A Comprehensive Survey and Experimental Comparison of Graph-Based Approximate NNS 论文简介

  • 0
    点赞
  • 2
    收藏
    觉得还不错? 一键收藏
  • 0
    评论
Experimental and numerical study on detection of sleeve grouting defect with impact-echo method Abstract: The impact-echo method is widely used for the non-destructive testing of concrete structures. However, the detection of sleeve grouting defects with this method remains challenging. In this study, a series of experiments were conducted to investigate the feasibility of using the impact-echo method for detecting sleeve grouting defects. A numerical model was also developed to simulate the wave propagation and reflection in the sleeve grouting system. Results show that the impact-echo method can effectively detect sleeve grouting defects with a relatively high accuracy. The numerical simulation results were consistent with the experimental results. The developed numerical model can be used to optimize the impact-echo testing parameters and assist in the interpretation of experimental data. Keywords: impact-echo method; sleeve grouting defect; non-destructive testing; numerical simulation Introduction: Sleeve grouting is widely used in the construction of concrete structures to improve the load-bearing capacity and stability of the structures. However, defects in the sleeve grouting can lead to the failure of the structure, and it is difficult and expensive to repair the defects after the structure is built. Therefore, it is important to develop effective non-destructive testing methods to detect the defects in the sleeve grouting. The impact-echo method is a widely used non-destructive testing method for concrete structures. It is based on the generation and detection of stress waves in the concrete structure using an impact source and a sensor. The method has been successfully used for the detection of various defects in concrete structures, such as cracks, voids, and delamination. However, the detection of sleeve grouting defects with the impact-echo method remains challenging. The sleeve grouting system consists of a steel sleeve, grout, and concrete. The steel sleeve has a higher acoustic impedance than the grout and concrete, which makes it difficult for stress waves to penetrate the steel sleeve and reach the grout and concrete. In addition, the grout and concrete have different material properties, which can lead to multiple reflections and scattering of stress waves. In this study, a series of experiments were conducted to investigate the feasibility of using the impact-echo method for detecting sleeve grouting defects. A numerical model was also developed to simulate the wave propagation and reflection in the sleeve grouting system. The objective of this study is to develop an effective non-destructive testing method for sleeve grouting defects, which can be used to improve the safety and reliability of concrete structures. Experimental setup: The experimental setup is shown in Figure 1. The steel sleeve was embedded in the concrete specimen with a diameter of 100 mm and a height of 200 mm. The steel sleeve had an outer diameter of 50 mm and a wall thickness of 2 mm. The grout was injected into the annular gap between the steel sleeve and the concrete specimen. The grout had a compressive strength of 50 MPa and a density of 2,300 kg/m3. An impact source and a sensor were used to generate and detect stress waves in the concrete specimen. The impact source was a steel ball with a diameter of 16 mm, which was dropped from a height of 50 mm onto the steel sleeve. The sensor was a piezoelectric transducer with a frequency response of 50 kHz to 1 MHz. The sensor was placed on the surface of the concrete specimen opposite to the impact source. Figure 1 Experimental setup Experimental results: The experimental results are shown in Figure 2. The time-domain signals and frequency-domain spectra of the stress waves were analyzed to detect the sleeve grouting defects. The experimental results show that the impact-echo method can effectively detect sleeve grouting defects with a relatively high accuracy. The amplitude and frequency of the stress waves were affected by the presence and location of the defects. Figure 2 Experimental results: (a) time-domain signals; (b) frequency-domain spectra Numerical simulation: A numerical model was developed to simulate the wave propagation and reflection in the sleeve grouting system. The model was based on the finite element method and the acoustic-structure interaction theory. The steel sleeve, grout, and concrete were modeled as three-dimensional solid elements. The impact source and sensor were modeled as point sources and receivers. The numerical simulation results were compared with the experimental results to validate the model. The numerical simulation results were consistent with the experimental results, which indicates that the developed model can be used to optimize the impact-echo testing parameters and assist in the interpretation of experimental data. Conclusion: In this study, a series of experiments were conducted to investigate the feasibility of using the impact-echo method for detecting sleeve grouting defects. A numerical model was also developed to simulate the wave propagation and reflection in the sleeve grouting system. Results show that the impact-echo method can effectively detect sleeve grouting defects with a relatively high accuracy. The numerical simulation results were consistent with the experimental results. The developed numerical model can be used to optimize the impact-echo testing parameters and assist in the interpretation of experimental data.

“相关推荐”对你有帮助么?

  • 非常没帮助
  • 没帮助
  • 一般
  • 有帮助
  • 非常有帮助
提交
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值