【无标题】11

1.拓扑图

 

2.要求

1.R6为ISP只能配置IP地址，R1-R5的环回为私有网段

2.R1/4/5为全连的MGRE结构，R1/2/3为星型的拓扑结构，

3.R1为中心站点所有私有网段可以互相通讯，私有网段使用oSPF完成。

3.命令

R1

配置接口ip

[R1-GigabitEthernet0/0/0]ip ad 1.1.1.1 24

[R1-GigabitEthernet0/0/1]ip ad 1.2.2.1 24

[R1]interface  LoopBack 0

[R1-LoopBack0]ip ad 192.168.1.1 24

配置缺省路由

[R1]ip route-static 0.0.0.0 0 1.1.1.2

[R1]ip route-static 0.0.0.0 0 1.2.2.2

配置中心站点

[R1]interface Tunnel 0/0/0

[R1-Tunnel0/0/0]ip address 192.168.7.1 24

[R1-Tunnel0/0/0]tunnel-protocol gre p2mp

[R1-Tunnel0/0/0]source 1.1.1.1 24

[R1-Tunnel0/0/0]nhrp network-id 10

[R1-Tunnel0/0/0]ospf network-type p2mp

[R1-Tunnel0/0/0]nhrp entry multicast dynamic

[R1]ospf 1 router-id 1.1.1.1

[R1-ospf-1]area 0

[R1-ospf-1-area-0.0.0.0]network 192.168.1.1 0.0.0.0

[R1-ospf-1-area-0.0.0.0]network 192.168.7.1 0.0.0.0

[R1]interface Tunnel 0/0/1

[R1-Tunnel0/0/1]ip address 192.168.8.1 24

[R1-Tunnel0/0/1]tunnel-protocol gre p2mp

[R1-Tunnel0/0/1]source 1.2.2.1

[R1-Tunnel0/0/1]nhrp network-id 11

[R1-Tunnel0/0/1]nhrp entry multicast dynamic

[R1-Tunnel0/0/1]nhrp entry 192.168.8.2 4.4.4.1 register

[R1-Tunnel0/0/1]nhrp entry 192.168.8.3 5.5.5.1 register

[R1-Tunnel0/0/1]ospf network-type p2mp

[R1-ospf-1-area-0.0.0.0]network 192.168.8.1 0.0.0.0

R2

配置接口ip

[r2-GigabitEthernet0/0/0]ip ad 2.2.2.1 24

[r2-LoopBack0]ip ad 192.168.2.1 24

配置缺省

[r2]ip route-static 0.0.0.0 0 2.2.2.2

配置分支

[r2]interface Tunnel 0/0/0

[r2-Tunnel0/0/0]ip ad 192.168.7.2 24

[r2-Tunnel0/0/0]tunnel-protocol gre p2mp

[r2-Tunnel0/0/0]nhrp network-id 10

[r2-Tunnel0/0/0]nhrp entry 192.168.7.2 1.1.1.1 register

[r2-Tunnel0/0/0]ospf network-type p2mp

[r2]ospf 1 router-id 2.2.2.2

[r2-ospf-1]area 0

[r2-ospf-1-area-0.0.0.0]network 192.168.7.2 0.0.0.0

[r2-ospf-1-area-0.0.0.0]network 192.168.2.1 0.0.0.0

R3

配置接口IP

[r3-GigabitEthernet0/0/0]ip ad 3.3.3.1 24

[r3-LoopBack0]ip ad 192.168.3.1 24

配置缺省

[r3]ip route-static 0.0.0.0 0 3.3.3.2

配置分支

[r3]interface Tunnel 0/0/0

[r3-Tunnel0/0/0]ip ad 192.168.7.3 24

[r3-Tunnel0/0/0]tunnel-protocol gre p2mp

[r3-Tunnel0/0/0]source GigabitEthernet 0/0/0

[r3-Tunnel0/0/0]nhrp network-id 10

[r3-Tunnel0/0/0]nhrp entry 192.168.7.1 1.1.1.1 register 

[r3-Tunnel0/0/0]ospf network-type p2mp

[r3]ospf 1 router-id 3.3.3.3

[r3-ospf-1]area 0

[r3-ospf-1-area-0.0.0.0]network 192.168.3.1 0.0.0.0

[r3-ospf-1-area-0.0.0.0]network 192.168.7.3 0.0.0.0

R4

配置接口IP

[r4-GigabitEthernet0/0/0]ip ad 4.4.4.1 24

[r4-LoopBack0]ip ad 192.168.4.1 24

配置缺

[r4]ip route-static 0.0.0.0 0 4.4.4.2

配中心

[r4]int Tunnel 0/0/0

[r4-Tunnel0/0/0]ip ad 192.168.8.2 24

[r4-Tunnel0/0/0]tunnel-protocol gre p2mp

[r4-Tunnel0/0/0]nhrp network-id 11

[r4-Tunnel0/0/0]source 4.4.4.1

[r4-Tunnel0/0/0]nhrp entry multicast dynamic

[r4-Tunnel0/0/0]nhrp entry 192.168.8.3 5.5.5.1 register

 [r4-Tunnel0/0/0]nhrp entry 192.168.8.1 1.2.2.1 register

[r4-Tunnel0/0/0]ospf network-type p2mp

[r4]ospf 1 router-id  4.4.4.1

[r4-ospf-1]area 0

[r4-ospf-1-area-0.0.0.0]network 192.168.8.2 0.0.0.0

[r4-ospf-1-area-0.0.0.0]network 192.168.4.1 0.0.0.0

R5

配置接口ip

[r5-GigabitEthernet0/0/0]ip ad 5.5.5.1 24

[r5-LoopBack0]ip ad 192.168.5.1 24

配置缺省

[r5]ip route-static 0.0.0.0 0 5.5.5.2

配中心

[r5]interface Tunnel 0/0/0

[r5-Tunnel0/0/0]ip address 192.168.8.3 24

[r5-Tunnel0/0/0]tunnel-protocol gre p2mp

[r5-Tunnel0/0/0]source 5.5.5.1

[r5-Tunnel0/0/0]nhrp network-id 11

[r5-Tunnel0/0/0]nhrp entry multicast dynamic

[r5-Tunnel0/0/0]nhrp entry 192.168.8.2 4.4.4.1 register

[r5-Tunnel0/0/0]nhrp  entry 192.168.8.1 1.2.2.1 register

[r5-Tunnel0/0/0]ospf network-type p2mp

[r5]ospf 1 router-id 5.5.5.1

[r5-ospf-1]area 0

[r5-ospf-1-area-0.0.0.0]network 192.168.8.3 0.0.0.0

[r5-ospf-1-area-0.0.0.0]network 192.168.5.1 0.0.0.0

R6

接口配置

[r6-GigabitEthernet0/0/0]ip ad 1.1.1.2 24

[r6-GigabitEthernet0/0/1]ip ad 1.2.2.2 24

[r6-GigabitEthernet0/0/2]ip ad 2.2.2.2 24

[r6-GigabitEthernet4/0/0]ip ad 3.3.3.2 24

[r6-GigabitEthernet4/0/1]ip address 4.4.4.2 24

[r6-GigabitEthernet4/0/2]ip ad 5.5.5.2 24

[r6-LoopBack0]ip ad 192.168.6.1 24

4.测试

使用R2 ping通各个环回