cnil在python_IL0389 电子纸（墨水屏）驱动

IL0389 电子纸(墨水屏)驱动

[复制链接]

image.png (262.85 KB, 下载次数: 0)

2020-5-14 09:35 上传

项目网站

'''

Copyright (c) 2020 Thomas Wilkinson

Permission is hereby granted, free of charge, to any person obtaining a copy

of this software and associated documentation files (the "Software"), to deal

in the Software without restriction, including without limitation the rights

to use, copy, modify, merge, publish, distribute, sublicense, and/or sell

copies of the Software, and to permit persons to whom the Software is

furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all

copies or substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR

IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,

FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE

AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER

LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,

OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE

SOFTWARE.

Written by Thomas Wilkinson - github.com/T-Wilko

'''

from micropython import const

from machine import SPI, Pin

from time import sleep_ms

import ustruct

## Display resolution

EPD_WIDTH = const(400)

EPD_HEIGHT = const(300)

# EPD_WIDTH must be divisible by 8 for this driver to work

## Display command addresses

PANEL_SETTING = const(0x00)

POWER_SETTING = const(0x01)

POWER_OFF = const(0x02)

POWER_OFF_SEQ_SET = const(0x03)

POWER_ON = const(0x04)

POWER_ON_MEASURE = const(0x05)

BOOSTER_SOFT_START_CONTROL = const(0x06)

DEEP_SLEEP_MODE = const(0x07)

START_TRANSMISSION_1 = const(0x10)

DATA_STOP = const(0x11)

DISP_REFRESH = const(0x12)

START_TRANSMISSION_2 = const(0x13)

PLL_CONTROL = const(0x30)

TEMP_CALIBRATION = const(0x40)

TEMP_SENSOR_SELECTION = const(0x41)

TEMP_SENSOR_WRITE = const(0x42)

TEMP_SENSOR_READ = const(0x43)

VCOM_DATA_INT_SETTING = const(0x50)

LOW_POWER_DETECT = const(0x51)

TCON_SETTING = const(0x60)

RES_SETTING = const(0x61)

GSST_SETTING = const(0x65)

REVISION = const(0x70)

GET_STATUS = const(0x71)

AUTO_MEASURE_VCOM = const(0x80)

VCOM_READ = const(0x81)

VCM_DC_SETTING = const(0x82)

#PARTIAL_WINDOW = const(0x90)

PARTIAL_IN = const(0x91)

PARTIAL_OUT = const(0x92)

PROGRAM_MODE = const(0xA0)

ACTIVE_PROG = const(0xA1)

READ_OTP = const(0xA2)

CASCADE_SETTING = const(0xE0)

POWER_SAVING = const(0xE3)

FORCE_TEMP = const(0xE5)

class EPD:

def __init__(self):

self.spi = SPI(1, baudrate=20000000, polarity=0, phase=0, sck=Pin(18), mosi=Pin(23), miso=Pin(19))

#self.spi = SPI(1, 10000000, sck=Pin(14), mosi=Pin(13), miso=Pin(12))

self.spi.init()

dc = Pin(27)

cs = Pin(5)

rst = Pin(14)

busy = Pin(4)

self.cs = cs

self.dc = dc

self.rst = rst

self.busy = busy

self.cs.init(self.cs.OUT, value=1)

self.dc.init(self.dc.OUT, value=0)

self.rst.init(self.rst.OUT, value=0)

self.busy.init(self.busy.IN)

self.width = EPD_WIDTH

self.height = EPD_HEIGHT

self.size = self.width * self.height // 8

self.buf = bytearray(self.size)

def clearBuffer(self):

self._command(b'\x24')

for i in range(0, len(self.buf)):

self.buf= 255

self._data(bytearray([self.buf]))

def displayBuffer(self, buf):

self._command(bytearray([START_TRANSMISSION_2]))

for i in range(0, len(buf)):

self._data(bytearray([buf]))

self._command(bytearray([DATA_STOP]))

self._command(bytearray([DISP_REFRESH]))

self.wait_until_idle()

def _command(self, command, data=None):

self.cs(1) # according to LOLIN_EPD

self.dc(0)

self.cs(0)

self.spi.write(command)

self.cs(1)

if data is not None:

self._data(data)

def _data(self, data):

self.cs(1) # according to LOLIN_EPD

self.dc(1)

self.cs(0)

self.spi.write(data)

self.cs(1)

def init(self):

#Reset EPD Driver IC

self.reset()

#Booster soft start

self._command(bytearray([BOOSTER_SOFT_START_CONTROL]), b'\x17\x17\x17')

#Power setting

self._command(bytearray([POWER_SETTING]), b'\x03\x00\x2B\x2B\x09')

#Power on

self._command(bytearray([POWER_ON]))

#Check busy pin and proceed if idle

self.wait_until_idle()

#Panel setting - B&W and full resolution

self._command(bytearray([PANEL_SETTING]), b'\x1F')

#PLL control - Set to 100Hz, default is 50Hz

self._command(bytearray([PLL_CONTROL]), b'\x3A')

#Resolution setting

self._command(bytearray([RES_SETTING]), b'\x01\x90\x01\x2C')

#VCM_DC setting - Currently set to -1V, default is -0.1V i.e. b'\x00'

self._command(bytearray([VCM_DC_SETTING]), b'\x12')

#VCOM and Data Interval setting

self._command(bytearray([VCOM_DATA_INT_SETTING]), b'\x87')

def wait_until_idle(self):

while self.busy == 0:

pass

return

def reset(self):

self.rst(1)

sleep_ms(1)

self.rst(0)

sleep_ms(10)

self.rst(1)

# draw the current frame memory and switch to the next memory area

def display_frame(self):

self._command(bytearray([DISPLAY_UPDATE_CONTROL_2]), b'\xC7')

self._command(bytearray([MASTER_ACTIVATION]))

self._command(bytearray([TERMINATE_FRAME_READ_WRITE]))

self.wait_until_idle()

# to wake call reset() or init()

def sleep(self):

self._command(bytearray([DEEP_SLEEP_MODE]))

self.wait_until_idle()