STM32L073RZ进行两路AD电压信号采集(非DMA方式)

使用STM32L073RZ调试两路AD电压信号采集，刚开始用DMA方式，发现开启DMA转换USB虚拟串口无法识别。现在想不通过DMA方式来进行两路AD电压信号采集。单路读取方法为
aADCxConvertedData = HAL_ADC_GetValue(&hadc);
两路AD电压信号采集（非DMA方式）为：使用非连续转换，每次配置某个通道 、然后启动ADC，读取数据；再开启另一通道，启动ADC，读取数据。
部分程序为：

static uint16_t   aADCxConvertedData[2];
static void MX_ADC_Init(void)
{
  hadc.Instance = ADC1;
  hadc.Init.OversamplingMode = DISABLE;
  hadc.Init.ClockPrescaler = ADC_CLOCK_SYNC_PCLK_DIV1;
  hadc.Init.Resolution = ADC_RESOLUTION_12B;
  hadc.Init.SamplingTime = ADC_SAMPLETIME_1CYCLE_5;
  hadc.Init.ScanConvMode = ADC_SCAN_DIRECTION_FORWARD;
  hadc.Init.DataAlign = ADC_DATAALIGN_RIGHT;
  hadc.Init.ContinuousConvMode = DISABLE;
  hadc.Init.DiscontinuousConvMode = ENABLE;
  hadc.Init.ExternalTrigConvEdge = ADC_EXTERNALTRIGCONVEDGE_NONE;
  hadc.Init.DMAContinuousRequests = DISABLE;
  hadc.Init.EOCSelection = ADC_EOC_SINGLE_CONV;
  hadc.Init.Overrun = ADC_OVR_DATA_PRESERVED;
  hadc.Init.LowPowerAutoWait = DISABLE;
  hadc.Init.LowPowerFrequencyMode = DISABLE;
  hadc.Init.LowPowerAutoPowerOff = DISABLE;
  if (HAL_ADC_Init(&hadc) != HAL_OK)
  {
    Error_Handler();
  }

    /**Configure for the selected ADC regular channel to be converted. 
    */
//  sConfig.Channel = ADC_CHANNEL_8;
//  sConfig.Rank = ADC_RANK_CHANNEL_NUMBER;
//  if (HAL_ADC_ConfigChannel(&hadc, &sConfig) != HAL_OK)
//  {
//    Error_Handler();
//  }

//    /**Configure for the selected ADC regular channel to be converted. 
//    */
//  sConfig.Channel = ADC_CHANNEL_9;
//  if (HAL_ADC_ConfigChannel(&hadc, &sConfig) != HAL_OK)
//  {
//    Error_Handler();
//  }

}
int main(void)
{
  HAL_Init();
/* Configure the system clock */
  SystemClock_Config();
  BSP_LED_Init();
  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  MX_ADC_Init();
  while (1)
  {
     sConfig.Channel = ADC_CHANNEL_8;
     sConfig.Rank = ADC_RANK_CHANNEL_NUMBER;
    if (HAL_ADC_ConfigChannel(&hadc, &sConfig) != HAL_OK)
       {
        Error_Handler();
       }
    if (HAL_ADC_Start(&hadc) != HAL_OK)
      {
        Error_Handler();
      }
    aADCxConvertedData[0] = HAL_ADC_GetValue(&hadc);

   sConfig.Channel = ADC_CHANNEL_9;
   if (HAL_ADC_ConfigChannel(&hadc, &sConfig) != HAL_OK)
      {
        Error_Handler();
      }
   if (HAL_ADC_Start(&hadc) != HAL_OK)
     {
        Error_Handler();
     }              
   aADCxConvertedData[1] = HAL_ADC_GetValue(&hadc);
  }
}