RationalDMIS2024向量创建测量（样例点测量）

1.设置测量深度

2.设置样例点间隔

方法一：

测点管理窗口，点击“工作平面”切换为“向量创建”

登录后复制

F(P-6)=FEAT/CIRCLE,INNER,CART,56.0000,27.2872,35.0000,-0.0000,-0.0000,1.0000, 10.0000

$$ Measurement points are created through nominal points
$$ CALL/M(EASI_CLEARPLN_GOTO), 1, 48.0029, 27.5035, 56.4950
RMEAS/CIRCLE, F(P-6), 5, VECBLD, 3.0000, 3
  GOTO/CART,   48.0029, 27.5035, 56.4950
  RPTMEAS/CART, 48.0029, 27.5035, 35.0000, 0.0000, 0.0000, 1.0000
  RPTMEAS/CART, 59.8112, 20.2533, 35.0000, 0.0000, 0.0000, 1.0000
  RPTMEAS/CART, 60.1859, 34.1047, 35.0000, 0.0000, 0.0000, 1.0000
  GOTO/CART,   54.4956, 27.3279, 38.4950
  PTMEAS/CART, 51.0018, 27.4224, 32.0000,  0.9996, -0.0270,  0.0000
  PTMEAS/CART, 54.3269, 22.5754, 32.0000,  0.3346,  0.9424,  0.0000
  PTMEAS/CART, 59.9641, 24.2399, 32.0000, -0.7928,  0.6094,  0.0000
  PTMEAS/CART, 60.1231, 30.1156, 32.0000, -0.8246, -0.5657, -0.0000
  PTMEAS/CART, 54.5841, 32.0825, 32.0000,  0.2832, -0.9591, -0.0000
  GOTO/CART,   55.5739, 28.7304, 56.4950
ENDMES

• 1.
• 2.
• 3.
• 4.
• 5.
• 6.
• 7.
• 8.
• 9.
• 10.
• 11.
• 12.
• 13.
• 14.
• 15.
• 16.
• 17.

方法二：

元素产生测点窗口向量创建选项；点击产生测量点后，将会把测点管理设置为向量创建状态；

F(P-7)=FEAT/CIRCLE,INNER,CART,72.0000,55.0000,35.0000,0.0000,0.0000,1.0000, 10.0000

SNSET/APPRCH, 2.0000

SNSET/RETRCT, 2.0000

SNSET/DEPTH, 3.0000

SNSET/SEARCH, 5.0000

SNSET/CLRSRF, FA(PLN2), 20.0000

CALL/M(EASI_CLEARPLN_GOTO), 1, 64.0000, 55.0000, 35.0000

RMEAS/CIRCLE, F(P-7), 5, VECBLD, 3.0000, 3

RPTMEAS/CART, 64.0000, 55.0000, 35.0000, 0.0000, 0.0000, 1.0000

RPTMEAS/CART, 76.0000, 48.0718, 35.0000, 0.0000, 0.0000, 1.0000

RPTMEAS/CART, 76.0000, 61.9282, 35.0000, 0.0000, 0.0000, 1.0000

GOTO/CART, 70.4950, 55.0000, 38.4950

PTMEAS/CART, 67.0000, 55.0000, 32.0000, 1.0000, -0.0000, -0.0000

PTMEAS/CART, 70.4549, 59.7553, 32.0000, 0.3090, -0.9511, 0.0000

PTMEAS/CART, 76.0451, 57.9389, 32.0000, -0.8090, -0.5878, 0.0000

PTMEAS/CART, 76.0451, 52.0611, 32.0000, -0.8090, 0.5878, -0.0000

PTMEAS/CART, 70.4549, 50.2447, 32.0000, 0.3090, 0.9511, -0.0000

ENDMES

原创作者: u_14941238 转载于: https://blog.51cto.com/u_14941238/11457183