MGRE环境下OSPF配置

文章目录

• • 拓扑图
  • 实验要求
  • 具体操作过程
  • 实验结果
     

拓扑图

实验要求

要求：

1、R6为ISP，只配置IP地址，R1-R5的环回为私有网段

2、R1/R4/R5为全连的MGRE结构，R1/R2/R3为星型的拓扑结构，R1为中心站点

3、所有私有网段可以互相通讯，私有网段使用OSPF完成

具体操作过程

1、给所有设备配置IP
r1配置：

[r1]int g 0/0/0
[r1-GigabitEthernet0/0/0]ip address 1.1.0.1 30
[r1-GigabitEthernet0/0/0]int GigabitEthernet 0/0/1
[r1-GigabitEthernet0/0/1]ip address 1.2.0.1 30
[r1-GigabitEthernet0/0/1]int lo0
[r1-LoopBack0]ip address 192.168.1.1 24

r2配置：

[r2]int g 0/0/0 
[r2-GigabitEthernet0/0/0]ip address 2.0.0.1 30
[r2-GigabitEthernet0/0/0]int lo0
[r2-LoopBack0]ip address 192.168.2.1 24

r3配置：

[r3]int g0/0/0  
[r3-GigabitEthernet0/0/0]ip address 3.0.0.1 30
[r3-GigabitEthernet0/0/0]int lo0
[r3-LoopBack0]ip address 192.168.3.1 24

r4配置：

[r4]int g0/0/0
[r4-GigabitEthernet0/0/0]ip address 4.0.0.1 30
[r4-GigabitEthernet0/0/0]int lo0
[r4-LoopBack0]ip address 192.168.4.1 24

r5配置：

[r5]int g0/0/0  
[r5-GigabitEthernet0/0/0]ip address 5.0.0.1 30
[r5-GigabitEthernet0/0/0]int lo0
[r5-LoopBack0]ip address 192.168.5.1 24

r6配置：

[r6]int g 0/0/1 
[r6-GigabitEthernet0/0/1]ip address 1.2.0.2 30
[r6-GigabitEthernet0/0/1]int g 0/0/0
[r6-GigabitEthernet0/0/0]ip address 1.1.0.2 30
[r6-GigabitEthernet0/0/0]int g 4/0/1
[r6-GigabitEthernet4/0/1]ip address 2.0.0.2 30
[r6-GigabitEthernet4/0/1]int g 0/0/2
[r6-GigabitEthernet0/0/2]ip address 3.0.0.2 30
[r6-GigabitEthernet0/0/2]int g 4/0/0
[r6-GigabitEthernet4/0/0]ip address 4.0.0.2 30
[r6-GigabitEthernet4/0/0]int g 4/0/2
[r6-GigabitEthernet4/0/2]ip address 5.0.0.2 30

2、配置缺省
[r1]ip route-static 0.0.0.0 0 1.2.0.2 

[r1]ip route-static 0.0.0.0 0 1.1.0.2

[r2]ip route-static 0.0.0.0 0 2.0.0.2

[r3]ip route-static 0.0.0.0 0 3.0.0.2

[r4]ip route-static 0.0.0.0 0 4.0.0.2

[r5]ip route-static 0.0.0.0 0 5.0.0.2

3.给R1/R4/R5配置全连MGRE
r1配置：

[r1]interface Tunnel 0/0/1
[r1-Tunnel0/0/1]ip address 192.168.7.1 24
[r1-Tunnel0/0/1]tunnel-protocol gre p2mp
[r1-Tunnel0/0/1]source 1.2.0.1
[r1-Tunnel0/0/1]nhrp network-id 101
[r1-Tunnel0/0/1]nhrp entry 192.168.7.2 4.0.0.1 register
[r1-Tunnel0/0/1]nhrp entry 192.168.7.3 5.0.0.1 register

