Tools and Utilities for Booting

最新推荐文章于 2022-12-08 13:46:24 发布

ztguang

最新推荐文章于 2022-12-08 13:46:24 发布

阅读量298

点赞数

分类专栏：嵌入式/移动IoT/雾计算

本文链接：https://blog.csdn.net/ztguang/article/details/51011324

版权

嵌入式/移动IoT/雾计算专栏收录该内容

242 篇文章 3 订阅

订阅专栏

http://blog.21ic.com/user1/1066/archives/2006/8248.html

JTAG and Jflash-linux

Uploading can be achieved via the JTAG port using software such a Jflash and Jflash-linux. Usage for Windows or GNU/Linux host is essentially identical. The examples given here use GNU/Linux syntax.

In order to use the JTAG programmer, you need to connect the parallel port of your computer to the JTAG port of the device you want to program. The details of this vary from device to device - see the relevant install chapter. Ensure the device is powered up. Jflash and Jflash-linux both autosense for available parallel ports so it shouldn't matter where you plug it in.

You can then issue the following command as root:

./Jflash-linux blob-1.0.7b

and you should see something like the following (this example is using the blob-1.08-pre2 binary on the CD on a LART). After uploading the device will reset itself before running Blob.

using printer port at 378
Seems to be a pair of 28F160F3, bottom boot. Good. 

Starting erase for    c8e bytes
Erasing block   0   
Erasing done                                           
Starting programming
Writing flash at hex address      1b0, 13.44% done    
Writing flash at hex address      3d0, 30.37% done    
Writing flash at hex address      5f0, 47.29% done    
Writing flash at hex address      810, 64.22% done    
Writing flash at hex address      a30, 81.14% done 
Writing flash at hex address      c50, 98.07% done 
Programming done                                            
Starting verify
Verifying flash at hex address      643, 49.88% done    
Verification successful!

Note: If something is wrong you will see error messages like the following:

error, failed to read device ID
ACT: 0000 0000000000000000 00000000000 0
EXP: X001 0001000010000100 00000110101 1

failed to read device ID for the SA-1100

error, failed to read device ID
ACT: 1111 1111111111111111 11111111111 1
EXP: X001 0001000010000100 00000110101 1

failed to read device ID for the SA-1100

error, failed to read device ID
ACT: 1001 1010000111001011 01011000111 1
EXP: X001 0001000010000100 00000110101 1

failed to read device ID for the SA-1100

There are a number of possible causes. If you get all 1's then you maybe using the wrong parallel port, or the cable or dongle is not plugged in, or the device is not powered up. If you get all zeros then you may be using the wrong version of JFlash-linux, or (on a LART) you may be suffering from the 'JTAG reset problem', see the section called LART JTAG reset problem in Chapter 3. If you get random numbers some of the time and zeros the rest of the time then you are almost certainly using the wrong version of JFlash-linux.

阅读(791) | 评论(0) | 转发(0) |

上一篇：Linux有用命令及配置汇总

下一篇：CentOS 5.3 挂载读写 ntfs硬盘