keepalived+lvs+usp安装实施文档

最新推荐文章于 2024-05-18 16:23:13 发布

weixin_30633405

最新推荐文章于 2024-05-18 16:23:13 发布

阅读量54

点赞数

文章标签：网络操作系统

原文链接：http://www.cnblogs.com/pigdragon/p/6432483.html

版权

操作系统平台：RedHat6.4 x86_64

软件：LVS+keepalived LVS+Keepalived

介绍 LVS LVS是Linux Virtual Server的简写，意即Linux虚拟服务器，是一个虚拟的服务器集群系统。本项目在1998年5月由章文嵩博士成立，是中国国内最早出现的自由软件项目之一。目前有三种IP负载均衡技术（VS/NAT、VS/TUN和VS/DR）；十种调度算法（rrr|wrr|lc|wlc|lblc|lblcr|dh|sh|sed|nq）。 Keepalvied Keepalived在这里主要用作RealServer的健康状态检查以及LoadBalance主机和BackUP主机之间failover的实现

IP配置信息:

LVS-DR-Master 192.168.20.135

LVS-DR-BACKUP 192.168.20.136

LVS-DR-VIP 192.168.20.160

WEB1-Realserver 192.168.20.121

WEB2-Realserver 192.168.20.123

GateWay 192.168.20.253

安装LVS和Keepalvied软件包

1. 下载相关软件包 #mkdir /usr/local/src/lvs #cd /usr/local/src/lvs #wget http://www.linuxvirtualserver.org/software/kernel-2.6/ipvsadm-1.24.tar.gz #wget http://www.keepalived.org/software/keepalived-1.1.15.tar.gz

2. 安装LVS和Keepalived

#lsmod |grep ip_vs

#uname -r

#ln -s /usr/src/kernels/2.6.32-358.el6.x86_64/ /usr/src/linux

#tar zxvf ipvsadm-1.24.tar.gz

#cd ipvsadm-1.24

#make && make install

#find / -name ipvsadm # 查看ipvsadm的位置

#tar zxvf keepalived-1.1.15.tar.gz

#cd keepalived-1.1.15

#./configure && make && make install

#find / -name keepalived # 查看keepalived位置

#cp /usr/local/etc/rc.d/init.d/keepalived /etc/rc.d/init.d/

#cp /usr/local/etc/sysconfig/keepalived /etc/sysconfig/

#mkdir /etc/keepalived

#cp /usr/local/etc/keepalived/keepalived.conf /etc/keepalived/

#cp /usr/local/sbin/keepalived /usr/sbin/

#service keepalived start|stop #做成系统启动服务方便管理.

四. 配置LVS实现负载均衡

1． LVS-DR，配置LVS脚本实现负载均衡

vi /usr/local/sbin/lvs-dr.sh #!/bin/bash

# description: start LVS of DirectorServer

#Written by :NetSeek

#http://www.linuxtone.org

GW=192.168.20.253

# website director vip.

WEB_VIP=192.168.20.160

WEB_RIP1=192.168.20.155

WEB_RIP2=192.168.20.156

. /etc/rc.d/init.d/functions

logger $0 called with $1

case "$1" in

start)

