数字温度计，RTC与I2C、OLED的联合使用
（一）RTC实现日历输出
（1）Cube工程创建;
RCC设置：
RTC设置
RTC具体时间设置：设置为当天，便于时间查找
串口设置：
时钟设置：
代码设置：
主函数前：
//添加头文件#include "stdio.h"
int fputc(int ch,FILE *f){
uint8_t temp[1]={ch};
HAL_UART_Transmit(&huart1,temp,1,2);
return ch;
}
main函数内：定义结构体
RTC_DateTypeDef GetData; //获取日期结构体
RTC_TimeTypeDef GetTime; //获取时间结构体
while内：
/* Get the RTC current Time */
HAL_RTC_GetTime(&hrtc, &GetTime, RTC_FORMAT_BIN);
/* Get the RTC current Date */
HAL_RTC_GetDate(&hrtc, &GetData, RTC_FORMAT_BIN);
/* Display date Format : yy/mm/dd */
printf("%02d/%02d/%02d\r\n",2000 + GetData.Year, GetData.Month, GetData.Date);
/* Display time Format : hh:mm:ss */
printf("%02d:%02d:%02d\r\n",GetTime.Hours, GetTime.Minutes, GetTime.Seconds);
printf("\r\n");
HAL_Delay(1000);
检查是否打开printf串口输出：
烧录结果：
（二）数字温度计
本部分为I2C、OLED、RTC结合即可
鉴于OLED部分之前只做了SPI的标准库实现，这里给出HAL库实现
选择SPI2，选择SPI2后PB13、PB15分别为SPI2_SCK、SPI2_MOSI，
并另外选择三个引脚，为了方便与标准库进行对比，引脚分别命名，如下
此处给出OLED的HAL库代码
oled.h:
#ifndef __OLED_H
#define __OLED_H
#include "stm32f1xx_hal.h"
//--------------OLED参数定义---------------------
#define PAGE_SIZE 8
#define XLevelL 0x00
#define XLevelH 0x10
#define YLevel 0xB0
#define Brightness 0xFF
#define WIDTH 128
#define HEIGHT 64
//-------------写命令和数据定义-------------------
#define OLED_CMD 0 //写命令
#define OLED_DATA 1 //写数据
//-----------------OLED端口定义----------------
/*
#define OLED_CS GPIO_PIN_11 //片选信号 PB11
#define OLED_DC GPIO_PIN_10 //数据/命令控制信号 PB10
#define OLED_RST GPIO_PIN_12 //复位信号 PB12
*/
// 设置（定义）RES、DC、CS 所使用的引脚
// RES
#define OLED_RST_GPIO_Port GPIOB
#define OLED_RST_Pin GPIO_PIN_12
// DC
#define OLED_DC_GPIO_Port GPIOB
#define OLED_DC_Pin GPIO_PIN_10
// CS
#define OLED_CS_GPIO_Port GPIOB
#define OLED_CS_Pin GPIO_PIN_11
//-----------------OLED端口操作定义----------------
/*
#define OLED_CS_Clr() GPIO_ResetBits(GPIOB,OLED_CS)
#define OLED_CS_Set() GPIO_SetBits(GPIOB,OLED_CS)
#define OLED_DC_Clr() GPIO_ResetBits(GPIOB,OLED_DC)
#define OLED_DC_Set() GPIO_SetBits(GPIOB,OLED_DC)
#define OLED_RST_Clr() GPIO_ResetBits(GPIOB,OLED_RST)
#define OLED_RST_Set() GPIO_SetBits(GPIOB,OLED_RST)
*/
#define OLED_RST_Clr() HAL_GPIO_WritePin(OLED_RST_GPIO_Port,OLED_RST_Pin,GPIO_PIN_RESET)//RES
#define OLED_RST_Set() HAL_GPIO_WritePin(OLED_RST_GPIO_Port,OLED_RST_Pin,GPIO_PIN_SET)
#define OLED_DC_Clr() HAL_GPIO_WritePin(OLED_DC_GPIO_Port,OLED_DC_Pin,GPIO_PIN_RESET)//DC
#define OLED_DC_Set() HAL_GPIO_WritePin(OLED_DC_GPIO_Port,OLED_DC_Pin,GPIO_PIN_SET)
#define OLED_CS_Clr() HAL_GPIO_WritePin(OLED_CS_GPIO_Port,OLED_CS_Pin,GPIO_PIN_RESET)//CS
#define OLED_CS_Set() HAL_GPIO_WritePin(OLED_CS_GPIO_Port,OLED_CS_Pin,GPIO_PIN_SET)
//OLED控制用函数
void OLED_WR_Byte(unsigned dat,unsigned cmd);
void OLED_Display_On(void);
void OLED_Display_Off(void);
void OLED_Set_Pos(unsigned char x, unsigned char y);
void OLED_Reset(void);
void OLED_Init_GPIO(void);
void OLED_Init(void);
void OLED_Set_Pixel(unsigned char x, unsigned char y,unsigned char color);
void OLED_Display(void);
void OLED_Clear(unsigned dat);
#endif
oled.c:
#include "oled.h"
#include "stdlib.h"
#include "string.h"
#include "stm32f1xx_hal.h"
#include "spi.h"
//OLED显存总共分为8页
//每页8行，一行128个像素点
//OLED的显存
//存放格式如下.
