一、实验拓扑
二、实验要求
1、R5为ISP,只能进行IP地址配置,其所有地址均配为公有I地址;
2、R1和Rs间使用PPP的PAP认证,R5为主认证方:
R2与R5之间使用ppp的cHAP认证,R5为主认证方;
R3与R5之间使用HDLC封装;
3、R1、R2、R3构建一个MGRE环境,R1为中心站点,R1、R4间为点到点的GRE;
4、整个私有网络基本RIP全网可达,
5、所有pc设置私有IP为源IP,可以访问R5环回
三.实验步骤
[R1]int g0/0/0
[R1-GigabitEthernet0/0/0]ip add 192.168.1.254 24
[R1-GigabitEthernet0/0/0]int s4/0/0
[R1-Serial4/0/0]ip add 15.1.1.1 24
[R2]int g0/0/0
[R2-GigabitEthernet0/0/0]ip add 192.168.2.254 24
[R2-GigabitEthernet0/0/0]int s4/0/0
[R2-Serial4/0/0]ip add 25.1.1.2 24
[R3]int g0/0/0
[R3-GigabitEthernet0/0/0]ip add 192.168.3.254 24
[R3]int s4/0/0
[R3-Serial4/0/0]ip add 35.1.1.3 24
[R4]int g0/0/0
[R4-GigabitEthernet0/0/0]ip add 45.1.1.4 24
[R4-GigabitEthernet0/0/0]int g0/0/1
[R4-GigabitEthernet0/0/1]ip add 192.168.4.254 24
[R5]int s4/0/1
[R5-Serial4/0/1]ip add 15.1.1.5 24
[R5-Serial4/0/1]int s3/0/1
[R5-Serial3/0/1]ip add 25.1.1.5 24
[R5-Serial3/0/1]int s4/0/0
[R5-Serial4/0/0]ip add 35.1.1.5 24
[R5-Serial4/0/0]int g0/0/0
[R5-GigabitEthernet0/0/0]ip add 45.1.1.5 24
[R5-Serial3/0/1]int l0
[R5-LoopBack0]ip add 5.5.5.5 24
2.做PPP认证
[R5-aaa]local-user lsl password cipher lsl666
[R5-aaa]local-user lsl service-type ppp
[R5-aaa]int s4/0/1
[R5-Serial4/0/1]ppp au
[R5-Serial4/0/1]ppp authentication-mode pap
[R1]int s4/0/0
[R1-Serial4/0/0]ppp pap local-user lsl password cipher lsl666
[R1-Serial4/0/0]shutdown
[R1-Serial4/0/0]undo shutdown
[R3]int s4/0/0
[R3-Serial4/0/0]link-protocol hdic
[R5]int s4/0/0
[R5-Serial4/0/0]link-protocol hdlc
[R1]ip route-static 0.0.0.0 0 15.1.1.5
[R2]ip route-static 0.0.0.0 0 25.1.1.5
[R3]ip route-static 0.0.0.0 0 35.1.1.5
[R4]ip route-static 0.0.0.0 0 45.1.1.5
[R1]ip route-static 0.0.0.0 0 15.1.1.5
[R1]int Tunnel 0/0/0
[R1-Tunnel0/0/0]ip add 10.1.1.1 24
[R1-Tunnel0/0/0]tunnel-protocol gre p2mp
[R1-Tunnel0/0/0]source 15.1.1.1
[R1-Tunnel0/0/0]NHRP network-id 100
[R2]int Tunnel 0/0/0
[R2-Tunnel0/0/0]ip add 10.1.1.2 24
[R2-Tunnel0/0/0]tunnel-protocol gre p2mp
[R2-Tunnel0/0/0]source Serial 4/0/0
[R2-Tunnel0/0/0]nhrp entry 10.1.1.1 15.1.1.1 register
[R3]int Tunnel 0/0/0
[R3-Tunnel0/0/0]ip add 10.1.1.3 24
[R3-Tunnel0/0/0]tunnel-protocol gre p2mp
[R3-Tunnel0/0/0]source Serial 4/0/0
[R3-Tunnel0/0/0]nhrp entry 10.1.1.1 15.1.1.1 register
配置GRE
[R1]int Tunnel 0/0/1
[R1-Tunnel0/0/1]ip add 10.1.2.1 24
[R1-Tunnel0/0/1]tunnel-protocol gre
[R1-Tunnel0/0/1]source 15.1.1.1
[R1-Tunnel0/0/1]destination 45.1.1.4
[R4]int Tunnel 0/0/1
[R4-Tunnel0/0/1]ip add 10.1.2.4 24
[R4-Tunnel0/0/1]tunnel-protocol gre
[R4-Tunnel0/0/1]source 45.1.1.4
[R4-Tunnel0/0/1]description 15.1.1.1
配置RIP协议
[R1]rip 1
[R1-rip-1]v 2
[R1-rip-1]undo summary
[R1-rip-1]net 192.168.1.0
[R1-rip-1]net 10.0.0.0
[R2]rip 1
[R2-rip-1]v 2
[R2-rip-1]undo summary
[R2-rip-1]net 192.168.2.0
[R2-rip-1]net 10.0.0.0
[R3]rip 1
[R3-rip-1]v 2
[R3-rip-1]undo summary
[R3-rip-1]net 192.168.3.0
[R3-rip-1]net 10.0.0.0
[R4]rip 1
[R4-rip-1]v 2
[R4-rip-1]undo summary
[R4-rip-1]net 192.168.4.0
[R4-rip-1]net 10.0.0.0
开启伪广播
[R1]int Tunnel 0/0/0
[R1-Tunnel0/0/0]nhrp entry multicast dynamic
[R1-Tunnel0/0/0]undo rip split-horizon
[R2]int Tunnel 0/0/0
[R2-Tunnel0/0/0]undo rip split-horizon
[R3]int Tunnel 0/0/0
[R3-Tunnel0/0/0]undo rip split-horizon
配置nat
[R1]acl 2000
[R1-acl-basic-2000]rule permit source 192.168.1.0 0.0.0.255
[R1]int s4/0/0
[R1-Serial4/0/0]nat outbound 2000
[R2]acl 2000
[R2-acl-basic-2000]rule permit source 192.168.1.0 0.0.0.255
[R2]int s4/0/0
[R2-Serial4/0/0]nat outbound 2000
[R3]acl 2000
[R3-acl-basic-2000]rule permit source 192.168.1.0 0.0.0.255
[R3]int s4/0/0
[R3-Serial4/0/0]nat outbound 2000
[R4]acl 2000
[R4-acl-basic-2000]rule permit source 192.168.1.0 0.0.0.255
[R4]int g0/0/0
[R4-GigabitEthernet0/0/0]nat outb
[R4]int g0/0/0
[R4-GigabitEthernet0/0/0]nat outbound 2000
四.测试图