# Clear all iptables rules.

/sbin/iptables -F

# Reset iptables counters.

/sbin/iptables -Z

# Clear all ipvsadm rules/services.

/sbin/ipvsadm -C

#set lvs vip for dr

/sbin/ipvsadm --set 30 5 60

/sbin/ifconfig eth0:0 $WEB_VIP broadcast $WEB_VIP netmask 255.255.255.255 up

/sbin/route add -host $WEB_VIP dev eth0:0

/sbin/ipvsadm -A -t $WEB_VIP:22 -s wrr -p 3

/sbin/ipvsadm -a -t $WEB_VIP:22 -r $WEB_RIP1:22 -g -w 1

/sbin/ipvsadm -a -t $WEB_VIP:22 -r $WEB_RIP2:22 -g -w 1

/sbin/ipvsadm -A -t $WEB_VIP:3389 -s wrr -p 3

/sbin/ipvsadm -a -t $WEB_VIP:3389 -r $WEB_RIP1:3389 -g -w 1

/sbin/ipvsadm -a -t $WEB_VIP:3389 -r $WEB_RIP2:3389 -g -w 1

/sbin/ipvsadm -A -t $WEB_VIP:33389 -s wrr -p 3

/sbin/ipvsadm -a -t $WEB_VIP:33389 -r $WEB_RIP1:33389 -g -w 1

/sbin/ipvsadm -a -t $WEB_VIP:33389 -r $WEB_RIP2:33389 -g -w 1

/sbin/ipvsadm -A -t $WEB_VIP:62000 -s wrr -p 3

/sbin/ipvsadm -a -t $WEB_VIP:62000 -r $WEB_RIP1:62000 -g -w 1

/sbin/ipvsadm -a -t $WEB_VIP:62000 -r $WEB_RIP2:62000 -g -w 1

/sbin/ipvsadm -A -t $WEB_VIP:21 -s wrr -p 3

/sbin/ipvsadm -a -t $WEB_VIP:21 -r $WEB_RIP1:21 -g -w 1

/sbin/ipvsadm -a -t $WEB_VIP:21 -r $WEB_RIP2:21 -g -w 1

/sbin/ipvsadm -A -t $WEB_VIP:55555 -s wrr -p 3

/sbin/ipvsadm -a -t $WEB_VIP:55555 -r $WEB_RIP1:55555 -g -w 1

/sbin/ipvsadm -a -t $WEB_VIP:55555 -r $WEB_RIP2:55555 -g -w 1

/sbin/ipvsadm -A -t $WEB_VIP:8080 -s wrr -p 3

/sbin/ipvsadm -a -t $WEB_VIP:8080 -r $WEB_RIP1:8080 -g -w 1

/sbin/ipvsadm -a -t $WEB_VIP:8080 -r $WEB_RIP2:8080 -g -w 1

/sbin/ipvsadm -A -t $WEB_VIP:8081 -s wrr -p 3

/sbin/ipvsadm -a -t $WEB_VIP:8081 -r $WEB_RIP1:8081 -g -w 1

/sbin/ipvsadm -a -t $WEB_VIP:8081 -r $WEB_RIP2:8081 -g -w 1

touch /var/lock/subsys/ipvsadm >/dev/null 2>&1

# set Arp

/sbin/arping -I eth0 -c 5 -s $WEB_VIP $GW >/dev/null 2>&1

;;

stop)

/sbin/ipvsadm -C

/sbin/ipvsadm -Z

ifconfig eth0:0 down

route del $WEB_VIP >/dev/null 2>&1

rm -rf /var/lock/subsys/ipvsadm >/dev/null 2>&1

/sbin/arping -I eth0 -c 5 -s $WEB_VIP $GW

echo "ipvsadm stoped"

;;

status)

if [ ! -e /var/lock/subsys/ipvsadm ];then

echo "ipvsadm is stoped"

exit 1

else

ipvsadm -ln

echo "..........ipvsadm is OK."

;;

echo "Usage: $0 {start|stop|status}"

exit 1

esac

exit 0

2．配置Realserver脚本.

在web1和web2上配置realserver脚本：

cat /etc/rc.d/init.d/realserver.sh

#!/bin/bash

# Written by NetSeek

# description: Config realserver lo and apply noarp

WEB_VIP=192.168.20.160

. /etc/rc.d/init.d/functions

case "$1" in

start)

ifconfig lo:0 $WEB_VIP netmask 255.255.255.255 broadcast $WEB_VIP

/sbin/route add -host $WEB_VIP dev lo:0

echo "1" >/proc/sys/net/ipv4/conf/lo/arp_ignore

echo "2" >/proc/sys/net/ipv4/conf/lo/arp_announce

echo "1" >/proc/sys/net/ipv4/conf/all/arp_ignore

echo "2" >/proc/sys/net/ipv4/conf/all/arp_announce

sysctl -p >/dev/null 2>&1

echo "RealServer Start OK"

;;

stop)

ifconfig lo:0 down

route del $WEB_VIP >/dev/null 2>&1

echo "0" >/proc/sys/net/ipv4/conf/lo/arp_ignore

echo "0" >/proc/sys/net/ipv4/conf/lo/arp_announce

echo "0" >/proc/sys/net/ipv4/conf/all/arp_ignore

echo "0" >/proc/sys/net/ipv4/conf/all/arp_announce

echo "RealServer Stoped"

;;

status)

# Status of LVS-DR real server.

islothere=`/sbin/ifconfig lo:0 | grep $WEB_VIP`

isrothere=`netstat -rn | grep "lo:0" | grep $web_VIP`

if [ ! "$islothere" -o ! "isrothere" ];then

# Either the route or the lo:0 device

# not found.

echo "LVS-DR real server Stopped."

else

echo "LVS-DR Running."

