hi3516a的uboot、kernel及文件系统的烧录

1.Windows和Linux主机间文件传输：
通过smb方式在Windows下登录Linux虚拟主机
step1 Linux下root用户登录
step2 开启smb服务：service smb start
step3 Windows运行中：\ \192.168.1.2（虚拟机ip）
【注】主机和虚拟机ip在同一网段

2.用海思自带的烧录工具FastBoot3.1(BVT)进行烧录
使用模式：Burn by Partition
step1 制作*.xml文件（用于保存自己的配置信息）
这里命名为hi3516a_partition_table.xml
step2 连接hi3516a开发板的网口和串口到PC端相应位置
step3 设置相应参数，如：
Serial Port——COM4
Server IP——192.168.1.67（PC的ip）
Mac Address——自动生成
IP Address——192.168.1.10（开发板）
Subnet Mask——255.255.255.0（与主PC一致）
Gateway——192.168.1.1（与PC一致）
step4 Burn
【注】烧录时要将u-boot、uImage及*.yaffs文件与FastBoot3.1(BVT)放在同一目录下

3.烧录成功时串口打印文件
【ComLog】
U-Boot 2010.06 (Aug 14 2017 - 17:33:31)
NAND: Check nand flash controller v610. found
Special NAND id table Version 1.36
Nand ID: 0x2C 0xDA 0x90 0x95 0x06 0x00 0x00 0x00
Block:128KB Page:2KB Chip:256MB*1 OOB:64B ECC:4bit/512
256 MiB
Check spi flash controller v350… Found
Can’t find a valid spi flash chip.
Can’t find a valid spi flash chip.
*** Warning - bad CRC or NAND, using default environment

In: serial
Out: serial
Err: serial
start download process.
version: 3.0.3
(OK)

nand
(OK)

Check spi flash controller v350… Found
Can’t find a valid spi flash chip.
Can’t find a valid spi flash chip.
no find spi
(OK)

Block:128KB Chip:256MB*1 Page:2KB OOB:64B ECC:4bits/512Byte
ID:0x2C 0xDA 0x90 0x95 0x06 0x00 0x00 0x00
Name:“NAND 256MiB 3,3”
(OK)

NAND erase: device 0 offset 0x0, size 0x200000
Erasing at 0x0 – 6% complete.
Erasing at 0x20000 – 12% complete.
Erasing at 0x40000 – 18% complete.
Erasing at 0x60000 – 25% complete.
Erasing at 0x80000 – 31% complete.
Erasing at 0xa0000 – 37% complete.
Erasing at 0xc0000 – 43% complete.
Erasing at 0xe0000 – 50% complete.
Erasing at 0x100000 – 56% complete.
Erasing at 0x120000 – 62% complete.
Erasing at 0x140000 – 68% complete.
Erasing at 0x160000 – 75% complete.
Erasing at 0x180000 – 81% complete.
Erasing at 0x1a0000 – 87% complete.
Erasing at 0x1c0000 – 93% complete.