本文仅作为个人学习所用
项目二-按键控制LED灯操作步骤
在工程文件中新建Hardware文件夹用于存放封装的函数
LED.c文件中存放LED状态的函数
#include "stm32f10x.h" // Device header
void LED_Init(void)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA,ENABLE);
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1 | GPIO_Pin_2;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA,&GPIO_InitStructure);
GPIO_SetBits(GPIOA,GPIO_Pin_1 | GPIO_Pin_2); //A1、A2引脚默认输出高电平,LED默认状态为熄灭
}
void LED1_ON(void)
{
GPIO_ResetBits(GPIOA,GPIO_Pin_1); //A1输出低电平,LED亮
}
void LED1_OFF(void)
{
GPIO_SetBits(GPIOA,GPIO_Pin_1); //A2输出高电平,LED灭
}
void LED1_Turn(void)
{
if (GPIO_ReadOutputDataBit(GPIOA,GPIO_Pin_1) == 0)
{
GPIO_SetBits(GPIOA,GPIO_Pin_1);
}
else
{
GPIO_ResetBits(GPIOA,GPIO_Pin_1);
}
}
void LED2_ON(void)
{
GPIO_ResetBits(GPIOA,GPIO_Pin_2); //A1输出低电平,LED亮
}
void LED2_OFF(void)
{
GPIO_SetBits(GPIOA,GPIO_Pin_2); //A2输出高电平,LED灭
}
void LED2_Turn(void)
{
if (GPIO_ReadOutputDataBit(GPIOA,GPIO_Pin_2) == 0)
{
GPIO_SetBits(GPIOA,GPIO_Pin_2);
}
else
{
GPIO_ResetBits(GPIOA,GPIO_Pin_2);
}
}
其中LED_ON/OFF为开启关闭LED灯状态,LED_Turn为反转GPIO口实现LED亮灭的函数
LED.h文件内容
#ifndef __LED_H
#define __LED_H
void LED_Init(void);
void LED1_Turn(void);
void LED2_Turn(void);
#endif
用Key.c文件存放按键控制的函数
#include "stm32f10x.h" // Device header
#include "Delay.h"
void Key_Init(void)
{
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB,ENABLE);
GPIO_InitTypeDef GPIO_InitStructure;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1 | GPIO_Pin_11;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOB,&GPIO_InitStructure);
}
uint8_t Key_GetNum(void)
{
uint8_t KeyNum = 0;
if (GPIO_ReadInputDataBit(GPIOB,GPIO_Pin_1) == 0)
{
Delay_ms(20);
while (GPIO_ReadInputDataBit(GPIOB,GPIO_Pin_1) == 0);
Delay_ms(20);
KeyNum = 1;
}
if (GPIO_ReadInputDataBit(GPIOB,GPIO_Pin_11) == 0)
{
Delay_ms(20);
while (GPIO_ReadInputDataBit(GPIOB,GPIO_Pin_11) == 0);
Delay_ms(20);
KeyNum = 2;
}
return KeyNum;
}
Key.h文件
#ifndef __KEY_H
#define __KEY_H
void Key_Init(void);
uint8_t Key_GetNum(void);
#endif
main.c文件
#include "stm32f10x.h" // Device header
#include "Delay.h"
#include "LED.h"
#include "Key.h"
uint8_t KeyNum;
int main(void)
{
LED_Init();
Key_Init();
while(1)
{
KeyNum = Key_GetNum();
if (KeyNum == 1)
{
LED1_Turn();
}
if (KeyNum == 2)
{
LED2_Turn();
}
}
}