//[0]0 1 2 3 ... 127 (0~7)行
//[1]0 1 2 3 ... 127 (8~15)行
//[2]0 1 2 3 ... 127 (16~23)行
//[3]0 1 2 3 ... 127 (24~31)行
//[4]0 1 2 3 ... 127 (32~39)行
//[5]0 1 2 3 ... 127 (40~47)行
//[6]0 1 2 3 ... 127 (48~55)行
//[7]0 1 2 3 ... 127 (56~63)行
//数组每个bit存储OLED每个像素点的颜色值(1-亮(白色),0-灭(黑色))
//每个数组元素表示1列8个像素点，一共128列
static unsigned char OLED_buffer[1024] =
{
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
};
/*******************************************************************
* @name :void OLED_WR_Byte(unsigned dat,unsigned cmd)
* @date :2018-08-27
* @function :Write a byte of content to the OLED screen
* @parameters :dat:Content to be written
cmd:0-write command
1-write data
* @retvalue :None
********************************************************************/
uint8_t SPI2_ReadWriteByte(uint8_t TxData)
{
uint8_t rxdata = 1;
#if onlysend //如果只配置了发送 使用HAL_SPI_Transmit
HAL_SPI_Transmit(&hspi2,&TxData,1,100);
//while(HAL_SPI_GetState(&hspi1) == HAL_SPI_STATE_READY);
#else //如果配置了发送和接收 使用HAL_SPI_TransmitReceive
if(HAL_OK == HAL_SPI_TransmitReceive(&hspi2,&TxData,&rxdata,1,100))
{
return rxdata;
};
#endif
return rxdata;
}
void OLED_WR_Byte(unsigned dat,unsigned cmd)
{
if(cmd)
{
OLED_DC_Set();
}
else
{
OLED_DC_Clr();
}
OLED_CS_Clr();
SPI2_ReadWriteByte(dat);
OLED_CS_Set();
}
/*******************************************************************
* @name :void OLED_Set_Pos(unsigned char x, unsigned char y)
* @date :2018-08-27
* @function :Set coordinates in the OLED screen
* @parameters :x:x coordinates
y:y coordinates
* @retvalue :None
********************************************************************/
void OLED_Set_Pos(unsigned char x, unsigned char y)
{
OLED_WR_Byte(YLevel+y/PAGE_SIZE,OLED_CMD);
OLED_WR_Byte((((x+2)&0xf0)>>4)|0x10,OLED_CMD);
OLED_WR_Byte(((x+2)&0x0f),OLED_CMD);
}
/*******************************************************************
* @name :void OLED_Display_On(void)
* @date :2018-08-27
* @function :Turn on OLED display
* @parameters :None
* @retvalue :None
********************************************************************/
void OLED_Display_On(void)
{
OLED_WR_Byte(0X8D,OLED_CMD); //SET DCDC命令
OLED_WR_Byte(0X14,OLED_CMD); //DCDC ON
OLED_WR_Byte(0XAF,OLED_CMD); //DISPLAY ON
}
/*******************************************************************
* @name :void OLED_Display_Off(void)
* @date :2018-08-27
* @function :Turn off OLED display
* @parameters :None
* @retvalue :None
********************************************************************/
void OLED_Display_Off(void)
{
OLED_WR_Byte(0X8D,OLED_CMD); //SET DCDC命令
OLED_WR_Byte(0X10,OLED_CMD); //DCDC OFF
OLED_WR_Byte(0XAE,OLED_CMD); //DISPLAY OFF
}
/*******************************************************************
