GD32F450串口DMA收发

Uart0_F450.cpp

#include "UART0_F450.hpp"
#include "main.h"

//#include "usart.h"
//#include "dma.h"

//extern UART_HandleTypeDef huart1;
//extern DMA_HandleTypeDef hdma_usart1_rx;
//extern DMA_HandleTypeDef hdma_usart1_tx;

#define USART0_DATA_ADDRESS      ((uint32_t)&USART_DATA(USART0))

void UART0_F450::Init(uint32_t baud)
{	
	/* initialize clock */
	rcu_periph_clock_enable(RCU_DMA1);
	rcu_periph_clock_enable(RCU_USART0);
	rcu_periph_clock_enable(RCU_GPIOA);
	
	/* initialize port */
	gpio_af_set(GPIOA, GPIO_AF_7, GPIO_PIN_9|GPIO_PIN_10);
	gpio_mode_set(GPIOA, GPIO_MODE_AF, GPIO_PUPD_PULLUP,GPIO_PIN_9|GPIO_PIN_10);
	gpio_output_options_set(GPIOA, GPIO_OTYPE_PP, 
    GPIO_OSPEED_50MHZ,GPIO_PIN_9|GPIO_PIN_10);
	
	/* USART configure */
	usart_deinit(USART0);
	usart_oversample_config(USART0, USART_OVSMOD_8);
	usart_baudrate_set(USART0,baud);			          //波特率
	usart_parity_config(USART0, USART_PM_NONE);		  //校验位:NONE
	usart_word_length_set(USART0, USART_WL_8BIT);		//数据位:8
	usart_stop_bit_set(USART0, USART_STB_1BIT);		  //停止位:1
	usart_receive_config(USART0, USART_RECEIVE_ENABLE);
	usart_transmit_config(USART0, USART_TRANSMIT_ENABLE);
	/* enable USART0 IDLEIE interrupt */
	usart_interrupt_enable(USART0, USART_INT_IDLE);
	/* USART interrupt configuration */
	nvic_irq_enable(USART0_IRQn, 1, 1);
	usart_enable(USART0);
	
	/* USART DMA enable*/
	usart_dma_receive_config(USART0, USART_DENR_ENABLE);
	usart_dma_transmit_config(USART0, USART_DENT_ENABLE);
	
	/*configure DMA0 interrupt*/
	nvic_irq_enable(DMA1_Channel7_IRQn, 0, 0);
    nvic_irq_enable(DMA1_Channel2_IRQn, 0, 1);
	
	dma_single_data_parameter_struct dma_init_struct;
    
	/* deinitialize DMA1 channel7(USART0 tx) */
	dma_single_data_para_struct_init(&dma_init_struct);
	dma_deinit(DMA1, DMA_CH7);
	dma_init_struct.direction = DMA_MEMORY_TO_PERIPH;
	dma_init_struct.memory0_addr = (uint32_t)0;
	dma_init_struct.memory_inc = DMA_MEMORY_INCREASE_ENABLE;
	dma_init_struct.periph_memory_width = DMA_PERIPH_WIDTH_8BIT;
	dma_init_struct.number = 0;
	dma_init_struct.periph_addr = USART0_DATA_ADDRESS;
	dma_init_struct.periph_inc = DMA_PERIPH_INCREASE_DISABLE;
	dma_init_struct.priority = DMA_PRIORITY_ULTRA_HIGH;
	dma_single_data_mode_init(DMA1, DMA_CH7, &dma_init_struct);
	
	/* configure DMA mode */
	dma_circulation_disable(DMA1, DMA_CH7);
	dma_channel_subperipheral_select(DMA1, DMA_CH7, DMA_SUBPERI4);
	/* enable DMA1 channel7 transfer complete interrupt */
	dma_interrupt_enable(DMA1, DMA_CH7, DMA_CHXCTL_FTFIE);
	/* enable DMA1 channel7 */
	dma_channel_enable(DMA1, DMA_CH7);

