野火stm32mini第四章----------------金沙滩单片机上面的数码管

最新推荐文章于 2023-08-18 13:27:08 发布

乌拉_乌拉_乌拉

最新推荐文章于 2023-08-18 13:27:08 发布

阅读量369

点赞数

文章标签：单片机 stm32 嵌入式硬件

本文链接：https://blog.csdn.net/weixin_47454452/article/details/126919930

版权

第一步先拼接连线

STM32上面的PA2-PA9就是P00到P07 是段选择引脚
B0-B3就是P10到P13
A0 -----p00 ----1-a
A1 -----p01 ----0-b
A2 -----p02 ----0-c
A3 -----p03 ----1-d
A4 -----p04 ----1-e
A5 -----p05 ----1-f
A6 -----p06 ----1-g
A7 -----p07 ----1-dp

1 = 0xF9 = 1111 1001

位选
B0 -----p10
B1 -----p11
B2 -----p12
B3 -----p13
B4-----P14 —ENLED

#include "main.h"

const uint32_t SEG_SegPins[] =
{
		GPIO_PIN_0,
		GPIO_PIN_1,
		GPIO_PIN_2,
		GPIO_PIN_3,
		GPIO_PIN_4,
		GPIO_PIN_5,
		GPIO_PIN_6,
		GPIO_PIN_7,

};

const uint8_t LedChar[] = {
	0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,
	0x80,0x90,0x88,0x83,0xc6,0xa1,0x86,0x8e  //数码管真值表
};

void SystemClock_Config(void);
void Seg_Init(void);
void Seg_DisplaySingleDigit(uint32_t n);

int main(int argc, char **argv) {

	HAL_Init();
	SystemClock_Config();
	//初始化数码管
	Seg_Init();

	while(1)
	{
		int i = 0;
		for (i = 0; i < 16;i++) {
			GPIOWRITE(GPIOA,LedChar[i]);
			HAL_Delay(5000);
		}
	}
	return 0;
}

void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    Error_Handler();
  }
  /** Initializes the CPU, AHB and APB buses clocks
  */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;

  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0) != HAL_OK)
  {
    Error_Handler();
  }
}

void Seg_Init(void)
{
	 GPIO_InitTypeDef GPIO_InitStruct = {0};
	 GPIO_InitTypeDef gpioinit;

	  /* GPIO Ports Clock Enable */
	  __HAL_RCC_GPIOA_CLK_ENABLE();
	  __HAL_RCC_GPIOB_CLK_ENABLE();

	  uint32_t i;
	  //gpioinit.Mode = GPIO_MODE_OUTPUT_PP;
	  //gpioinit.Speed = GPIO_SPEED_FREQ_LOW;

	  for (i = 0; i <9; i++) {
	  		gpioinit.Pin = SEG_SegPins[i];
	  		//上来先全灭
	  		HAL_GPIO_WritePin(GPIOA, SEG_SegPins[i], GPIO_PIN_RESET);
	  		HAL_GPIO_Init(GPIOA, &gpioinit);
	  	}

	  /*Configure GPIO pin Output Level */
	  HAL_GPIO_WritePin(GPIOB, GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_4, GPIO_PIN_RESET);

	  /*Configure GPIO pin Output Level */
	  HAL_GPIO_WritePin(GPIOB, GPIO_PIN_3, GPIO_PIN_SET);

	  GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3|GPIO_PIN_4|GPIO_PIN_5
	                            |GPIO_PIN_6|GPIO_PIN_7;
	  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
	  GPIO_InitStruct.Pull = GPIO_NOPULL;
	  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
	  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

	  /*Configure GPIO pins : PB0 PB1 PB2 PB3
	                           ENLED_Pin */
	  GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3
	                          |GPIO_PIN_4;
	  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
	  GPIO_InitStruct.Pull = GPIO_NOPULL;
	  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
	  HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);

}

void GPIOWRITE(GPIO_TypeDef* GPIOx,uint8_t dat)
{
	GPIOx->ODR = dat | ((GPIOx->ODR)&0xff00);
}

void Error_Handler(void)
{

}

#ifdef  USE_FULL_ASSERT
void assert_failed(uint8_t *file, uint32_t line)
{

}
#endif /* USE_FULL_ASSERT */