STC15f2k60s2C语言定时器2,请问STC15F2K60S2的定时时间怎么求啊 ？？？？

该楼层疑似违规已被系统折叠 隐藏此楼查看此楼

void Timer_config(void)

{

TIM_InitTypeDef TIM_InitStructure; //结构定义

TIM_InitStructure.TIM_Mode = TIM_16BitAutoReload; //指定工作模式, TIM_16BitAutoReload,TIM_16Bit,TIM_8BitAutoReload,TIM_16BitAutoReloadNoMask

TIM_InitStructure.TIM_Polity = PolityLow; //指定中断优先级, PolityHigh,PolityLow

TIM_InitStructure.TIM_Interrupt = DISABLE; //中断是否允许, ENABLE或DISABLE

TIM_InitStructure.TIM_ClkSource = TIM_CLOCK_1T; //指定时钟源, TIM_CLOCK_1T,TIM_CLOCK_12T,TIM_CLOCK_Ext

TIM_InitStructure.TIM_ClkOut = ENABLE; //是否输出高速脉冲, ENABLE或DISABLE

TIM_InitStructure.TIM_Value = 65536UL - (MAIN_Fosc / 100000UL); //初值,

TIM_InitStructure.TIM_Run = ENABLE; //是否初始化后启动定时器, ENABLE或DISABLE

Timer_Inilize(Timer0,&TIM_InitStructure); //初始化Timer0 Timer0,Timer1,Timer2

TIM_InitStructure.TIM_Mode = TIM_16BitAutoReload; //指定工作模式, TIM_16BitAutoReload,TIM_16Bit,TIM_8BitAutoReload,TIM_16BitAutoReloadNoMask

TIM_InitStructure.TIM_Polity = PolityLow; //指定中断优先级, PolityHigh,PolityLow

TIM_InitStructure.TIM_Interrupt = ENABLE; //中断是否允许, ENABLE或DISABLE

TIM_InitStructure.TIM_ClkSource = TIM_CLOCK_1T; //指定时钟源, TIM_CLOCK_1T,TIM_CLOCK_12T,TIM_CLOCK_Ext

TIM_InitStructure.TIM_ClkOut = ENABLE; //是否输出高速脉冲, ENABLE或DISABLE

TIM_InitStructure.TIM_Value = 65536UL - (MAIN_Fosc / 1000); //初值,

TIM_InitStructure.TIM_Run = ENABLE; //是否初始化后启动定时器, ENABLE或DISABLE

Timer_Inilize(Timer1,&TIM_InitStructure); //初始化Timer1 Timer0,Timer1,Timer2

TIM_InitStructure.TIM_Interrupt = ENABLE; //中断是否允许, ENABLE或DISABLE. (注意: Timer2固定为16位自动重装, 中断固定为低优先级)

TIM_InitStructure.TIM_ClkSource = TIM_CLOCK_12T; //指定时钟源, TIM_CLOCK_1T,TIM_CLOCK_12T,TIM_CLOCK_Ext

TIM_InitStructure.TIM_ClkOut = ENABLE; //是否输出高速脉冲, ENABLE或DISABLE

TIM_InitStructure.TIM_Value = 65536UL - (MAIN_Fosc / (50*12)); //初值

TIM_InitStructure.TIM_Run = ENABLE; //是否初始化后启动定时器, ENABLE或DISABLE

Timer_Inilize(Timer2,&TIM_InitStructure); //初始化Timer2 Timer0,Timer1,Timer2

}