	/* deinitialize DMA1 channel2 (USART0 rx) */
	dma_deinit(DMA1, DMA_CH2);
	dma_init_struct.direction = DMA_PERIPH_TO_MEMORY;
	dma_init_struct.memory0_addr = (uint32_t)RxBuf;
	dma_init_struct.memory_inc = DMA_MEMORY_INCREASE_ENABLE;
	dma_init_struct.number = 128;
	dma_init_struct.periph_addr = (uint32_t)&USART_DATA(USART0);
	dma_init_struct.periph_inc = DMA_PERIPH_INCREASE_DISABLE;
	dma_init_struct.periph_memory_width = DMA_PERIPH_WIDTH_8BIT;
	dma_init_struct.priority = DMA_PRIORITY_ULTRA_HIGH;
	dma_single_data_mode_init(DMA1, DMA_CH2, &dma_init_struct);
	
	/* configure DMA mode */
	dma_circulation_disable(DMA1, DMA_CH2);
	dma_channel_subperipheral_select(DMA1, DMA_CH2, DMA_SUBPERI4);
	/* enable DMA1 channel2 transfer complete interrupt */
	dma_interrupt_enable(DMA1, DMA_CH2, DMA_CHXCTL_FTFIE);
	/* enable DMA1 channel2 */
	dma_channel_enable(DMA1, DMA_CH2);
}
uint8_t UART0_F450::Write(uint8_t *buf, uint16_t len)
{
	dma_single_data_parameter_struct dma_init_struct;
	
	dma_single_data_para_struct_init(&dma_init_struct);
	dma_deinit(DMA1, DMA_CH7);
	dma_init_struct.direction = DMA_MEMORY_TO_PERIPH;
	dma_init_struct.memory0_addr = (uint32_t)buf;
	dma_init_struct.memory_inc = DMA_MEMORY_INCREASE_ENABLE;
	dma_init_struct.periph_memory_width = DMA_PERIPH_WIDTH_8BIT;
	dma_init_struct.number = len;
	dma_init_struct.periph_addr = USART0_DATA_ADDRESS;
	dma_init_struct.periph_inc = DMA_PERIPH_INCREASE_DISABLE;
	dma_init_struct.priority = DMA_PRIORITY_ULTRA_HIGH;
	dma_single_data_mode_init(DMA1, DMA_CH7, &dma_init_struct);
	dma_channel_subperipheral_select(DMA1, DMA_CH7, DMA_SUBPERI4);
	dma_channel_enable(DMA1, DMA_CH7);
	while(!dma_flag_get(DMA1,DMA_CH7,DMA_FLAG_FTF));
}
uint16_t UART0_F450::GetRxLenth(void)
{
	return 128 - dma_transfer_number_get(DMA1, DMA_CH2);
}
void UART0_F450::ReadResume(void)
{
	dma_single_data_parameter_struct dma_init_struct;
	/* deinitialize DMA channel2 (USART0 rx) */
	dma_deinit(DMA1, DMA_CH2);
	dma_init_struct.direction = DMA_PERIPH_TO_MEMORY;
	dma_init_struct.memory0_addr = (uint32_t)RxBuf;
	dma_init_struct.memory_inc = DMA_MEMORY_INCREASE_ENABLE;
	dma_init_struct.number = 128;
	dma_init_struct.periph_addr = (uint32_t)&USART_DATA(USART0);
	dma_init_struct.periph_inc = DMA_PERIPH_INCREASE_DISABLE;
	dma_init_struct.periph_memory_width = DMA_PERIPH_WIDTH_8BIT;
	dma_init_struct.priority = DMA_PRIORITY_ULTRA_HIGH;
	dma_single_data_mode_init(DMA1, DMA_CH2, &dma_init_struct);
	/* configure DMA mode */
	dma_circulation_disable(DMA1, DMA_CH2);
	dma_channel_subperipheral_select(DMA1, DMA_CH2, DMA_SUBPERI4);
	/* enable DMA channel2 */
	dma_channel_enable(DMA1, DMA_CH2);
}
void UART0_F450::Read(uint8_t *buf, uint16_t *len)
{
	*len = 128 - dma_transfer_number_get(DMA1, DMA_CH2);
	if(*len > 0)
	{
		for(int i = 0; i < *len; i++)
		{
			buf[i] = RxBuf[i];
		}
		dma_single_data_parameter_struct dma_init_struct;
	/* deinitialize DMA channel2 (USART0 rx) */
	dma_deinit(DMA1, DMA_CH2);
	dma_init_struct.direction = DMA_PERIPH_TO_MEMORY;
	dma_init_struct.memory0_addr = (uint32_t)RxBuf;
	dma_init_struct.memory_inc = DMA_MEMORY_INCREASE_ENABLE;
	dma_init_struct.number = 128;
	dma_init_struct.periph_addr = (uint32_t)&USART_DATA(USART0);
	dma_init_struct.periph_inc = DMA_PERIPH_INCREASE_DISABLE;
	dma_init_struct.periph_memory_width = DMA_PERIPH_WIDTH_8BIT;
	dma_init_struct.priority = DMA_PRIORITY_ULTRA_HIGH;
	dma_single_data_mode_init(DMA1, DMA_CH2, &dma_init_struct);
	/* configure DMA mode */
	dma_circulation_disable(DMA1, DMA_CH2);
	dma_channel_subperipheral_select(DMA1, DMA_CH2, DMA_SUBPERI4);
	/* enable DMA channel2 */
	dma_channel_enable(DMA1, DMA_CH2);
	}
}
void UART0_F450::Write(uint16_t len)
{
	dma_single_data_parameter_struct dma_init_struct;
	
