004、STM32CubeMX系列教程 LL库-PWM（控制蜂鸣器）

https://gitee.com/xushicheng1202/stm32-cube-mx_LL.git

这一章我们在前一章GPIO的工程修改。复制GPIO的工程，修改文件夹名。

1、使用STM32CubeMX配置定时器TIM1。

 2、配置时钟

3、设置路径、工程名称等

4、更改为LL库 

5、代码测试

5.1、main.c 文件 main 函数中，有 MX_TIM2_Init(); 的初始化函数，可以查看其初始化源码（保持stm32cubemx生成的不变，无需更改）

void MX_TIM2_Init(void)
{

  /* USER CODE BEGIN TIM2_Init 0 */

  /* USER CODE END TIM2_Init 0 */

  LL_TIM_InitTypeDef TIM_InitStruct = {0};
  LL_TIM_OC_InitTypeDef TIM_OC_InitStruct = {0};

  LL_GPIO_InitTypeDef GPIO_InitStruct = {0};
  /* Peripheral clock enable */
  LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_TIM2);

  /* USER CODE BEGIN TIM2_Init 1 */

  /* USER CODE END TIM2_Init 1 */
  TIM_InitStruct.Prescaler = 79;
  TIM_InitStruct.CounterMode = LL_TIM_COUNTERMODE_UP;
  TIM_InitStruct.Autoreload = 999;
  TIM_InitStruct.ClockDivision = LL_TIM_CLOCKDIVISION_DIV1;
  LL_TIM_Init(TIM2, &TIM_InitStruct);
  LL_TIM_DisableARRPreload(TIM2);
  LL_TIM_OC_EnablePreload(TIM2, LL_TIM_CHANNEL_CH1);
  TIM_OC_InitStruct.OCMode = LL_TIM_OCMODE_PWM1;
  TIM_OC_InitStruct.OCState = LL_TIM_OCSTATE_DISABLE;
  TIM_OC_InitStruct.OCNState = LL_TIM_OCSTATE_DISABLE;
  TIM_OC_InitStruct.CompareValue = 0xFF;
  TIM_OC_InitStruct.OCPolarity = LL_TIM_OCPOLARITY_HIGH;
  LL_TIM_OC_Init(TIM2, LL_TIM_CHANNEL_CH1, &TIM_OC_InitStruct);
  LL_TIM_OC_DisableFast(TIM2, LL_TIM_CHANNEL_CH1);
  LL_TIM_SetOCRefClearInputSource(TIM2, LL_TIM_OCREF_CLR_INT_NC);
  LL_TIM_DisableExternalClock(TIM2);
  LL_TIM_ConfigETR(TIM2, LL_TIM_ETR_POLARITY_NONINVERTED, LL_TIM_ETR_PRESCALER_DIV1, LL_TIM_ETR_FILTER_FDIV1);
  LL_TIM_SetTriggerOutput(TIM2, LL_TIM_TRGO_RESET);
  LL_TIM_DisableMasterSlaveMode(TIM2);
  /* USER CODE BEGIN TIM2_Init 2 */

  /* USER CODE END TIM2_Init 2 */
  LL_AHB2_GRP1_EnableClock(LL_AHB2_GRP1_PERIPH_GPIOA);
    /**TIM2 GPIO Configuration
    PA5     ------> TIM2_CH1
    */
  GPIO_InitStruct.Pin = PWM_BeepCtrl_Pin;
  GPIO_InitStruct.Mode = LL_GPIO_MODE_ALTERNATE;
  GPIO_InitStruct.Speed = LL_GPIO_SPEED_FREQ_HIGH;
  GPIO_InitStruct.OutputType = LL_GPIO_OUTPUT_PUSHPULL;
  GPIO_InitStruct.Pull = LL_GPIO_PULL_DOWN;
  GPIO_InitStruct.Alternate = LL_GPIO_AF_1;
  LL_GPIO_Init(PWM_BeepCtrl_GPIO_Port, &GPIO_InitStruct);

}

5.2、在初始化代码后配置使能一下 (TIM2, LL_TIM_CHANNEL_CH1)，使能和关闭PWM最好使用两步（虽然任一步也可以达到停止的效果） 。

  /* USER CODE BEGIN 2 */
  LL_TIM_CC_EnableChannel(TIM2, LL_TIM_CHANNEL_CH1); // 开启PWM驱动蜂鸣器1-2：Enable capture/compare channels.
  LL_TIM_EnableCounter(TIM2);                        // 开启PWM驱动蜂鸣器2-2：TIM_LL_EF_Time_Base Time Base configuration

  LL_mDelay(5000);
  LL_TIM_CC_DisableChannel(TIM2, LL_TIM_CHANNEL_CH1); // 关闭PWM停止蜂鸣器1-2：Disable capture/compare channels.
  LL_TIM_DisableCounter(TIM2);                        // 关闭PWM停止蜂鸣器2-2：Disable timer counter.

  /* USER CODE END 2 */