eNSP的使用

1- 进入华为路由器界面配置ip
The device is running!
####################################
Nov  1 2016 23:39:24-08:00 Huawei %%01IFNET/4/BOARD_ENABLE(l)[0]:Board 1 has bee
n available.
<Huawei>
Nov  1 2016 23:39:24-08:00 Huawei %%01IFNET/4/IF_ENABLE(l)[1]:Interface Serial1/
0/0 has been available.
<Huawei>
Nov  1 2016 23:39:24-08:00 Huawei %%01IFNET/4/IF_ENABLE(l)[2]:Interface Serial1/
0/1 has been available.
<Huawei>
Nov  1 2016 23:39:25-08:00 Huawei %%01IFPDT/4/IF_STATE(l)[3]:Interface GigabitEt
hernet0/0/0 has turned into UP state.
<Huawei>
Nov  1 2016 23:39:28-08:00 Huawei %%01IFPDT/4/IF_STATE(l)[4]:Interface Serial1/0
/0 has turned into UP state.
<Huawei>
Nov  1 2016 23:39:30-08:00 Huawei %%01IFNET/4/LINK_STATE(l)[5]:The line protocol
 PPP on the interface Serial1/0/0 has entered the UP state.
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys Shenzhen
[Shenzhen]
[Shenzhen]int g0/0/0
[Shenzhen-GigabitEthernet0/0/0]ip add 10.1.1.254 24
[Shenzhen-GigabitEthernet0/0/0]
Nov  1 2016 23:42:50-08:00 Shenzhen %%01IFNET/4/LINK_STATE(l)[6]:The line protoc
ol IP on the interface GigabitEthernet0/0/0 has entered the UP state.
[Shenzhen-GigabitEthernet0/0/0]
[Shenzhen-GigabitEthernet0/0/0]

2- 保存配置文件
[R2-GigabitEthernet0/0/0]  ##############ctrl+z 退出
<R2>save
  The current configuration will be written to the device.
  Are you sure to continue? (y/n)[n]:y
  It will take several minutes to save configuration file, please wait........
  Configuration file had been saved successfully
  Note: The configuration file will take effect after being activated
 
 
3- 查看配置命令
进入全局模式
system-view #### sys
dis cu

<R1>system-view
Enter system view, return user view with Ctrl+Z.
[R1]dis cu
[V200R003C00]
#
 sysname R1
#
 snmp-agent local-engineid 800007DB03000000000000
 snmp-agent
#
 clock timezone China-Standard-Time minus 08:00:00
#
portal local-server load flash:/portalpage.zip
#
 drop illegal-mac alarm
#
 wlan ac-global carrier id other ac id 0
#
 set cpu-usage threshold 80 restore 75
#
aaa
 authentication-scheme default
 authorization-scheme default
 accounting-scheme default
 domain default
 domain default_admin
 local-user admin password cipher %$%$K8m.Nt84DZ}e#<0`8bmE3Uw}%$%$
 local-user admin service-type http
#
firewall zone Local
 priority 15
#
interface Ethernet0/0/0
#
interface Ethernet0/0/1
#
interface Ethernet0/0/2
#
interface Ethernet0/0/3
#
interface Ethernet0/0/4
#
interface Ethernet0/0/5
#
interface Ethernet0/0/6
#
interface Ethernet0/0/7
#
interface GigabitEthernet0/0/0
 ip address 192.168.1.1 255.255.255.0
#
interface GigabitEthernet0/0/1
#
interface NULL0
#
user-interface con 0
 authentication-mode password
user-interface vty 0 4
user-interface vty 16 20
#
wlan ac
#
return
[R1]
4- 修改设备名字
[R11]sysname R1

5- 查看串行接口的ip
<R1>disp interface s2/0/0
Serial2/0/0 current state : UP
Line protocol current state : UP
Last line protocol up time : 2016-11-04 15:55:33 UTC-08:00
Description:HUAWEI, AR Series, Serial2/0/0 Interface
Route Port,The Maximum Transmit Unit is 1500, Hold timer is 10(sec)
Internet Address is 10.0.14.1/24
Link layer protocol is PPP
LCP opened, IPCP opened
Last physical up time   : 2016-11-04 15:55:31 UTC-08:00
Last physical down time : 2016-11-04 15:55:22 UTC-08:00
Current system time: 2016-11-04 16:07:27-08:00
Physical layer is synchronous, Virtualbaudrate is 64000 bps
Interface is DTE, Cable type is V11, Clock mode is TC
Last 300 seconds input rate 6 bytes/sec 48 bits/sec 0 packets/sec
Last 300 seconds output rate 6 bytes/sec 48 bits/sec 0 packets/sec

Input: 147 packets, 4764 bytes
  Broadcast:              0,  Multicast:              0
  Errors:                 0,  Runts:                  0
  Giants:                 0,  CRC:                    0

  Alignments:             0,  Overruns:               0
  Dribbles:               0,  Aborts:                 0
  No Buffers:             0,  Frame Error:            0

Output: 174 packets, 5276 bytes
  Total Error:            0,  Overruns:               0
  Collisions:             0,  Deferred:               0
    Input bandwidth utilization  :    0%
    Output bandwidth utilization :    0%

6- 查看各个接口的ip
<R1>disp ip int brie
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 4
The number of interface that is DOWN in Physical is 3
The number of interface that is UP in Protocol is 4
The number of interface that is DOWN in Protocol is 3

Interface                         IP Address/Mask      Physical   Protocol 
GigabitEthernet0/0/0              10.0.123.1/24        up         up       
GigabitEthernet0/0/1              unassigned           down       down     
GigabitEthernet1/0/0              unassigned           down       down     
LoopBack0                         10.0.1.1/24          up         up(s)    
NULL0                             unassigned           up         up(s)    
Serial2/0/0                       10.0.14.1/24         up         up       
Serial2/0/1                       unassigned           down       down   

7- 启动dhcp功能
[R1]dhcp en
Info: The operation may take a few seconds. Please wait for a moment.done.
[R1]int g0/0/1
[R1-GigabitEthernet0/0/1]ip address dhc 
[R1-GigabitEthernet0/0/1]ip address dhcp-alloc

8- 查看路由表
<R1>disp ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
         Destinations : 10       Routes : 10      

Destination/Mask    Proto   Pre  Cost      Flags NextHop         Interface

      127.0.0.0/8   Direct  0    0           D   127.0.0.1       InLoopBack0
      127.0.0.1/32  Direct  0    0           D   127.0.0.1       InLoopBack0
127.255.255.255/32  Direct  0    0           D   127.0.0.1       InLoopBack0
    192.168.0.0/16  Direct  0    0           D   192.168.240.1   GigabitEthernet
0/0/1
   192.168.12.0/24  Direct  0    0           D   192.168.12.1    GigabitEthernet
0/0/0
   192.168.12.1/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/0
 192.168.12.255/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/0
  192.168.240.1/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/1
192.168.255.255/32  Direct  0    0           D   127.0.0.1       GigabitEthernet
0/0/1
255.255.255.255/32  Direct  0    0           D   127.0.0.1       InLoopBack0

9- 添加静态路由
[R1]ip route-static 192.168.0.0 16 192.168.1.1

10- 取消静态路由
[R1]undo ip route-static 192.168.0.0 16 192.168.1.1

转载于:https://www.cnblogs.com/flyback/p/6034693.html