[更改挂载点]重新挂载硬盘

 显示磁盘空间使用情况

df -h

 df -h 命令的输出显示了文件系统的磁盘空间使用情况。

这里 /dev/nvme0n1p1 设备（大小为 880GB）已经被挂载到 /media/nvidia/SSD 目录下，并且使用了 304GB，剩余 532GB，使用率为 37%。这意味着 /dev/nvme0n1 已经被格式化并且在使用中，挂载点是 /media/nvidia/SSD。

如果你想重新格式化 /dev/nvme0n1p1，首先需要卸载这个挂载点。可以使用以下命令卸载：

umount /media/nvidia/SSD

在卸载之后，你就可以安全地格式化这个设备了。再次运行 mkfs -t ext4 /dev/nvme0n1p1 来创建新的 ext4 文件系统。但请注意，这将删除该设备上的所有数据。

sudo mkfs -t ext4 /dev/nvme0n1

./copy_rootfs.sh /dev/xxx，xxx为外部存储设备
把nvme_config.sh文件copy到设备中
chmod +x给脚本文件添加可执行权限
执行sudo ./nvme_config.sh
重启设备
系统启动后后，执行df -h观察/目录是否在外部存储介质中

---

copy_rootfs.sh文件

#!/bin/bash

parted_dev=""
mount_dev=""
umount_dev=""

function Usag()
{
	echo "usag: "
	echo "     copy_rootfs.sh /dev/sda"
	echo "     copy_rootfs.sh /dev/nvme0n1"
	echo "     copy_rootfs.sh /dev/mmcblk0"
}

if [ $# -ne 1 ];then
	Usag
	exit
fi

if [[ $1 =~ "/dev/sd" ]];then
	parted_dev="$1"
        mount_dev="$11"
elif [[ $1 =~ "/dev/nvme0n1" ]];then
	parted_dev="$1"
        mount_dev="$1p1"
elif [[ $1 =~ "/dev/mmcblk" ]];then
	parted_dev="$1"
        mount_dev="$1p1"
else
	Usag
	exit
fi

umount_dev=`ls $parted_dev*`
for var in $umount_dev
do
	echo "nvidia" | sudo -S umount $var
done

echo "nvidia" | sudo -S parted -s $parted_dev mklabel gpt;
if [ $? -ne 0 ];then
	echo "error: mklable gpt."
	exit
fi

echo "nvidia" | sudo -S parted -s $parted_dev mkpart primary 2048s 100%;
if [ $? -ne 0 ];then
	echo "error: mkpart primary."
	exit
fi

echo "nvidia" | sudo -S mkfs.ext4 -F $mount_dev;
if [ $? -ne 0 ];then
	echo "error: mkfs.ext4."
	exit
fi

echo "nvidia" | sudo -S mount $mount_dev /mnt;
if [ $? -ne 0 ];then
	echo "error: mount"
	exit
fi

echo "nvidia" | sudo -S rsync -aAXv / --exclude={"/dev/","/proc/","/sys/","/tmp/","/run/user/","/mnt/","/media/*","/lost+found"} /mnt;
if [ $? -ne 0 ];then
	echo "error: rsync error, pleas check file"
	exit
fi

echo "nvidia" | sudo -S umount $mount_dev
if [ $? -ne 0 ];then
	echo "error: umount"
	exit
fi

exit

nvme_config.sh文件

#!/bin/bash
sudo mv /boot/extlinux/extlinux.conf /boot/extlinux/extlinux.conf.b
cat >> /boot/extlinux/extlinux.conf << HERE
TIMEOUT 30
DEFAULT primary

MENU TITLE L4T boot options

LABEL primary
      MENU LABEL primary kernel
      LINUX /boot/Image
      #FDT /boot/dtb/kernel_tegra234-p3701-0004-p3737-0000.dtb
      INITRD /boot/initrd
      APPEND ${cbootargs} root=/dev/nvme0n1p1 rw rootwait rootfstype=ext4 mminit_loglevel=8 console=ttyTCU0,115200 console=ttyAMA0,115200 console=tty0 firmware_class.path=/etc/firmware fbcon=map:0 net.ifnames=0 

# When testing a custom kernel, it is recommended that you create a backup of
# the original kernel and add a new entry to this file so that the device can
# fallback to the original kernel. To do this:
#
# 1, Make a backup of the original kernel
#      sudo cp /boot/Image /boot/Image.backup
#
# 2, Copy your custom kernel into /boot/Image
#
# 3, Uncomment below menu setting lines for the original kernel
#
# 4, Reboot

# LABEL backup
#    MENU LABEL backup kernel
#    LINUX /boot/Image.backup
#    FDT /boot/dtb/kernel_tegra234-p3701-0004-p3737-0000.dtb
#    INITRD /boot/initrd
#    APPEND ${cbootargs}
HERE