* @name :void OLED_Set_Pixel(unsigned char x, unsigned char y,unsigned char color)
* @date :2018-08-27
* @function :set the value of pixel to RAM
* @parameters :x:the x coordinates of pixel
y:the y coordinates of pixel
color:the color value of the point
1-white
0-black
* @retvalue :None
********************************************************************/
void OLED_Set_Pixel(unsigned char x, unsigned char y,unsigned char color)
{
if(color)
{
OLED_buffer[(y/PAGE_SIZE)*WIDTH+x]|= (1<<(y%PAGE_SIZE))&0xff;
}
else
{
OLED_buffer[(y/PAGE_SIZE)*WIDTH+x]&= ~((1<<(y%PAGE_SIZE))&0xff);
}
}
/*******************************************************************
* @name :void OLED_Display(void)
* @date :2018-08-27
* @function :Display in OLED screen
* @parameters :None
* @retvalue :None
********************************************************************/
void OLED_Display(void)
{
uint8_t i,n;
for(i=0;i<PAGE_SIZE;i++)
{
OLED_WR_Byte (YLevel+i,OLED_CMD); //设置页地址（0~7）
OLED_WR_Byte (XLevelL,OLED_CMD); //设置显示位置—列低地址
OLED_WR_Byte (XLevelH,OLED_CMD); //设置显示位置—列高地址
for(n=0;n<WIDTH;n++)
{
OLED_WR_Byte(OLED_buffer[i*WIDTH+n],OLED_DATA);
}
} //更新显示
}
/*******************************************************************
* @name :void OLED_Clear(unsigned dat)
* @date :2018-08-27
* @function :clear OLED screen
* @parameters :dat:0-Display full black
1-Display full white
* @retvalue :None
********************************************************************/
void OLED_Clear(unsigned dat)
{
if(dat)
{
memset(OLED_buffer,0,sizeof(OLED_buffer));
}
else
{
memset(OLED_buffer,0xff,sizeof(OLED_buffer));
}
OLED_Display();
}
/*******************************************************************
* @name :void OLED_Reset(void)
* @date :2018-08-27
* @function :Reset OLED screen
* @parameters :dat:0-Display full black
1-Display full white
* @retvalue :None
********************************************************************/
void OLED_Reset(void)
{
OLED_RST_Set();
HAL_Delay(100);
OLED_RST_Clr();
HAL_Delay(100);
OLED_RST_Set();
}
/*******************************************************************
* @name :void OLED_Init_GPIO(void)
* @date :2018-08-27
* @function :Reset OLED screen
* @parameters :None
* @retvalue :None
********************************************************************/
void OLED_Init_GPIO(void)
{
GPIO_InitTypeDef GPIO_InitStructure = {0};
__HAL_RCC_GPIOB_CLK_ENABLE();
HAL_GPIO_WritePin(GPIOB, GPIO_PIN_10|GPIO_PIN_11|GPIO_PIN_12, GPIO_PIN_RESET);//使能B端口时钟
GPIO_InitStructure.Pin = GPIO_PIN_10|GPIO_PIN_11|GPIO_PIN_12; //GPIOB10,11,12
GPIO_InitStructure.Mode = GPIO_MODE_OUTPUT_PP; //推挽输出
GPIO_InitStructure.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(GPIOB, &GPIO_InitStructure);
HAL_GPIO_WritePin(GPIOB, GPIO_PIN_10|GPIO_PIN_11|GPIO_PIN_12, GPIO_PIN_SET);//使能B端口时钟
}
