HCIA------VLAN配置实验

最新推荐文章于 2024-07-14 15:37:30 发布

谁把我睡的觉偷了xhxh

最新推荐文章于 2024-07-14 15:37:30 发布

阅读量1.4k

点赞数 43

文章标签：网络

本文链接：https://blog.csdn.net/printf_printf_/article/details/135940680

版权

文章详细描述了在三层网络环境中，如何配置二层VLAN（如VLAN2和VLAN3），包括在LSW3和LSW4交换机上定义端口类型和访问模式，以及AR5路由器上的子接口配置、IP地址池和DHCP服务。

摘要由CSDN通过智能技术生成

先对二层（数据链路层）进行配置

创建vlan2 和vlan3

对LSW3进行配置

[SW1]vlan 2
[SW1-vlan2]q
[SW1]vlan 3
[SW1-vlan3]q

[SW1]int g 0/0/3
[SW1-GigabitEthernet0/0/3]port link-type access
[SW1-GigabitEthernet0/0/3]port default vlan 2

[SW1-GigabitEthernet0/0/3]int g 0/0/4
[SW1-GigabitEthernet0/0/4]port link-type access
[SW1-GigabitEthernet0/0/4]port default vlan 3
[SW1-GigabitEthernet0/0/4]int g 0/0/2
[SW1-GigabitEthernet0/0/2]port link-type trunk
[SW1-GigabitEthernet0/0/2]port trunk allow-pass vlan all
[SW1-GigabitEthernet0/0/2]int g 0/0/1
[SW1-GigabitEthernet0/0/1]port link-type trunk
[SW1-GigabitEthernet0/0/1]port trunk allow-pass vlan all

对LSW4进行配置

[SW2-GigabitEthernet0/0/2]int g 0/0/1
[SW2-GigabitEthernet0/0/1]port link-type trunk
[SW2-GigabitEthernet0/0/1]port trunk allow-pass vlan all
[SW2-GigabitEthernet0/0/1]int g 0/0/2
[SW2-GigabitEthernet0/0/2]port link-type access
[SW2-GigabitEthernet0/0/2]port default vlan 2
[SW2-GigabitEthernet0/0/2]int g 0/0/3
[SW2-GigabitEthernet0/0/3]port link-type access
[SW2-GigabitEthernet0/0/3]port default vlan 3

AR5配置

[R1]int g 0/0/0.1
[R1-GigabitEthernet0/0/0.1]ip ad 192.168.1.1 24
[R1-GigabitEthernet0/0/0.1]dot1q termination vid 2
[R1-GigabitEthernet0/0/0.1]arp broadcast enable
[R1]int g 0/0/0.2
[R1-GigabitEthernet0/0/0.2]ip ad 192.168.2.1 24
[R1-GigabitEthernet0/0/0.2]dot1q termination vid 3
[R1-GigabitEthernet0/0/0.2]arp broadcast enable
[R1]dhcp enable
Info: The operation may take a few seconds. Please wait for a moment.done.
[R1]ip pool aa
Info: It's successful to create an IP address pool.
[R1-ip-pool-aa]network 192.168.1.0 mask 24
[R1-ip-pool-aa]gateway-list 192.168.1.1
[R1]ip pool aa
[R1-ip-pool-aa]q
[R1]int g 0/0/0.1
[R1-GigabitEthernet0/0/0.1]dhcp select global
[R1-GigabitEthernet0/0/0.1]q
[R1]ip pool bb
Info: It's successful to create an IP address pool.
[R1-ip-pool-bb]network 192.168.2.0 mask 24
[R1-ip-pool-bb]g
[R1-ip-pool-bb]gateway-list 192.168.2.1
[R1-ip-pool-bb]q
[R1]int g 0/0/0.2
[R1-GigabitEthernet0/0/0.2]dhcp se
[R1-GigabitEthernet0/0/0.2]dhcp select g
[R1-GigabitEthernet0/0/0.2]dhcp select global