HCIP第二次实验

配置路由接口及R5环回

接着在私网边界路由器配一条缺省指向isp
[R1]ip route-static 0.0.0.0 0 15.0.0.2[R2]ip route-static 0.0.0.0 0 25.0.0.2

[R3]ip route-static 0.0.0.0 0 35.0.0.2[R4]ip route-static 0.0.0.00 45.0.0.2

然后配置R1与R5之间的pap认证，R5为主认证方

R2同理

接下来R3和R5之间使用HDLC封装
[R5]int s4/0/0
[R5-Serial4/0/0]link-protocol hdlc
Warning: The encapsulation protocol of the link will be changed. Continue? [YIN]:y
[R3]int s4/0/0
[R3-Serial4/0/O]link-protocol hdlc
Warning: The encapsulation protocol of the link will be changed.Continue? [YIN]:y
在R3上ping 35.0.0.2,成功则配置完成

 R1，R2，R3构建MGRE环境，以R1为中心站点

然后是R1,R4之间点到点的GRE

[R1]int t0/0/1
[R1-Tunnel0/0/1]ip add 192.168.6.1 24
[R1-Tunnel0/0/1]tunnel-protocol gre
[R1-Tunnel0/0/1]source 15.0.0.1
[R1-Tunnel0/0/1]description 45.0.0.1

[R4]int t0/0/0
[R4-Tunnel0/0/0]ip add 192.168.6.2 24
[R4-Tunnel0/0/0]tunnel-protocol gre 
[R4-Tunnel0/0/0]source 45.0.0.1   
[R4-Tunnel0/0/0]description 15.0.0.1

接着，整个私有网络基于RIP全网可达

[R1]rip
[R1-rip-1]version 2
[R1-rip-1]network 192.168.1.0
[R1-rip-1]network 192.168.5.0
[R1-rip-1]network 192.168.6.0
R2,R3,R4也同理

[R2-rip-1]network 192.168.2.0
[R2-rip-1]network 192.168.5.0

[R3-rip-1]network 192.168.5.0
[R3-rip-1]network 192.168.3.0

[R4-rip-1]network 192.168.4.0
[R4-rip-1]network 192.168.6.0

然后给所有pc手动配ip

最后在边界路由上配置低级ACL，使pc可以访问R5（ISP）环回

[R1]acl 2000
[R1-acl-basic-2000]rule permit source 192.168.1.0 0.0.0.255
[R1-acl-basic-2000]q
[R1]int s4/0/0
[R1-Serial4/0/0]nat outbound 2000

[R2]acl 2000
[R2-acl-basic-2000]rule permit source 192.168.2.0 0.0.0.255
[R2-acl-basic-2000]q
[R2]int s4/0/0
[R2-Serial4/0/0]nat outbound 2000

[R3]acl 2000
[R3-acl-basic-2000]rule permit source 192.168.3.0 0.0.0.255
[R3-acl-basic-2000]q
[R3]int s4/0/0
[R3-Serial4/0/0]nat outbound 2000

[R4]acl 2000
[R4-acl-basic-2000]rule permit source 192.168.4.0 0.0.0.255
[R4-acl-basic-2000]q
[R4]int g0/0/1
[R4-GigabitEthernet0/0/1]nat outbound 2000

配置完成后所有pc都可以ping通R5环回