nodeMcu(esp8266)连接wifi(2.4G)/NodeMcu+oled(ssd1306)库例程

测试环境基于:vscode+platformIO IDE平台
( a awsome tool to develop almost all embedded boards)

testCode

the libraries:

• <ESP8266WiFi.h>
• <Arduino.h>

the funcitons:

• WiFi.begin()
• WiFi.status()
• WiFi.localIP()

#include <Arduino.h>
#include <ESP8266WiFi.h>
#include <ESP8266WiFiMulti.h>
//#include <ESP8266HTTPClient.h>
//设置两个宏定义用于WiFi名和密码(修改为自身环境(比手机热点wifi)
#define WIFINAME "belldandy"
#define WIFIPW "11223344"
// nodemcu只能够链接到2.4G频段的wifi(或者说,默认是连不到5Ghz的WiFi的,这一点要注意!)
void setup()
{
    // put your setup code here, to run once:
    pinMode(LED_BUILTIN, OUTPUT);
    Serial.begin(115200);
    Serial.println("");
    WiFi.begin(WIFINAME, WIFIPW);
    Serial.print("Connecting wifi..");
    while (WiFi.status() != WL_CONNECTED)
    {
        delay(500);
        Serial.print(".");
    }
    Serial.println();
    Serial.print("Connected,IP Address:");
    Serial.println(WiFi.localIP());
}

void loop()
{
    // put your main code here, to run repeatedly:
    Serial.println("in loop()");
    delay(1e4);
}

platformIO bring you a brand embedded development experience.

process(build and upload)

Executing task in folder IOT: C:\Users\cxxu.platformio\penv\Scripts\platformio.exe run --target upload <

Processing nodemcuv2 (platform: espressif8266; board: nodemcuv2; framework: arduino)
--------------------------------------------------------------------------------Verbose mode can be enabled via -v, --verbose option
CONFIGURATION: https://docs.platformio.org/page/boards/espressif8266/nodemcuv2.html
PLATFORM: Espressif 8266 (3.2.0) > NodeMCU 1.0 (ESP-12E Module)
HARDWARE: ESP8266 80MHz, 80KB RAM, 4MB Flash
PACKAGES:

• framework-arduinoespressif8266 3.30002.0 (3.0.2)
• tool-esptool 1.413.0 (4.13)
• tool-esptoolpy 1.30000.201119 (3.0.0)
• tool-mklittlefs 1.203.210628 (2.3)
• tool-mkspiffs 1.200.0 (2.0)
• toolchain-xtensa 2.100300.210717 (10.3.0)
  LDF: Library Dependency Finder -> http://bit.ly/configure-pio-ldf
  LDF Modes: Finder ~ chain, Compatibility ~ soft
  Found 40 compatible libraries
  Scanning dependencies…
  Dependency Graph
  |-- 3.1.0
  |-- 6.18.4
  |-- 1.2
  | |-- 1.0
  |-- 1.0
  Building in release mode
  Retrieving maximum program size .pio\build\nodemcuv2\firmware.elf
  Checking size .pio\build\nodemcuv2\firmware.elf
  Advanced Memory Usage is available via “PlatformIO Home > Project Inspect”
  RAM: [=== ] 34.3% (used 28136 bytes from 81920 bytes)
  Flash: [=== ] 25.7% (used 267973 bytes from 1044464 bytes)
  Configuring upload protocol…
  AVAILABLE: espota, esptool
  CURRENT: upload_protocol = esptool
  Looking for upload port…
  Auto-detected: COM3
  Uploading .pio\build\nodemcuv2\firmware.bin
  esptool.py v3.0
  Serial port COM3
  Connecting…
  Chip is ESP8266EX
  Features: WiFi
  Crystal is 26MHz
  MAC: e8:db:84:9c:47:bd
  Uploading stub…
  Running stub…
  Stub running…
  Configuring flash size…
  Compressed 272128 bytes to 199704…
  Writing at 0x00000000… (7 %)
  Writing at 0x00004000… (15 %)
  Writing at 0x00008000… (23 %)
  Writing at 0x0000c000… (30 %)
  Writing at 0x00010000… (38 %)
  Writing at 0x00014000… (46 %)
  Writing at 0x00018000… (53 %)
  Writing at 0x0001c000… (61 %)
  Writing at 0x00020000… (69 %)
  Writing at 0x00024000… (76 %)
  Writing at 0x00028000… (84 %)
  Writing at 0x0002c000… (92 %)
  Writing at 0x00030000… (100 %)
  Wrote 272128 bytes (199704 compressed) at 0x00000000 in 17.9 seconds (effective
  121.7 kbit/s)…
  Hash of data verified.