;;

# Invalid entry.

echo "$0: Usage: $0 {start|status|stop}"

exit 1

;;

esac

exit 0

附上realserver机上的/etc/sysctl.conf ：

# Kernel sysctl configuration file for Red Hat Linux

# # For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and # sysctl.conf(5) for more details.

# Controls IP packet forwarding

net.ipv4.ip_forward = 1

# Controls source route verification

net.ipv4.conf.default.rp_filter = 1

# Do not accept source routing

net.ipv4.conf.default.accept_source_route = 0

# Controls the System Request debugging functionality of the kernel

kernel.sysrq = 0

# Controls whether core dumps will append the PID to the core filename.

# Useful for debugging multi-threaded applications.

kernel.core_uses_pid = 1

net.ipv4.conf.lo.arp_ignore = 1

net.ipv4.conf.lo.arp_announce = 2

net.ipv4.conf.all.arp_ignore = 1

net.ipv4.conf.all.arp_announce = 2

或者采用secondary ip address方式配置

# vi /etc/sysctl.conf

添加以下内容如上所示：

net.ipv4.conf.lo.arp_ignore = 1

net.ipv4.conf.lo.arp_announce = 2

net.ipv4.conf.all.arp_ignore = 1

net.ipv4.conf.all.arp_announce = 2

#sysctl –p

#ip addr list 查看是否绑定

3. 启动lvs-dr脚本和realserver脚本，在DR上可以查看LVS当前状态:

