静态路由综合实验

一、实验拓扑图

二、实验需求

1、R6为ISP，接口IP地址均为公有地址，该设备只能配置IP地址，之后不能再对其进行任何配置；
2、R1-R5为局域网，私有IP地址192.168.1.0/24，请合理分配；
3、R1、R2、R4，各有两个环回IP地址；R5、R6各有一个环回地址；所有路由器上环回均代表连接用户的接口；
4、R3下面的两台PC通过DHCP自动获取IP地址；
5、选路最佳，路由尽量小，避免环路；
6、R1-R5均可以访问R6的环回；
7、在R1上配置telnet服务，使R6能通过R5的共有地址telnet到R1上；
8、R4与R5正常通过1000M链路，故障时通过100M链路；

三、实验思路

1. 划分IP，给相应设备配IP地址。
2. 配置DHCP，使R3下面的两台PC通过DHCP自动获取IP地址

3、编写除了到达1.0.0.0/24之外，到达其他网段的静态路由。

4、配置缺省路由，实现到1.0.0.0/24互通。此时实现内网通；在R5路由器上配置nat，可用esay ip ，此时实现全网通

5、做汇总，做防环，做黑洞路由配置

6、做备份，通过改变路由条目优先级实现

7、测试，观察1000Mb/s链路故障时，数据能否走100Mb/s链路

8、R6 telnet R5的公有地址时，实际登录到R1上，在R1上配置telnet服务时，通过nat server发布到R5的公网接口

四、实验步骤

1、配置IP地址

[R1]int g0/0/0

[R1-GigabitEthernet0/0/0]ip add 192.168.1.1 30

[R1-GigabitEthernet0/0/0]int g0/0/1

[R1-GigabitEthernet0/0/1]ip add 192.168.1.5 30

[R1]int l0

[R1-LoopBack0]ip add 192.168.1.33 28

[R1-LoopBack0]int l1

[R1-LoopBack1]ip add 192.168.1.49 28

[R2]int g0/0/0

[R2-GigabitEthernet0/0/0]ip add 192.168.1.2 30

[R2-GigabitEthernet0/0/0]int g0/0/1

[R2-GigabitEthernet0/0/1]ip add 192.168.1.9 30

[R2]int l0

[R2-LoopBack0]ip add 192.168.1.65 28

[R2-LoopBack0]int l1

[R2-LoopBack1]ip add 192.168.1.81 28

[R3]int g0/0/0

[R3-GigabitEthernet0/0/0]ip add 192.168.1.6 30

[R3-GigabitEthernet0/0/0]int g0/0/1

[R3-GigabitEthernet0/0/1]ip add 192.168.1.13 30

[R3-GigabitEthernet0/0/1]int g0/0/2

[R3-GigabitEthernet0/0/2]ip add 192.168.1.97 27

[R4]int g0/0/0

[R4-GigabitEthernet0/0/0]ip add 192.168.1.10 30

[R4-GigabitEthernet0/0/0]int g0/0/1

[R4-GigabitEthernet0/0/1]ip add 192.168.1.14 30

[R4-GigabitEthernet0/0/1]int g0/0/2

[R4-GigabitEthernet0/0/2]ip add 192.168.1.17 30

[R4]int g4/0/0

[R4-GigabitEthernet4/0/0]ip add 192.168.1.21 30

[R4]int l0

[R4-LoopBack0]ip add 192.168.1.129 28

[R4-LoopBack0]int l1

[R4-LoopBack1]ip add 192.168.1.145 28

[R5]int g0/0/0

[R5-GigabitEthernet0/0/0]ip add 192.168.1.18 30

[R5-GigabitEthernet0/0/0]int g0/0/1

[R5-GigabitEthernet0/0/1]ip add 12.0.0.5 24

[R5]int l0

[R5-LoopBack0]ip add 192.168.1.161 27

[R6]int g0/0/0

[R6-GigabitEthernet0/0/0]ip add 12.0.0.6 24

[R6-GigabitEthernet0/0/0]int loopBack 0

[R6-LoopBack0]ip add 1.0.0.6 24

2、配置R3的DHCP

[R3]dhcp enable

[R3]ip pool aa

[R3-ip-pool-aa]net 192.168.1.96 mask 27

[R3-ip-pool-aa]gateway-list 192.168.1.97

[R3-ip-pool-aa]dns-list 114.114.114.114 8.8.8.8

[R3]int g0/0/2

[R3-GigabitEthernet0/0/2]dhcp select global

3、配置除了到达1.0.0.0/24之外的静态路由

[R1]ip route-static 192.168.1.64 27 192.168.1.2

[R1]ip route-static 192.168.1.8 30 192.168.1.2

[R1]ip route-static 192.168.1.96 27 192.168.1.6

[R1]ip route-static 192.168.1.12 30 192.168.1.6

[R1]ip route-static 192.168.1.16 30 192.168.1.2

[R1]ip route-static 192.168.1.20 30 192.168.1.2

[R1]ip route-static 192.168.1.16 30 192.168.1.6

[R2]ip route-static 192.168.1.128 27 192.168.1.10

[R2]ip route-static 192.168.1.16 30 192.168.1.10

[R2]ip route-static 192.168.1.20 30 192.168.1.10

[R2]ip route-static 192.168.1.12 30 192.168.1.10

[R2]ip route-static 192.168.1.96 27 192.168.1.10

[R2]ip route-static 192.168.1.96 27 192.168.1.1

[R2]ip route-static 192.168.1.4 30 192.168.1.1

[R2]ip route-static 192.168.1.32 27 192.168.1.1

[R2]ip route-static 192.168.1.160 27 192.168.1.10

[R3]ip route-static 192.168.1.32 27 192.168.1.5

[R3]ip route-static 192.168.1.0 30 192.168.1.5

[R3]ip route-static 192.168.1.64 27 192.168.1.5

[R3]ip route-static 192.168.1.64 27 192.168.1.14

