ESP12E Shield+Arduino UNO R3开发板+DHT11温湿度模块+双色LED灯+有源蜂鸣器+光敏电阻模块+I2CLCD1602液晶显示器所构成的室内检测系统

室内检测系统由ESP12E Shield+Arduino UNO R3开发板+DHT11温湿度模块+双色LED灯+有源蜂鸣器+光敏电阻模块+I2CLCD1602液晶显示器所构成。DHT11温湿度模块获取室内温湿度数据通过I2CLCD1602液晶显示器进行显示，另一方面通过ESP12E Shield将数据上传至云平台。光敏电阻进行捕获室内光照强度，若光照强度过弱，即日光过弱，周围环境太黑暗低于设定的阈值，则有源蜂鸣器警报，双色LED灯变红，正常情况下LED灯为绿色。

一、设备准备

Arduino UNO R3

I2CLCD1602液晶显示器

ESP12E Shield

DHT11温湿度模块

有源蜂鸣器

光敏电阻模块

双色LED灯

二、设备连接

ESP12E Shield直接覆盖Arduino UNO R3开发板

DHT11模块

DHT11模块	Arduino UNO R3
+	5V
-	GND
OUT	P2

I2CLCD1602液晶显示器

I2CLCD1602液晶显示器	Arduino UNO R3
GDN	GND
VCC	5V
SDA	A4
SCL	A5

光敏电阻模块

光敏电阻模块	Arduino UNO R3
VCC	5V
GND	GND
AO	A0

有源蜂鸣器

有源蜂鸣器	Arduino UNO R3
GND	GND
I/O	P7
VCC	5V

双色LED灯

双色LED灯	Arduino UNO R3
GND	GND
R	P11
G	P10

三、云平台设置

联网上传至服务器的配置可参考该篇博文
一、Arduino UNO R3将数据上传至云平台
需要添加俩个设备名称分别为humi和temp用于存放温湿度信息

四、完整代码

#include <dht.h>
#include <LiquidCrystal_I2C.h>
#include <Wire.h> 
LiquidCrystal_I2C lcd(0x27,16,2);  // set the LCD address to 0x27 and 0x3F for a 16 chars and 2 line display

dht DHT;//create a variable type of dht

const int DHT11_PIN= 2;//Humiture sensor attach to pin2

const int greenPin = 11;  // R petal on RGB LED module connected to digital pin 11 
const int redPin= 10;  // G petal on RGB LED module connected to digital pin 10 

const int photocellPin = A0; //photoresistor module attach to A0
int outputValue = 0;
const int buzzerPin=7;  //buzzer attach to digital 7
int val = 0; 
int wendu=0;
int shidu=0;
void setup()
{
  Serial.begin(9600);
  randomSeed(analogRead(0));
  pinMode(buzzerPin,OUTPUT);
  pinMode(redPin, OUTPUT); //set redPin as OUTPUT
  pinMode(greenPin, OUTPUT);//set greenPin as OUTPUT
  lcd.init();  //initialize the lcd
  lcd.backlight();  //open the backlight 
}

void loop()
{
  // READ DATA
  //Serial.println("DHT11:");
  
D: int chk = DHT.read11(DHT11_PIN);//read the value returned from sensor
  switch (chk)
  {
  case DHTLIB_OK:  
    //Serial.println("OK!"); 
    break;
  case DHTLIB_ERROR_CHECKSUM: 
    //goto D;
    //Serial.print("Checksum error,\t"); 
    break;
  case DHTLIB_ERROR_TIMEOUT: 
    //goto D;
    //Serial.print("Time out error,\t"); 
    break;
  default: 
    // goto D;
    //Serial.print("Unknown error,\t"); 
    break;
  }
  // DISPLAY DATA
  lcd.setCursor(0, 0);
  lcd.print("Tem:");
  //Serial.print("Tem:");
  lcd.print(DHT.temperature,1); //print the temperature on lcd 
  
  wendu = DHT.temperature;
/*
  Serial.print("wendu:");
  Serial.print(wendu);
  Serial.print("\n");
*/
  Serial.print("cmd=upload&device_name=temp&data=");
  Serial.print(wendu);//send a random number
  Serial.println("&uid=beyondyy&key=6d2cc6e3e19efa259a302fcf4166e2ce");


  
  lcd.print(char(223));//print the unit" ℃ "
  lcd.print("C");
  // Serial.println(" C");
  lcd.setCursor(0, 1);
  lcd.print("Hum:");
  //Serial.print("Hum:");
  lcd.print(DHT.humidity,1); //print the humidity on lcd

  shidu = DHT.humidity;
  /*
  Serial.print("shidu:");
  Serial.print(shidu);
  Serial.print("\n");
  */
  Serial.print("cmd=upload&device_name=humi&data=");
  Serial.print(shidu);//send a random number
  Serial.println("&uid=beyondyy&key=6d2cc6e3e19efa259a302fcf4166e2ce");

  lcd.print(" %"); 
  //Serial.println(" %");
  delay(200); //wait a while 

  outputValue = analogRead(photocellPin);//read the value of photoresistor
  //Serial.println(outputValue); //print it in serial monitor
  
  if(outputValue >= 500) //else
  {
    
    digitalWrite(buzzerPin,LOW);
    analogWrite(redPin, 255); //red value decrease
    analogWrite(greenPin, 0); //green value decrease
    delay(100);
    //Serial.println(val, DEC);

  }
  else
  {
    digitalWrite(buzzerPin,HIGH);
    analogWrite(greenPin, 255); //green value decrease
    analogWrite(redPin, 0); //red value decrease
    delay(100);
  }
  delay(1000); //delay 1s

}

所需库下载连接
将下载好的压缩包解压，把文件Dht复制到你的编译器Arduino的libraries文件夹下

五、视频效果演示

基于Arduino UNO R3开发板的安全检测系统的实现---DHT11数据采集上云

视频链接CSDN
视频链接B站