Leaving…
Hard resetting via RTS pin…
========================= [SUCCESS] Took 25.99 seconds =========================
Terminal will be reused by tasks, press any key to close it.

Executing task in folder IOT: C:\Users\cxxu.platformio\penv\Scripts\platformio.exe run --target upload <

Processing nodemcuv2 (platform: espressif8266; board: nodemcuv2; framework: arduino)
--------------------------------------------------------------------------------Verbose mode can be enabled via -v, --verbose option
CONFIGURATION: https://docs.platformio.org/page/boards/espressif8266/nodemcuv2.html
PLATFORM: Espressif 8266 (3.2.0) > NodeMCU 1.0 (ESP-12E Module)
HARDWARE: ESP8266 80MHz, 80KB RAM, 4MB Flash
PACKAGES:

• framework-arduinoespressif8266 3.30002.0 (3.0.2)
• tool-esptool 1.413.0 (4.13)
• tool-esptoolpy 1.30000.201119 (3.0.0)
• tool-mklittlefs 1.203.210628 (2.3)
• tool-mkspiffs 1.200.0 (2.0)
• toolchain-xtensa 2.100300.210717 (10.3.0)
  LDF: Library Dependency Finder -> http://bit.ly/configure-pio-ldf
  LDF Modes: Finder ~ chain, Compatibility ~ soft
  Found 40 compatible libraries
  Scanning dependencies…
  Dependency Graph
  |-- 3.1.0
  |-- 6.18.4
  |-- 1.2
  | |-- 1.0
  |-- 1.0
  Building in release mode
  Compiling .pio\build\nodemcuv2\src\wifi_connect.cpp.o
  Linking .pio\build\nodemcuv2\firmware.elf
  Retrieving maximum program size .pio\build\nodemcuv2\firmware.elf
  Checking size .pio\build\nodemcuv2\firmware.elf
  Advanced Memory Usage is available via “PlatformIO Home > Project Inspect”
  RAM: [=== ] 34.3% (used 28136 bytes from 81920 bytes)
  Flash: [=== ] 25.7% (used 267989 bytes from 1044464 bytes)
  Building .pio\build\nodemcuv2\firmware.bin
  Creating BIN file “.pio\build\nodemcuv2\firmware.bin” using “C:\Users\cxxu.platformio\packages\framework-arduinoespressif8266\bootloaders\eboot\eboot.elf” and
  “.pio\build\nodemcuv2\firmware.elf”
  Configuring upload protocol…
  AVAILABLE: espota, esptool
  CURRENT: upload_protocol = esptool
  Looking for upload port…
  Auto-detected: COM3
  Uploading .pio\build\nodemcuv2\firmware.bin
  esptool.py v3.0
  Serial port COM3
  Connecting…
  Chip is ESP8266EX
  Features: WiFi
  Crystal is 26MHz
  MAC: e8:db:84:9c:47:bd
  Uploading stub…
  Running stub…
  Stub running…
  Configuring flash size…
  Compressed 272144 bytes to 199703…
  Writing at 0x00000000… (7 %)
  Writing at 0x00004000… (15 %)
  Writing at 0x00008000… (23 %)
  Writing at 0x0000c000… (30 %)
  Writing at 0x00010000… (38 %)
  Writing at 0x00014000… (46 %)
  Writing at 0x00018000… (53 %)
  Writing at 0x0001c000… (61 %)
  Writing at 0x00020000… (69 %)
  Writing at 0x00024000… (76 %)
  Writing at 0x00028000… (84 %)
  Writing at 0x0002c000… (92 %)
  Writing at 0x00030000… (100 %)
  Wrote 272144 bytes (199703 compressed) at 0x00000000 in 17.9 seconds (effective
  121.9 kbit/s)…
  Hash of data verified.

Leaving…
Hard resetting via RTS pin…
========================= [SUCCESS] Took 29.38 seconds =========================
Terminal will be reused by tasks, press any key to close it.

NodeMcu+oled(ssd1306)库例程

arduinoIDE

安装库：

第一个库没用过.

vscode + platform