[R3]ip route-static 192.168.1.8 30 192.168.1.14

[R3]ip route-static 192.168.1.128 27 192.168.1.14

[R3]ip route-static 192.168.1.16 30 192.168.1.14

[R3]ip route-static 192.168.1.20 30 192.168.1.14

[R3]ip route-static 192.168.1.160 27 192.168.1.14

[R4]ip route-static 192.168.1.64 27 192.168.1.9

[R4]ip route-static 192.168.1.0 30 192.168.1.9

[R4]ip route-static 192.168.1.32 27 192.168.1.9

[R4]ip route-static 192.168.1.32 27 192.168.1.13

[R4]ip route-static 192.168.1.4 30 192.168.1.13

[R4]ip route-static 192.168.1.96 27 192.168.1.13

[R4]ip route-static 192.168.1.160 27 192.168.1.18

[R4]ip route-static 192.168.1.160 27 192.168.1.22

[R5]ip route-static 192.168.1.96 27 192.168.1.17

[R5]ip route-static 192.168.1.4 30 192.168.1.17

[R5]ip route-static 192.168.1.32 27 192.168.1.17

[R5]ip route-static 192.168.1.0 30 192.168.1.17

[R5]ip route-static 192.168.1.64 27 192.168.1.17

[R5]ip route-static 192.168.1.8 30 192.168.1.17

[R5]ip route-static 192.168.1.12 30 192.168.1.17

[R5]ip route-static 192.168.1.128 27 192.168.1.21

[R5]ip route-static 192.168.1.96 27 192.168.1.21

[R5]ip route-static 192.168.1.4 30 192.168.1.21

[R5]ip route-static 192.168.1.32 27 192.168.1.21

[R5]ip route-static 192.168.1.0 30 192.168.1.21

[R5]ip route-static 192.168.1.64 27 192.168.1.21

[R5]ip route-static 192.168.1.8 30 192.168.1.21

[R5]ip route-static 192.168.1.12 30 192.168.1.21

4、配置全网通

（1）配置缺省路由，实现1.0.0.0/24互通。此时实现内网通

[R1]ip route-static 0.0.0.0 0 192.168.1.2

[R1]ip route-static 0.0.0.0 0 192.168.1.6

[R2]ip route-static 0.0.0.0 0 192.168.1.10

[R3]ip route-static 0.0.0.0 0 192.168.1.14

[R4]ip route-static 0.0.0.0 0 192.168.1.18

[R4]ip route-static 0.0.0.0 0 192.168.1.22

[R5]ip route-static 0.0.0.0 0 12.0.0.6

（2）在R5路由器上配置nat

[R5]acl 2000

[R5-acl-basic-2000]rule permit source 192.168.1.0 0.0.0.225

[R5-acl-basic-2000]int g0/0/1

[R5-GigabitEthernet0/0/1]nat outbound 2000

5、防环，做黑洞路由配置

[R1]ip route-static 192.168.1.32 27 NULL 0

[R2]ip route-static 192.168.1.64 27 NULL 0

[R4]ip route-static 192.168.1.128 27 NULL 0

6、做备份

[R4]ip route-static 0.0.0.0 0 192.168.1.22 preference 61

[R5]ip route-static 192.168.1.0 255.255.255.252 192.168.1.21 preference 61

[R5]ip route-static 192.168.1.4 255.255.255.252 192.168.1.21 preference 61

[R5]ip route-static 192.168.1.8 255.255.255.252 192.168.1.21 preference 61.

[R5]ip route-static 192.168.1.12 255.255.255.252 192.168.1.21 preference 61

[R5]ip route-static 192.168.1.32 255.255.255.252 192.168.1.21 preference 61

[R5]ip route-static 192.168.1.32 255.255.255.254 192.168.1.21 preference 61

[R5]ip route-static 192.168.1.32 255.255.255.224 192.168.1.21 preference 61

[R5]ip route-static 192.168.1.64 255.255.255.224 192.168.1.21 preference 61

[R5]ip route-static 192.168.1.96 255.255.255.224 192.168.1.21 preference 61

[R5]ip route-static 192.168.1.128 255.255.255.224 192.168.1.21 preference 61

7、[R1]telnet server enable

  [R1]aaa

  [R1-aaa]local-user wangdaye password cipher wdy12345 privilege level 15

  [R1-aaa]local-user wangdaye service-type telnet

  [R1]user-interface vty 0 4

  [R1-ui-vty0-4]authentication-mode aaa

 [R5]int g0/0/1

 [R5-GigabitEthernet0/0/1]nat server protocol tcp global current-interface 23 inside 192.168.1.1   23

Waring:The port 23 is well-known port. If you continue it may cause function failure

Are you sure to continue?[Y/N]:y