VLAN实验

实验图

实验思路

1，在三台交换机上面分别创建vlan2、3、4、5、6。
2，在除pc1和pc3外其他电脑对应交换机的接口配置为hybrid接口，sw1连接路由器的接口也配置成hybrid接口，交换机之间配置成trunk口。
3，路由器配置两个IP地址池塘，一个用来给vlan2分配另一个用来给vlan3、4、5、6分配。
 

1，交换机配置

[SW1]vlan batch 2 to 6
[SW1]INT GigabitEthernet 0/0/1
[SW1-GigabitEthernet0/0/1]port link-type access 
[SW1-GigabitEthernet0/0/1]port default vlan 2
[SW1-GigabitEthernet0/0/1]int g 0/0/2
[SW1-GigabitEthernet0/0/2]port hybrid pvid vlan 3
[SW1-GigabitEthernet0/0/2]port hybrid untagged vlan 3 4 5 6
[SW1-GigabitEthernet0/0/2]int g 0/0/3
[SW1-GigabitEthernet0/0/3]port link-type trunk
[SW1-GigabitEthernet0/0/3]port trunk allow-pass vlan all
[SW1-GigabitEthernet0/0/4]port hybrid untagged vlan 3 4 5 6
[SW1-GigabitEthernet0/0/4]port hybrid tagged vlan 2
 

[SW2]vlan batch 2 to 6
[SW2-GigabitEthernet0/0/1]port link-type access 
[SW2-GigabitEthernet0/0/1]port default vlan 2
[SW2-GigabitEthernet0/0/1]int g 0/0/2
[SW2-GigabitEthernet0/0/2]port hybrid pvid vlan 4
[SW2-GigabitEthernet0/0/2]port hybrid untagged vlan 3 4 5
[SW2-GigabitEthernet0/0/2]int g 0/0/3
[SW2-GigabitEthernet0/0/3]port link-type trunk
[SW2-GigabitEthernet0/0/3]port trunk allow-pass vlan all
[SW2-GigabitEthernet0/0/3]int g 0/0/4
[SW2-GigabitEthernet0/0/4]port link-type trunk
[SW2-GigabitEthernet0/0/4]port trunk allow-pass vlan all
 

[SW3]vlan batch 2 to 6
[SW3]int g 0/0/1
[SW3-GigabitEthernet0/0/1]port hybrid pvid vlan 5
[SW3-GigabitEthernet0/0/1]port hybrid untagged vlan 3 4 5
[SW3-GigabitEthernet0/0/2]int g 0/0/2
[SW3-GigabitEthernet0/0/2]port hybrid untagged vlan 3 6
[SW3-GigabitEthernet0/0/1]int g 0/0/3
[SW3-GigabitEthernet0/0/3]port link-type trunk
[SW3-GigabitEthernet0/0/3]port trunk allow-pass vlan all
 

2，路由器配置

[r1]dhcp enable

[r1]ip pool a

[r1-ip-pool-a]network 192.168.1.0 mask 24

[r1-ip-pool-a]gateway-list 192.168.1.1

[r1]ip pool b

[r1-ip-pool-b]network 192.168.2.0 mask 24

[r1-ip-pool-b]gateway-list 192.168.2.1

[r1]int g0/0/0

[r1-GigabitEthernet0/0/0]ip address 192.168.1.1 24

[r1-GigabitEthernet0/0/0]dhcp select global

[r1-GigabitEthernet0/0/0]int g 0/0/0.1

[r1-GigabitEthernet0/0/0.1]dot1q termination vid 2

[r1-GigabitEthernet0/0/0.1]ip address 192.168.2.1 24

[r1-GigabitEthernet0/0/0.1]dhcp select global

3，检测

查看ip获取情况

然后检测

pc1,pc2是否可以访问pc3,4,5,6

pc4，pc5是否能访问pc6