#watch ipvsadm –ln

五．利用Keepalvied实现负载均衡和和高可用性

1.配置在主负载均衡服务器上配置keepalived.conf

#vi /etc/keepalived/keepalived.conf (主调度器) ! Configuration File for keepalived

global_defs {

notification_email {

acassen@firewall.loc

failover@firewall.loc

sysadmin@firewall.loc

}

notification_email_from Alexandre.Cassen@firewall.loc

smtp_server 192.168.200.1

smtp_connect_timeout 30

router_id LVS_DEVEL

}

vrrp_instance VI_1 {

state MASTER # 状态实际MASTER

interface eth0 # 监听网卡切换

virtual_router_id 51

priority 100 # 优先级（越大优先级越高）

advert_int 1

authentication {

auth_type PASS

auth_pass 1111

}

virtual_ipaddress { # 虚拟IP地址列表，即VIP

192.168.20.160

}

virtual_server 192.168.20.160 9080 {

delay_loop 6

lb_algo wrr #分发算法

lb_kind DR # DR模式

nat_mask 255.255.255.0

persistence_timeout 50

protocol TCP

real_server 192.168.20.121 9080 {

weight 3 # 权重（权重越高处理的请求越多）

TCP_CHECK {

connect_port 9080

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

real_server 192.168.20.123 9080 {

weight 3

TCP_CHECK {

connect_port 9080

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

virtual_server 192.168.20.160 9081 {

delay_loop 6

lb_algo wrr

lb_kind DR

nat_mask 255.255.255.0

persistence_timeout 50

protocol TCP

real_server 192.168.20.121 9081 {

weight 3

TCP_CHECK {

connect_port 9081

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

real_server 192.168.20.123 9081 {

weight 3

TCP_CHECK {

connect_port 9081

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

virtual_server 192.168.20.160 22 {

delay_loop 6

lb_algo wrr

lb_kind DR

nat_mask 255.255.255.0

persistence_timeout 50

protocol TCP

real_server 192.168.20.121 22 {

weight 3

TCP_CHECK {

connect_port 22

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

real_server 192.168.20.123 22 {

weight 3

TCP_CHECK {

connect_port 22

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

virtual_server 192.168.20.160 3389 {

delay_loop 6

lb_algo wrr

lb_kind DR

nat_mask 255.255.255.0

persistence_timeout 50

protocol TCP

real_server 192.168.20.121 3389 {

weight 3

TCP_CHECK {

connect_port 3389

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

real_server 192.168.20.123 3389 {

weight 3

TCP_CHECK {

connect_port 3389

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

virtual_server 192.168.20.160 33389 {

delay_loop 6

lb_algo wrr

lb_kind DR

nat_mask 255.255.255.0

persistence_timeout 50

protocol TCP

real_server 192.168.20.121 33389 {

weight 3

TCP_CHECK {

connect_port 33389

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

real_server 192.168.20.123 33389 {

weight 3

TCP_CHECK {

connect_port 33389

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

virtual_server 192.168.20.160 55555 {

delay_loop 6

lb_algo wrr

lb_kind DR

nat_mask 255.255.255.0

persistence_timeout 50

protocol TCP

real_server 192.168.20.121 55555 {

weight 3

TCP_CHECK {

connect_port 55555

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

real_server 192.168.20.123 55555 {

weight 3

TCP_CHECK {

connect_port 55555

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

virtual_server 192.168.20.160 62000 {

delay_loop 6

lb_algo wrr

lb_kind DR

nat_mask 255.255.255.0

persistence_timeout 50

protocol TCP

real_server 192.168.20.121 62000 {

weight 3

TCP_CHECK {

connect_port 62000

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

real_server 192.168.20.123 62000 {

weight 3

TCP_CHECK {

connect_port 62000

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

virtual_server 192.168.20.160 21 {

delay_loop 6

lb_algo wrr

lb_kind DR

nat_mask 255.255.255.0

persistence_timeout 50

protocol TCP

real_server 192.168.20.121 21 {

weight 3

TCP_CHECK {

connect_port 21

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

real_server 192.168.20.123 21 {

weight 3

TCP_CHECK {

connect_port 21

connect_timeout 3

nb_get_retry 3

delay_before_retry 3

}

2. BACKUP服务器同上配置，先安装lvs再按装keepalived,仍后配置/etc/keepalived/keepalived.conf，只需将红色标示的部分改一下即可（state MASTER 改成 state BACKUP priority 100改成 priority 99 ）.

3. #/etc/init.d/keepalived start 启动keepalived 服务，keepalived就能利用keepalived.conf 配置文件，实现负载均衡和高可用.

4. 查看lvs服务是否正常

Ipvsadm -l -> RemoteAddress:Port Forward Weight ActiveConn InActConn

TCP 192.168.20.160:33389 wrr persistent 50

-> 192.168.20.121:33389 Route 3 0 0

-> 192.168.20.123:33389 Route 3 0 0

TCP 192.168.20.160:62000 wrr persistent 50

-> 192.168.20.121:62000 Route 3 0 0

-> 192.168.20.123:62000 Route 3 0 0

TCP 192.168.20.160:55555 wrr persistent 50

-> 192.168.20.121:55555 Route 3 0 0

-> 192.168.20.123:55555 Route 3 0 0

TCP 192.168.20.160:3389 wrr persistent 50

-> 192.168.20.121:3389 Route 3 0 0

-> 192.168.20.123:3389 Route 3 0 0

TCP 192.168.20.160:22 wrr persistent 50

-> 192.168.20.121:22 Route 3 0 0

-> 192.168.20.123:22 Route 3 0 0

TCP 192.168.20.160:21 wrr persistent 50

TCP 192.168.20.160:9081 wrr persistent 50

-> 192.168.20.121:9081 Route 3 0 0

-> 192.168.20.123:9081 Route 3 0 0

TCP 192.168.20.160:9080 wrr persistent 50

-> 192.168.20.121:9080 Route 3 0 0

-> 192.168.20.123:9080 Route 3 0 0

#watch ipvsadm –ln

IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddressort Scheduler Flags -> RemoteAddressort

Forward Weight ActiveConn InActConn

#tail –f /var/log/message 监听日志，查看状态，测试LVS负载均衡及高可用性是否有效。

5．停Master服务器的keepalived服务，查看BAKCUP服务器是否能正常接管服务。

转载于:https://www.cnblogs.com/pigdragon/p/6432483.html

weixin_30633405

关注

0
点赞
踩
0

收藏

觉得还不错? 一键收藏
0
评论
keepalived+lvs+usp安装实施文档

操作系统平台：RedHat6.4x86_64软件：LVS+keepalived LVS+Keepalived 介绍 LVS LVS是Linux Virtual Server的简写，意即Linux虚拟服务器，是一个虚拟的服务器集群系统。本项目在1998年5月由章文嵩博士成立，是中国国内最早出现的自由软件项目之一。目前有三种IP负载均衡技术（VS/NAT、VS/TUN和VS/DR）；十种...
复制链接

扫一扫