r4配置：

[r4]interface Tunnel 0/0/1
[r4-Tunnel0/0/1]ip address 192.168.7.2 24
[r4-Tunnel0/0/1]tunnel-protocol gre p2mp
[r4-Tunnel0/0/1]source 4.0.0.1
[r4-Tunnel0/0/1]nhrp network-id 101 
[r4-Tunnel0/0/1]nhrp entry 192.168.7.1 1.2.0.1 register 
[r4-Tunnel0/0/1]nhrp entry 192.168.7.3 5.0.0.1 register

r5配置：

[r5]interface Tunnel 0/0/1
[r5-Tunnel0/0/1]ip address 192.168.7.3 24
[r5-Tunnel0/0/1]tunnel-protocol gre p2mp 
[r5-Tunnel0/0/1]nhrp network-id 101
[r5-Tunnel0/0/1]source 5.0.0.1
[r5-Tunnel0/0/1]nhrp entry 192.168.7.1 1.2.0.1 register   
[r5-Tunnel0/0/1]nhrp entry 192.168.7.2 4.0.0.1 register

4、R1/R2/R3配置星型拓扑
r1配置：

[r1]interface Tunnel 0/0/0
[r1-Tunnel0/0/0]ip address 192.168.6.1 24
[r1-Tunnel0/0/0]tunnel-protocol gre p2mp
[r1-Tunnel0/0/0]nhrp network-id 100
[r1-Tunnel0/0/0]nhrp entry multicast dynamic 
[r1-Tunnel0/0/0]source 1.1.0.1
[r1-Tunnel0/0/0]ospf network-type broadcast 

r2配置：

[r2]interface Tunnel 0/0/0
[r2-Tunnel0/0/0]ip address 192.168.6.2 24
[r2-Tunnel0/0/0]tunnel-protocol gre p2mp
[r2-Tunnel0/0/0]source g0/0/0
[r2-Tunnel0/0/0]nhrp network-id 100
[r2-Tunnel0/0/0]nhrp entry 192.168.6.1 1.1.0.1 register

r3配置：

[r3]interface Tunnel 0/0/0
[r3-Tunnel0/0/0]ip address 192.168.6.3 24
[r3-Tunnel0/0/0]tunnel-protocol gre p2mp
[r3-Tunnel0/0/0]source g0/0/0
[r3-Tunnel0/0/0]nhrp network-id 100
[r3-Tunnel0/0/0]nhrp entry 192.168.6.1 1.1.0.1 register

5、ospf
r1配置：

[r1]ospf router-id 1.1.1.1 
[r1-ospf-1]area 0
[r1-ospf-1-area-0.0.0.0]network 192.168.1.0  0.0.0.0
[r1-ospf-1-area-0.0.0.0]network 192.168.6.0  0.0.0.255
[r1-ospf-1-area-0.0.0.0]network 192.168.7.0  0.0.0.255

r2配置：

[r2]ospf router-id 2.2.2.2
[r2-ospf-1]area 0
[r2-ospf-1-area-0.0.0.0]network 192.168.2.0 0.0.0.255
[r2-ospf-1-area-0.0.0.0]network 192.168.6.0 0.0.0.255

r3配置：

[r3]ospf router-id 3.3.3.3
[r3-ospf-1]area 0
[r3-ospf-1-area-0.0.0.0]network 192.168.3.0 0.0.0.255
[r3-ospf-1-area-0.0.0.0]network 192.168.6.0 0.0.0.255

r4配置：

[r4]ospf router-id 4.4.4.4
[r4-ospf-1]area 0 
[r4-ospf-1-area-0.0.0.0]network 192.168.4.0 0.0.0.255
[r4-ospf-1-area-0.0.0.0]network 192.168.7.0 0.0.0.255

r5配置：

[r5]ospf router-id 5.5.5.5
[r5-ospf-1]area 0  
[r5-ospf-1-area-0.0.0.0]network 192.168.5.0 0.0.0.255
[r5-ospf-1-area-0.0.0.0]network 192.168.7.0 0.0.0.255
 

实验结果