[ISP]interface GigabitEthernet 2/0/0

[ISP-GigabitEthernet2/0/0]ip address 25.0.0.2 8

[ISP]interface GigabitEthernet 3/0/0

[ISP-GigabitEthernet3/0/0]ip address 35.0.0.2 8

[ISP]interface GigabitEthernet 4/0/0

[ISP-GigabitEthernet4/0/0]ip address 45.0.0.2 8

[ISP]interface GigabitEthernet 0/0/2

[ISP-GigabitEthernet0/0/2]ip address 55.0.0.2 8

配置完成后，公网之间已经连通 

MGRE配置：

R1：

[r1]interface Tunnel 0/0/0

[r1-Tunnel0/0/0]ip address 192.168.6.1 24

[r1-Tunnel0/0/0]tunnel-protocol gre p2mp

[r1-Tunnel0/0/0]source 15.0.0.1 

[r1-Tunnel0/0/0]nhrp network-id 100

[r1-Tunnel0/0/0]nhrp entry 192.168.6.2 45.0.0.1 register 

[r1-Tunnel0/0/0]nhrp entry 192.168.6.3 55.0.0.1 register 

[r1]interface Tunnel 0/0/1

[r1-Tunnel0/0/1]ip address 192.168.7.1 24

[r1-Tunnel0/0/1]tunnel-protocol gre p2mp    

[r1-Tunnel0/0/1]source 65.0.0.1

[r1-Tunnel0/0/1]nhrp network-id 200

R2：

[r2]interface Tunnel 0/0/0

[r2-Tunnel0/0/0]ip address 192.168.7.2 24

[r2-Tunnel0/0/0]tunnel-protocol gre p2mp

[r2-Tunnel0/0/0]source 25.0.0.1

[r2-Tunnel0/0/0]nhrp network-id 200

[r2-Tunnel0/0/0]nhrp entry 192.168.7.1 65.0.0.1 register 

R3：

 [r3]interface Tunnel 0/0/0

[r3-Tunnel0/0/0]ip address 192.168.7.3 24

[r3-Tunnel0/0/0]tunnel-protocol gre p2mp

[r3-Tunnel0/0/0]source 35.0.0.1

[r3-Tunnel0/0/0]nhrp network-id 200

[r3-Tunnel0/0/0]nhrp entry 192.168.7.1 65.0.0.1 register 

 R4：

[r4]interface Tunnel 0/0/0

[r4-Tunnel0/0/0]ip address 192.168.6.2 24

[r4-Tunnel0/0/0]tunnel-protocol gre p2mp

[r4-Tunnel0/0/0]source 45.0.0.1

[r4-Tunnel0/0/0]nhrp network-id 100

[r4-Tunnel0/0/0]nhrp entry 192.168.6.1 15.0.0.1 register 

[r4-Tunnel0/0/0]nhrp entry 192.168.6.3 55.0.0.1  register 

R5：

[r5]interface Tunnel 0/0/0

[r5-Tunnel0/0/0]ip address 192.168.6.3 24

[r5-Tunnel0/0/0]tunnel-protocol gre p2mp

[r5-Tunnel0/0/0]source 55.0.0.1

[r5-Tunnel0/0/0]nhrp network-id 100

[r5-Tunnel0/0/0]nhrp entry 192.168.6.1 15.0.0.1 register 

[r5-Tunnel0/0/0]nhrp entry 192.168.6.2 45.0.0.1 register 

完成配置后，建立好了NHRP表

OSPF配置：

R1：

[r1]ospf router-id 1.1.1.1

[r1-ospf-1]area 0

[r1-ospf-1-area-0.0.0.0]network 192.168.6.0 0.0.0.255

[r1-ospf-1-area-0.0.0.0]network 192.168.1.0 0.0.0.255

[r1-Tunnel0/0/0]nhrp entry multicast dynamic 

[r1-Tunnel0/0/0]ospf network-type broadcast 

[r1-Tunnel0/0/1]nhrp entry multicast dynamic 

[r1-Tunnel0/0/1]ospf network-type  broadcast

R2；

[r2]ospf 1 router-id 2.2.2.2

[r2-ospf-1]area 0

[r2-ospf-1-area-0.0.0.0]network 192.168.2.0 0.0.0.255

[r2-ospf-1-area-0.0.0.0]network 192.168.7.0 0.0.0.255

[r2-Tunnel0/0/0]ospf network-type broadcast 

R3：

[r3]ospf 1 router-id 3.3.3.3

[r3-ospf-1]area 0

[r3-ospf-1-area-0.0.0.0]network 192.168.3.0 0.0.0.255

[r3-ospf-1-area-0.0.0.0]network 192.168.7.0 0.0.0.255

[r3-Tunnel0/0/0]ospf network-type broadcast 

R4：

[r4]ospf router-id 4.4.4.4

[r4-ospf-1]area 0

[r4-ospf-1-area-0.0.0.0]network 192.168.6.0 0.0.0.255

[r4-ospf-1-area-0.0.0.0]network 192.168.4.0 0.0.0.255

[r4-Tunnel0/0/0]ospf network-type broadcast 

R5：

[r5]ospf router-id 5.5.5.5

[r5-ospf-1]area 0

[r5-ospf-1-area-0.0.0.0]network 192.168.6.0 0.0.0.255

[r5-ospf-1-area-0.0.0.0]network 192.168.5.0 0.0.0.255

[r5-Tunnel0/0/0]ospf network-type broadcast

 完成配置后，查看OSPF表

 实验结果：

网络连通