/*******************************************************************
* @name :void OLED_Init(void)
* @date :2018-08-27
* @function :initialise OLED SH1106 control IC
* @parameters :None
* @retvalue :None
********************************************************************/
void OLED_Init(void)
{
OLED_Init_GPIO(); //初始化GPIO
HAL_Delay(200);
OLED_Reset(); //复位OLED
/**************初始化SSD1306*****************/
OLED_WR_Byte(0xAE,OLED_CMD); /*display off*/
OLED_WR_Byte(0x00,OLED_CMD); /*set lower column address*/
OLED_WR_Byte(0x10,OLED_CMD); /*set higher column address*/
OLED_WR_Byte(0x40,OLED_CMD); /*set display start line*/
OLED_WR_Byte(0xB0,OLED_CMD); /*set page address*/
OLED_WR_Byte(0x81,OLED_CMD); /*contract control*/
OLED_WR_Byte(0xFF,OLED_CMD); /*128*/
OLED_WR_Byte(0xA1,OLED_CMD); /*set segment remap*/
OLED_WR_Byte(0xA6,OLED_CMD); /*normal / reverse*/
OLED_WR_Byte(0xA8,OLED_CMD); /*multiplex ratio*/
OLED_WR_Byte(0x3F,OLED_CMD); /*duty = 1/64*/
OLED_WR_Byte(0xC8,OLED_CMD); /*Com scan direction*/
OLED_WR_Byte(0xD3,OLED_CMD); /*set display offset*/
OLED_WR_Byte(0x00,OLED_CMD);
OLED_WR_Byte(0xD5,OLED_CMD); /*set osc division*/
OLED_WR_Byte(0x80,OLED_CMD);
OLED_WR_Byte(0xD9,OLED_CMD); /*set pre-charge period*/
OLED_WR_Byte(0XF1,OLED_CMD);
OLED_WR_Byte(0xDA,OLED_CMD); /*set COM pins*/
OLED_WR_Byte(0x12,OLED_CMD);
OLED_WR_Byte(0xDB,OLED_CMD); /*set vcomh*/
OLED_WR_Byte(0x30,OLED_CMD);
OLED_WR_Byte(0x8D,OLED_CMD); /*set charge pump disable*/
OLED_WR_Byte(0x14,OLED_CMD);
OLED_WR_Byte(0xAF,OLED_CMD); /*display ON*/
}
主函数部分与RTC，I2C基本相同，不再赘述，这里只需在while内部进行更改
// 获取温度
HAL_GPIO_WritePin(GPIOC,GPIO_PIN_13,GPIO_PIN_RESET); // 使用 PC13 引脚上的板载小灯泡进行测试——小灯泡亮
AHT20_Read_CTdata_crc(CT_data); //经过CRC校验，读取AHT20的温度和湿度数据 推荐每隔大于1S读一次
c1 = CT_data[0]*1000/1024/1024; //计算得到湿度值c1(放大了10倍)
t1 = CT_data[1]*2000/1024/1024-500;//计算得到温度值t1(放大了10倍)
//显示温度
GUI_ShowCHinese(15,28,16,"温度",1);
GUI_ShowString(47,28,":",16,1);
GUI_ShowString(62,28,temp,16,1);
GUI_ShowCHinese(96,28,16,(uint8_t)"℃",1);
//显示湿度
GUI_ShowCHinese(15,48,16,"湿度",1);
GUI_ShowString(47,48,":",16,1);
GUI_ShowString(62,48,hum,16,1);
/* Get the RTC current Time */
//HAL_RTC_GetTime(&hrtc, &GetTime, RTC_FORMAT_BIN);
/* Get the RTC current Date */
//HAL_RTC_GetDate(&hrtc, &GetData, RTC_FORMAT_BIN);
//year=2000+ GetData.Year;
//GUI_ShowString(0,0,year,16,1);
//GUI_ShowString(20,0,"/",16,1);
//GUI_ShowString(30,0,GetData.Month,16,1);
//GUI_ShowString(40,0,"/",16,1);
//GUI_ShowString(50,0,GetData.Date,16,1);
//GUI_ShowString(0,20,GetTime.Hours,16,1);
//GUI_ShowString(10,20,":",16,1);
//GUI_ShowString(20,20,GetTime.Minutes,16,1);
//GUI_ShowString(30,20,":",16,1);
//GUI_ShowString(40,20,GetTime.Seconds,16,1);
HAL_Delay(1000);
结果如下：
1976
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
