LAN9252/3 EtherCAT module

LAN9252/3 EtherCAT module

LAN9252/3 is a 2/3-port EtherCAT slave controller with 3 Fieldbus Memory Management Units (FMMUs) and 4 SyncManagers

• Interfaces to most 8/16-bit embedded controllers and 32-bit embedded controllers with an 8/16-bit bus

• Integrated Ethernet PHYs with HP Auto-MDIX

• Wake on LAN (WoL) support

• Low power mode allows systems to enter sleep mode until addressed by the Master

• Cable diagnostic support

• 1.8V to 3.3V variable voltage I/O

• Integrated 1.2V regulator for single 3.3V operation

• Low pin count and small body size package

 

TABLE OF CONTENTS

1. Key benefits?
2. Target Applications
3. Pinout diagram
4. Jumpers and settings
5. LEDs and buttons
6. Software support
7. Third party support
8. Downloads

 

 

 

 

key Benefits?

• Integrated high-performance 100Mbps Ethernet transceivers - Compliant with IEEE 802.3/802.3u (Fast Ethernet) - 100BASE-FX support via external fiber transceiver - Loop-back modes - Automatic polarity detection and correction - HP Auto-MDIX

• EtherCAT slave controller - Supports 3 FMMUs - Supports 4 SyncManagers - Distributed clock support allows synchronization with other EtherCAT devices - 4K bytes of DPRAM

• 8/16-Bit Host Bus Interface - Indexed register or multiplexed bus - Allows local host to enter sleep mode until addressed by EtherCAT Master - SPI / Quad SPI support

• Digital I/O Mode for optimized system cost

• 3rd port for flexible network configurations

• Comprehensive power management features - 3 power-down levels - Wake on link status change (energy detect) - Magic packet wakeup, Wake on LAN (WoL), wake on broadcast, wake on perfect DA - Wakeup indicator event signal

• Power and I/O - Integrated power-on reset circuit - Latch-up performance exceeds 150mA per EIA/JESD78, Class II - JEDEC Class 3A ESD performance - Single 3.3V power supply (integrated 1.2V regulator)

• Additional Features - Multifunction GPIOs - Ability to use low cost 25MHz crystal for reduced BOM

• Packaging - Pb-free RoHS compliant 64-pin QFN or 64-pin TQFPEP

• Available in commercial, industrial, and extended industrial* temp. ranges

Target Applications

• Motor Motion Control

• Process/Factory Automation

• Communication Modules, Interface Cards

• Sensors

• Hydraulic & Pneumatic Valve Systems

• Operator Interfaces

 

PINOUT DIAGRAM

This table shows how the pinout on LAN9252/3 Pro.

LAN9253 the details of PIN description, Pls refer Datasheet Page12 LAN9253 datasheet

LAN9252 the details of PIN description, Pls refer Datasheet Page12 LAN9252 datasheet

The LAN9252/3 EtherCAT module PIN description as following:

 

PIN	Notes	PIN	Notes	PIN	Notes
1	GPIO0	2	GPIO1	CS	Chip select
3	GPIO2	4	GPIO3	SCK	SPI Clock
5	GPIO4	6	GPIO5	MISO	SPI data OP
7	GPIO6	8	GPIO7	MOSI	SPI data IP
9	GPIO8	10	GPIO9	IRQ	IRQ
11	GPIO10	12	GPIO11	RST	Reset
13	GPIO12	14	GPIO13	+3.3V	Power supply
15	GPIO14	16	GPIO15	GND	Ground
17	SYNC0	18	SYNC1

 

Chip set

 

 

ADDITIONAL PINS

CHIP MODE SELECTION

 

Jumper settings as following:

 

 

LEDS AND BUTTONS

Designator	Name	Type	Description
D1	D1	INDICATOR	INDICATOR

SOFTWARE SUPPORT

We provide a library for the LAN9252/3 Pro on Microchip page:for LAN9252

 https://www.microchip.com/wwwproducts/en/LAN9252

for LAN9253 https://www.microchip.com/wwwproducts/en/LAN9253

as well as a demo application (example), developed using. The demo can run on all the mainboard.

DOWNLOADS

Pls Press Ctrl+click to enter the link

 

LAN9252 datasheet

LAN9252 all Doc

LAN9252 reference design

LAN9252 Driver

LAN9253 datasheet

LAN925x family Doc

LAN9253 all Doc

LAN9253 reference design

LAN9252 & LAN9253 compare

LAN9253 Driver

Third party support

Driver support:

https://github.com/MicrochipTech/ethercat-software-framework

https://download.csdn.net/download/weixin_41740665/10914039

链接：https://pan.baidu.com/s/1LYyLEkbiOvv2sJ5vqb8MrQ

提取码：89ac