iPhone底接口定义

看看这2个链接

http://bbs.weiphone.com/read.php?tid=25991

http://www.allpinouts.org/index.php/Apple_iPod_-_iPhone_dock

Connector pinout for: Apple iPod - iPhone dock




30 pin connector used on the dock station for iPod and iPhone.
Available in all Apple iPod MP3 player (iPod 1G, 2G, 3G, 4G, 5G and Nano).


This connector is used on iPod (starting from 3rd generation) and iPhone. It is used to connect the iPod or iPhone to various devices: PC (via USB or FireWire IEEE1394), audio amplifier, serial device (controlled via the Apple Accessory Protocol).




Pin  Signal  Description  
1  GND  Ground (-), internaly connected with Pin 2 on iPod motherboard  
2  GND  Audio and Video ground (-), internaly connected with Pin 2 on iPod motherboard  
3  Right  Line Out - R (+) (Audio output, right channel)  
4  Left  Line Out - L(+) (Audio output, left channel)  
5  Right In  Line In - R (+)  
6  Left In  Line In - L (+)  
8  Video Out  Composite video output (only when the slideshow mode is active on iPod Photo)  
9  S-Video Chrominance output  for iPod Color, Photo only  
10  S-Video Luminance output  for iPod Color, Photo only  
11  GND  Serial GND  
12  Tx  ipod sending line, Serial TxD  
13  Rx  ipod receiving line, Serial RxD  
14  NC  
15  GND  Ground (-), internaly connected with pin 16 on iPod motherboard  
16  GND  USB GND (-), internaly connected with pin 15 on iPod motherboard  
17  NC  
18  3.3V  3.3V Power (+)
Stepped up to provide +5 VDC to USB on iPod Camera Connector.
If iPod is put to sleep while Camera Connector is present, +5 VDC at this pin slowly drains back to 0 VDC.  
19,20  +12V  Firewire Power 12 VDC (+)  
21  Accessory Indicator/Serial enable  Different resistances indicate accessory type:

1KOhm - iPod docking station, beeps when connected

10KOhm - Takes some iPods into photo import mode

500KOhm - related to serial communication / used to enable serial communications Used in Dension Ice Link Plus car interface

1MOhm - Belkin auto adaptor, iPod shuts down automatically when power disconnected Connecting pin 21 to ground with a 1MOhm resistor does stop the ipod when power (i.e. Firewire-12V) is cut. Looks to be that when this pin is grounded it closes a switch so that on loss of power the Ipod shuts off. Dock has the same Resistor.

22  TPA (-)  FireWire Data TPA (-)  
23  5 VDC (+)  USB Power 5 VDC (+)  
24  TPA (+)  FireWire Data TPA (+)  
25  Data (-)  USB Data (-)  
26  TPB (-)  FireWire Data TPB (-)  
27  Data (+)  USB Data (+)
Pins 25 and 27 may be used in different manner. To force the iPod 5G to charge in any case, when 'USB Power 5 VDC' (pin 23) is fed, 25 must be connected to 5V through a 10KOhm resistor, and 27 must be connected to the Ground (for example: pin 1) with a 10KOhm resistor.  
28  TPB (+)  FireWire Data TPB (+)  
29,30  GND  FireWire Ground (-)  




Notes
Signals with grey background may not exist on some docking stations.
Apple serial devices (i.e. iTalk and remote control) communicate with iPod (3rd generation or more) using the Apple Accessory Protocol.
The serial connection uses a standard 19200 baud 8N1 protocol (the speed can be increased up to 57600 but tends to become unstable).