nRF24L01无线通信模块使用简介（接收端）

书接上回，上篇博客给出了nRF24L01搭配C51单片机进行无线通信的发送端代码。这里给出接收端代码。

接收端
接收端的功能主要是接收发送端发来的数据，并将数据通过串口发送给上位机。
发送端接收端正常通信后，在PC上使用常用的串口读取软件，就可以看到发送过来的数据了，串口的波特率设置在9600。

与C51连线
接收端nRF24L01模块与C51连线与发送端相同。

下面还是废话少说直接给出代码

#include <reg51.h>
#include <string.h>

#define uchar unsigned char
#define uint  unsigned int
#define ulong unsigned long

/***************************************************/
#define TX_ADR_WIDTH   5  // 5字节宽度的发送/接收地址
#define TX_PLOAD_WIDTH 15  // 数据通道有效数据宽度

sbit LED = P2^1;
//sbit LED = P3^3;

uchar code TX_ADDRESS[5] = {
   0x34,0x43,0x10,0x10,0x01};  // 定义一个静态发送地址
uchar RX_BUF[TX_ADR_WIDTH];
uchar TX_BUF[TX_ADR_WIDTH];
uchar flag;
uchar DATA = 0x01;
uchar bdata sta;
sbit  RX_DR     = sta^6;
sbit  TX_DS     = sta^5;
sbit  MAX_RT = sta^4;

sbit CE =  P1^5;
sbit CSN=  P1^4;
sbit SCK=  P1^3;
sbit MOSI= P1^2;
sbit MISO= P1^1;
sbit IRQ = P1^0;

// SPI(nRF24L01) commands
#define READ_REG    0x00  // Define read command to register
#define WRITE_REG   0x20  // Define write command to register
#define RD_RX_PLOAD 0x61  // Define RX payload register address
#define WR_TX_PLOAD 0xA0  // Define TX payload register address
#define FLUSH_TX    0xE1  // Define flush TX register command
#define FLUSH_RX    0xE2  // Define flush RX register command
#define REUSE_TX_PL 0xE3  // Define reuse TX payload register command
#define NOP         0xFF  // Define No Operation, might be used to read status register

// SPI(nRF24L01) registers(addresses)
#define CONFIG      0x00  // 'Config' register address
#define EN_AA       0x01  // 'Enable Auto Acknowledgment' register address
#define EN_RXADDR   0x02  // 'Enabled RX addresses' register address
#define SETUP_AW    0x03  // 'Setup address width' register address
#define SETUP_RETR  0x04  // 'Setup Auto. Retrans' register address
#define RF_CH       0x05  // 'RF channel' register address
#define RF_SETUP    0x06  // 'RF setup' register address
#define STATUS      0x07  // 'Status' register address
#define OBSERVE_TX  0x08  // 'Observe TX' register address
#define CD          0x09  // 'Carrier Detect' register address
#define RX_ADDR_P0  0x0A  // 'RX address pipe0' register address
#define RX_ADDR_P1  0x0B  // 'RX address pipe1' register address
#define RX_ADDR_P2  0x0C  // 'RX address pipe2' register address
#define RX_ADDR_P3  0x0D  // 'RX address pipe3' register address
#define RX_ADDR_P4  0x0E