	dma_single_data_para_struct_init(&dma_init_struct);
	dma_deinit(DMA1, DMA_CH7);
	dma_init_struct.direction = DMA_MEMORY_TO_PERIPH;
	dma_init_struct.memory0_addr = (uint32_t)TxBuf;
	dma_init_struct.memory_inc = DMA_MEMORY_INCREASE_ENABLE;
	dma_init_struct.periph_memory_width = DMA_PERIPH_WIDTH_8BIT;
	dma_init_struct.number = len;
	dma_init_struct.periph_addr = USART0_DATA_ADDRESS;
	dma_init_struct.periph_inc = DMA_PERIPH_INCREASE_DISABLE;
	dma_init_struct.priority = DMA_PRIORITY_ULTRA_HIGH;
	dma_single_data_mode_init(DMA1, DMA_CH7, &dma_init_struct);
	dma_channel_enable(DMA1, DMA_CH7);
	while(RESET == dma_flag_get(DMA1, DMA_CH7, DMA_FLAG_FTF));
}
int16_t UART0_F450::Read(void)
{
	return 1;
}	

UART0_F450.hpp

#pragma once

#include <stdint.h>

#include "Bsp/bsp.hpp"

class UART0_F450: public UART
{
public:
	UART0_F450(){}
	void Init(uint32_t baud = 115200);
	uint8_t Write(uint8_t *buf, uint16_t len);
	void Read(uint8_t *buf, uint16_t *len);
	void Write(uint16_t len);
	void ReadResume(void);
	int16_t Read(void);  
	uint16_t GetRxLenth(void);		
};

main.h

/* USER CODE BEGIN Header */
/**
  ******************************************************************************
  * @file           : main.h
  * @brief          : Header for main.c file.
  *                   This file contains the common defines of the application.
  ******************************************************************************
  * @attention
  *
  * Copyright (c) 2022 STMicroelectronics.
  * All rights reserved.
  *
  * This software is licensed under terms that can be found in the LICENSE file
  * in the root directory of this software component.
  * If no LICENSE file comes with this software, it is provided AS-IS.
  *
  ******************************************************************************
  */
/* USER CODE END Header */

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __MAIN_H
#define __MAIN_H

//#include "bsp.hpp"
//#include "os.hpp"




//extern BSP *gbsp;
//extern OS *gos;

#ifdef __cplusplus
extern "C" {
#endif

	
/* Includes ------------------------------------------------------------------*/
#include "gd32f4xx.h"
#include "gd32f4xx_gpio.h"
#include "gd32f4xx.h"
#include "gd32f4xx_dma.h"
#include "system_gd32f4xx.h"
#include "gd32f4xx_rcu.h"
 	




	

/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */

/* USER CODE END Includes */

/* Exported types ------------------------------------------------------------*/
/* USER CODE BEGIN ET */

/* USER CODE END ET */

/* Exported constants --------------------------------------------------------*/
/* USER CODE BEGIN EC */

/* USER CODE END EC */

/* Exported macro ------------------------------------------------------------*/
/* USER CODE BEGIN EM */
/* USER CODE END EM */

/* Exported functions prototypes ---------------------------------------------*/
//void Error_Handler(void);

/* USER CODE BEGIN EFP */

/* USER CODE END EFP */

/* Private defines -----------------------------------------------------------*/

/* USER CODE BEGIN Private defines */

/* USER CODE END Private defines */

#ifdef __cplusplus
}
#endif

#endif /* __MAIN_H */