CentOS6.5下 Asterisk 的安装、配置及 2个软电话实现互拨

从 asterisk 的安装到配置,到最后实现 2 个软电话(或者SIP话机亦可)之间互拨。花了大概2天时间,期间晕头转向砸桌子。。。。

当1002 收到来自1001 呼叫响铃的那瞬间,爽了O(∩_∩)O哈哈~


以下整理自网络:


一、安装asterisk相关软件包。

●安装dahdi驱动

[root@maple 2.6.32-71.el6.i686]# cd ~              #切换到root主目录下

[root@maple ~]# wget http://downloads.asterisk.org/pub/telephony/dahdi-linux/releases/dahdi-linux-2.5.0.tar.gz   #这里我用的dahdi-linux-2.5.0.tar.gz版本

[root@maple ~]# tar -xzf dahdi-linux-2.5.0.tar.gz 

[root@maple ~]# cd  dahdi-linux-2.5.0

[root@maple dahdi-linux-2.5.0]# make

[root@maple dahdi-linux-2.5.0]# make install

[root@maple dahdi-linux-2.5.0]# cd ..

 

[root@maple ~]# wget http://downloads.asterisk.org/pub/telephony/dahdi-tools/releases/dahdi-tools-2.5.0.tar.gz

[root@maple ~]# tar -xzf dahdi-tools-2.5.0.tar.gz 

[root@maple ~]# cd dahdi-tools-2.5.0

[root@maple dahdi-tools-2.5.0]# ./config

[root@maple dahdi-tools-2.5.0]# make

[root@maple dahdi-tools-2.5.0]# make install

[root@maple dahdi-tools-2.5.0]# make config

[root@maple dahdi-tools-2.5.0]# cd ..

 

[root@maple ~]# wget http://downloads.asterisk.org/pub/telephony/libpri/libpri-1.4.12.tar.gz

[root@maple ~]# tar -xzf libpri-1.4.12.tar.gz

[root@maple ~]# cd  libpri-1.4.12

[root@maple libpri-1.4.12]# make

[root@maple libpri-1.4.12]# make install

[root@maple libpri-1.4.12]#  cd ..

●安装asterisk

[root@maple ~]# wget http://downloads.asterisk.org/pub/telephony/asterisk/releases/asterisk-10.0.0-rc1.tar.gz

[root@maple ~]# tar -xzf asterisk-10.0.0-rc1.tar.gz

[root@maple ~]# cd asterisk-10.0.0-rc1

[root@maple asterisk-10.0.0-rc1]#  ./configure

[root@maple asterisk-10.0.0-rc1]#  make

[root@maple asterisk-10.0.0-rc1]#  make install

[root@maple asterisk-10.0.0-rc1]#  make samples

[root@maple asterisk-10.0.0-rc1]#  make config

[root@maple asterisk-10.0.0-rc1]#  cd ..

 

[root@maple ~]# wget http://downloads.asterisk.org/pub/telephony/asterisk/releases/asterisk-addons-1.6.2.4.tar.gz

[root@maple ~]# tar -xzf asterisk-addons-1.6.2.4.tar.gz

[root@maple ~]# cd asterisk-addons-1.6.2.4

[root@maple asterisk-addons-1.6.2.4]#  ./configure

[root@maple asterisk-addons-1.6.2.4]#  make cdr

[root@maple asterisk-addons-1.6.2.4]#  cp cdr/cdr_addon_mysql.so /usr/lib/asterisk/modules/

[root@maple asterisk-addons-1.6.2.4]#  cd ..



二、配置及SIP话机互拨部分


Step1:设置 sip.conf


root@Ubuntu:/etc/asterisk# vim sip.conf 

[general]                              //类似与全局变量
context  = default                
srvlookup = yes                   //DNS SRV记录查询
[111]
secret=aaa                         //密码,随意设置
port=5060                          //SIP端口地址
type=friend                         //类型为friend
host=dynamic                    //要求号码注册,以便Asterisk可以知道如何找到电话
qualify = yes                      //确认远端设备是否可达
nat = no                             //如果一个号码在NAT设备后面,例如防火墙,配置为yes
context = internal              //定义了指令的地点,用于控制电话的权限,及如何处理此号码的呼入呼叫。
canreinvite = no                //让Asterisk媒体通道经过自己,而不允许RTP信息直接在端点之间传送

;-----------华丽的分割线--------------
[222]
secret=aaa
port=5060
qualify = yes
nat = no
context = internal
canreinvite = no
type=friend
host=dynamic


Step2:设置extensions.conf


root@Ubuntu:/etc/asterisk# vim extensions.conf 

[internal]                                              //这里的internal和sip.conf里的context相同,可修改
exten => 1001,1,Dial(SIP/111)
exten => 1002,1,Dial(SIP/222)


Step3:打开Asterisk


root@Ubuntu:/home/blackhole# asterisk -crvvvvv

...

...

Ubuntu*CLI> 



Step4:设置X-lite

点击软件上方三角形ShowMenu

再点开SIP Account Settings,设置新账户

如图所示:


DisplayName可随意填写

User name 和Authorization user name填在sip.conf里面设置的名字我的是111就填111了

Domian就是本机的IP地址,proxy也是 但是记得加端口号

设置完点确定就OK了


此时 应该就能够看到

-- Registered SIP '111' at 172.19.60.10:45738
[Apr 15 20:33:15] NOTICE[1154]: chan_sip.c:24728 handle_request_subscribe: Received SIP subscribe for peer without mailbox: 111
Ubuntu*CLI> 


表示已经111已经连接上

此时你可以试试拨打1001

你会看到111在拨打自己

== Using SIP RTP CoS mark 5
    -- Executing [1001@internal:1] Dial("SIP/111-00000023", "SIP/111") in new stack
  == Using SIP RTP CoS mark 5
    -- Called SIP/111
    -- SIP/111-00000024 is ringing
    -- SIP/111-00000024 is ringing
  == Spawn extension (internal, 1001, 1) exited non-zero on 'SIP/111-00000023'
Ubuntu*CLI> 


Step5:设置eyeBeam


在此解释一下X-lite和eyeBeam其实是相同的,只是eyeBeam不能使用视频而X-lite可以

我只是用他们做个测试

所以设置和eyeBeam是相同的

设置好后

-- Registered SIP '222' at 172.19.60.10:15934
[Apr 15 20:42:55] NOTICE[1154]: chan_sip.c:24728 handle_request_subscribe: Received SIP subscribe for peer without mailbox: 222
Ubuntu*CLI> 

这样就可以呼叫X-lite啦 

拨打1001试试

当然也可以用X-lite拨打eyeBeam

 == Using SIP RTP CoS mark 5
    -- Executing [1001@internal:1] Dial("SIP/222-00000027", "SIP/111") in new stack
  == Using SIP RTP CoS mark 5
    -- Called SIP/111
    -- SIP/111-00000028 is ringing
    -- SIP/111-00000028 is ringing
Ubuntu*CLI> 

附图:


这样就算是成功了吧

注:如果extensions.conf被重新编写了 一定要记得在CLI那里reload一下

重新编写sip.conf就sip reload






参考:

http://blog.chinaunix.net/uid-23069658-id-3142076.html

http://blog.csdn.net/sukhoi27smk/article/details/17532249


  • 0
    点赞
  • 4
    收藏
    觉得还不错? 一键收藏
  • 0
    评论

“相关推荐”对你有帮助么?

  • 非常没帮助
  • 没帮助
  • 一般
  • 有帮助
  • 非常有帮助
提交
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值