STM32标准库定时器（TIM3）

yx3146006361

于 2024-04-15 08:55:29 发布

阅读量170

点赞数 1

文章标签： stm32 嵌入式硬件单片机

本文链接：https://blog.csdn.net/yx3146006361/article/details/137764423

版权

//timer.c
#include "timer.h"
#include "led.h"
void TIM3_Init(u16 arr,u16 psc)
{
 TIM_TimeBaseInitTypeDef  TIM_TimeBaseStructure;  
 NVIC_InitTypeDef NVIC_InitStructure;

 TIM_TimeBaseStructure.TIM_Period=arr;
 TIM_TimeBaseStructure.TIM_Prescaler=psc;
 TIM_TimeBaseStructure.TIM_ClockDivision=TIM_CKD_DIV1;
 TIM_TimeBaseStructure.TIM_CounterMode=TIM_CounterMode_Up;
 TIM_BaseInit(TIM3,&TIM_TimeBaseStructure);

 TIM_ITConfig(TIM3,TIM_IT_Updata,ENABLE);

 //中断优先级NVIC设置
 NVIC_InitStructure.NVIC_IRQChannel=TIM3_IRQn;   //TIM3中断
 NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority=0;   //先占优先级0级
 NVIC_InitStructure.NVIC_IRQChannelSubPriority=3;     //从优先级3级
 NVIC_InitStructure.NVIC_IRQChannelCmd=ENABLE;  //IRQ通道被使
 
 NVIC_Init(&NVIC_InitStructure);  //初始化NVIC寄存器

 TIM_Cmd(TIM3,ENABLE);       //使能TIM3
 
}

//定时器3中断服务程序
void TIM3_IRQHandler(void)   //TIM3中断
{
	if (TIM_GetITStatus(TIM3, TIM_IT_Update) != RESET)  //检查TIM3更新中断发生与否
		{
		TIM_ClearITPendingBit(TIM3, TIM_IT_Update  );  //清除TIMx更新中断标志 
		LED1=!LED1;
		}
}

  //led.c
void LED_Init(void)
{
 
 GPIO_InitTypeDef  GPIO_InitStructure;
 	
 RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB|RCC_APB2Periph_GPIOE, ENABLE);	 //使能PB,PE端口时钟
	
 GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;				 //LED0-->PB.5 端口配置
 GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP; 		 //推挽输出
 GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;		 //IO口速度为50MHz
 GPIO_Init(GPIOB, &GPIO_InitStructure);					 //根据设定参数初始化GPIOB.5
 GPIO_SetBits(GPIOB,GPIO_Pin_5);						 //PB.5 输出高

 GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;	    		 //LED1-->PE.5 端口配置, 推挽输出
 GPIO_Init(GPIOE, &GPIO_InitStructure);	  				 //推挽输出 ，IO口速度为50MHz
 GPIO_SetBits(GPIOE,GPIO_Pin_5); 						 //PE.5 输出高 
}

//main.c
#include "led.h"
#include "delay.h"
#include "key.h"
#include "sys.h"
#include "usart.h"
#include "timer.h"
/************************************************
 ALIENTEK精英STM32开发板实验8
 定时器中断实验  
************************************************/
	
 int main(void)
 {		
 
	delay_init();	    	 //延时函数初始化	  
	NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); //设置NVIC中断分组2:2位抢占优先级，2位响应优先级
	uart_init(115200);	 //串口初始化为115200
 	LED_Init();			     //LED端口初始化
	TIM3_Int_Init(4999,7199);//10Khz的计数频率，计数到5000为500ms  定时器 
   	while(1)
	{
		LED0=!LED0;
		delay_ms(200);		   
	}	 

 
}