Rockchip RK3588 kernel dts解析之regulator-fixed

Rockchip RK3588 kernel dts解析之regulator-fixed

regulator-fixed通常用于定义电压固定的regulator，或由某个GPIO开关控制的regulator。
如rk3588-evb1-lp4.dtsi中定义的

//给PCIE2.0用的0.85v电源的模拟regulator
pcie20_avdd0v85: pcie20-avdd0v85 {
		compatible = "regulator-fixed";
		regulator-name = "pcie20_avdd0v85";
		regulator-boot-on;
		regulator-always-on;
		regulator-min-microvolt = <850000>;
		regulator-max-microvolt = <850000>;
		vin-supply = <&avdd_0v85_s0>;
	};
	//给PCIE2.0用的1.8v电源的模拟regulator
	pcie20_avdd1v8: pcie20-avdd1v8 {
		compatible = "regulator-fixed";
		regulator-name = "pcie20_avdd1v8";
		regulator-boot-on;
		regulator-always-on;
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <1800000>;
		vin-supply = <&avcc_1v8_s0>;
	};
	//给PCIE3.0用的0.75v电源的模拟regulator
	pcie30_avdd0v75: pcie30-avdd0v75 {
		compatible = "regulator-fixed";
		regulator-name = "pcie30_avdd0v75";
		regulator-boot-on;
		regulator-always-on;
		regulator-min-microvolt = <750000>;
		regulator-max-microvolt = <750000>;
		vin-supply = <&avdd_0v75_s0>;
	};
	//给PCIE3.0用的1.8v电源的模拟regulato
	pcie30_avdd1v8: pcie30-avdd1v8 {
		compatible = "regulator-fixed";
		regulator-name = "pcie30_avdd1v8";
		regulator-boot-on;
		regulator-always-on;
		regulator-min-microvolt = <1800000>;
		regulator-max-microvolt = <1800000>;
		vin-supply = <&avcc_1v8_s0>;
	};
	//TYPE-C的vbus5v0电源，使用GPIO4_D0来控制这个电源
	vbus5v0_typec: vbus5v0-typec {
		compatible = "regulator-fixed";
		regulator-name = "vbus5v0_typec";
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		enable-active-high;
		gpio = <&gpio4 RK_PD0 GPIO_ACTIVE_HIGH>;
		vin-supply = <&vcc5v0_usb>;
		pinctrl-names = "default";
		pinctrl-0 = <&typec5v_pwren>;
	};
	//	LCD的电源控制，使用GPIO1_C4来控制，开机后默认打开电源
	vcc3v3_lcd_n: vcc3v3-lcd0-n {
		compatible = "regulator-fixed";
		regulator-name = "vcc3v3_lcd0_n";
		regulator-boot-on;
		enable-active-high;
		gpio = <&gpio1 RK_PC4 GPIO_ACTIVE_HIGH>;
		vin-supply = <&vcc_1v8_s0>;
	};
	//PCIE的3v3电源，使用GPIO3_C3来控制
	vcc3v3_pcie30: vcc3v3-pcie30 {
		compatible = "regulator-fixed";
		regulator-name = "vcc3v3_pcie30";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		enable-active-high;
		gpios = <&gpio3 RK_PC3 GPIO_ACTIVE_HIGH>;
		startup-delay-us = <5000>;
		vin-supply = <&vcc12v_dcin>;
	};
	//USB host 5V电源的控制，使用GPIO4_B0来控制，可以在驱动中控制这个vcc5v0_host这个regulator
	vcc5v0_host: vcc5v0-host {
		compatible = "regulator-fixed";
		regulator-name = "vcc5v0_host";
		regulator-boot-on;
		regulator-always-on;
		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;
		enable-active-high;
		gpio = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
		vin-supply = <&vcc5v0_usb>;
		pinctrl-names = "default";
		pinctrl-0 = <&vcc5v0_host_en>;
	};
	//camera的mipi csi0的电源控制，使用GPIO1_B1来控制
	vcc_mipicsi0: vcc-mipicsi0-regulator {
		compatible = "regulator-fixed";
		gpio = <&gpio1 RK_PB1 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "default";
		pinctrl-0 = <&mipicsi0_pwr>;
		regulator-name = "vcc_mipicsi0";
		enable-active-high;
	};
	//camera的mipi csi1的电源控制，使用GPIO1_B2来控制
	vcc_mipicsi1: vcc-mipicsi1-regulator {
		compatible = "regulator-fixed";
		gpio = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "default";
		pinctrl-0 = <&mipicsi1_pwr>;
		regulator-name = "vcc_mipicsi1";
		enable-active-high;
	};
	//camera的mipi dcphy0的电源控制，使用GPIO2_C4来控制
	vcc_mipidcphy0: vcc-mipidcphy0-regulator {
		compatible = "regulator-fixed";
		gpio = <&gpio2 RK_PC4 GPIO_ACTIVE_HIGH>;
		pinctrl-names = "default";
		pinctrl-0 = <&mipidcphy0_pwr>;
		regulator-name = "vcc_mipidcphy0";
		enable-active-high;
	};

如何使用regulator-fixed来实现使用GPIO控制某个电源开关，并且这个GPIO不属于某个特定驱动模块的，希望在开机时尽快输出高低电平来控制电源，具体可以参考如下：
以GPIO2_A1需要配置为高电平为例

/ {
	foo_name: foo-name {
		compatible = "regulator-fixed";
		pinctrl-names = "default";
		pinctrl-0 = <&gpio_foo>;
		regulator-name = "vcc-foo";
		regulator-always-on;
	};
};

&pinctrl {
	gpio-foo {
		gpio_foo: gpio-foo {
			rockchip,pins = <2 RK_PA1 RK_FUNC_GPIO &pcfg_output_high>;
		};
	};
};