ADS 报错信息整理

最新推荐文章于 2024-12-15 18:22:53 发布

久坐三年寒石亦暖

最新推荐文章于 2024-12-15 18:22:53 发布

阅读量1.9w

点赞数 12

文章标签： ADS

本文链接：https://blog.csdn.net/weixin_45055687/article/details/102826693

版权

2019.10.30

仿真得到的警告信息，虽然有结果，但还是想解决报错信息看看是什么

Simulation Messages

Warning detected by hpeesofsim in LinearCollapse '_2_' during analysis.
    LinearCollapse is disabled since there is 'HB'analysis present.

//在分析期间，hpeesofsim在LinearCollapse’2’中检测到警告。
因为存在“ HB”分析，所以禁用LinearCollapse。

Warning detected by hpeesofsim in topology check during circuit set up.
    Number of nodes with no DC path to ground (topology corrected): 2

//hpeesofsim在电路设置过程中的拓扑检查中检测到警告。
无直流接地路径的节点数（已校正拓扑）：2;有节点没有直流到地，可忽略（应该是我的两个通孔）

Warning detected by hpeesofsim during circuit set up.
    analysis `S1' is not found for ParamSweep component `Sweep1'.

//hpeesofsim在电路设置过程中检测到警告。
找不到ParamSweep组件“ Sweep1”的分析“ S1”。

Warning detected by hpeesofsim during DC analysis `SP1'.
    Capacitor `FP1.C5' C=-3e-12 is negative.

//hpeesofsim在DC分析“ SP1”期间检测到警告。
电容器FP1.C5 C = -3e-12为负。;直流分析电容为负数

Warning detected by hpeesofsim during DC analysis `SP1'.
    Capacitor `FP1.C6' C=-3e-12 is negative.

//hpeesofsim在DC分析“ SP1”期间检测到警告。
电容FP1.C6 C = -3e-12为负。

Warning detected by hpeesofsim during HB analysis `HB1'.
    The simulation converged with a current relative
    tolerance of 1.00e-06. This is the best solution that can be achieved
    using the given simulation setup.
    The circuit was NOT able to achieve the target
    current relative tolerance of 1.00e-06.

//hpeesofsim在HB分析“ HB1”期间检测到警告。
模拟与当前相对收敛
公差为1.00e-06。这是可以实现的最佳解决方案
使用给定的模拟设置。
电路无法达到目标
当前的相对公差为1.00e-06。

Warning detected by hpeesofsim during HB analysis `HB1'.
Warning detected by hpeesofsim during HB analysis `HB1'.
    'Sweep1[1].HB1[2/2]' ( vgs=200e-03 ) did not converge -- associated data will be identified with '<invalid>' flag in the dataset.

//hpeesofsim在HB分析“ HB1”期间检测到警告。
‘Sweep1 [1] .HB1 [2/2]’（vgs = 200e-03）没有收敛-关联的数据将在数据集中用’'标志标识。

Warning detected by hpeesofsim during HB analysis `HB1'.
    Convergence hints:
    o Use sweep in HB controller (internal sweep) if it is not frequency related.
    o Enable Regenerate Initial Guess for ParamSweep.
    o Try TAHB (transient assisted HB).
    o The final residual is small. Increase Max Iterations or relax tolerances.
    o Set Matrix Re-use to Robust with the direct solver.
    o Select the Krylov solver.
    o Increase the Fundamental Oversample.
    o Check the circuit/devices around the nodes in solver convergence summary.
    o Act upon warning messages and topology errors.

hpeesofsim在HB分析“ HB1”期间检测到警告。
收敛提示：
o如果与频率无关，请在HB控制器中使用扫描（内部扫描）。
o为ParamSweep启用重新生成初始猜测。
o尝试使用TAHB（瞬态辅助HB）。
o最终残差很小。增加最大迭代次数或放宽公差。
o使用直接求解器将“矩阵重用”设置为“稳健”。
o选择Krylov求解器。
o增加基本过采样。
o在求解器收敛摘要中检查节点周围的电路/设备。
o根据警告消息和拓扑错误采取行动。