HCIP-BPG实验（3）

一、实验目的

1.全网可达
2.isp只能配置ip地址

二、具体配置

先使ipv4能够访问运营商

在r2上配置nat

[r2]acl 2000

[r2-acl-basic-2000]rule permit source any

[r2]int g0/0/2

[r2-GigabitEthernet0/0/2]nat outbound 2000

二、划分6to4 tunnel地址

 将r2g0/0/2接口ipv4地址转换为6to4 tunnel地址2002:1d01:0102::/48划分给下方的路由器

配置ipv6地址（）

[r1]ipv6

[r1]interface g0/0/0

[r1-GigabitEthernet0/0/0]ipv6 enable

[r1-GigabitEthernet0/0/0]ipv6 address 2002:1d01:0102:1::1 64

[r1-GigabitEthernet0/0/0]int l0

[r1-LoopBack0]ipv6 enable

[r1-LoopBack0]ipv6 address 2002:1d01:0102:11::1 64

[r1-LoopBack0]display ipv6 interface brief

*down: administratively down

(l): loopback

(s): spoofing

Interface Physical Protocol

GigabitEthernet0/0/0 up up

[IPv6 Address] 2002:1D01:102:1::1

LoopBack0 up up(s)

[IPv6 Address] 2002:1D01:102:11::1

[r1-LoopBack0]

三、配置ripng

[r10]ripng 1

[r10-ripng-1]int g0/0/1

[r10-GigabitEthernet0/0/1]ripng 1 enable

[r10-GigabitEthernet0/0/1]q

[r10]int l0

[r10-LoopBack0]ripng 1 enable

[r10-LoopBack0]q

[r10]interfa Tunnel 0/0/0

[r10-Tunnel0/0/0]ripng 1 enable

[r10-Tunnel0/0/0]q

四、配置6to4 tunnel隧道 

在r2-r10上配置隧道

[r2-Tunnel0/0/0]display this

[V200R003C00]

#

interface Tunnel0/0/0

ipv6 enable

ipv6 address 2002:1D01:102:3::2/64

tunnel-protocol ipv6-ipv4 6to4

source GigabitEthernet0/0/2

#

return

[r2-Tunnel0/0/0]

  r1  ping  r11

  

五、启用ospfv3

在ospf区域启用ospfv3 100，例r6

[r6]ospfv3 100

[r6-ospfv3-100]router-id 6.6.6.6

[r6]int g0/0/0

[r6-GigabitEthernet0/0/0]ospfv3 100 area 0

[r6-GigabitEthernet0/0/1]int l0

[r6-LoopBack0]ospfv3 100 area 0

 六、配置bgp

[r3]bgp 64511

[r3-bgp]router-id 3.3.3.3

[r3-bgp]confederation id 100

[r3-bgp]peer 4::4 as-number 64511

[r3-bgp]peer 4::4 connect-interface l0

[r3-bgp]ipv6-family

[r3-bgp-af-ipv6]peer 4::4 enable

[r3-bgp-af-ipv6]peer 4::4 next-hop-local

[r5-bgp]display this

[V200R003C00]

#

bgp 64511

router-id 5.5.5.5

confederation id 100

confederation peer-as 64512

peer 4::4 as-number 64511

peer 4::4 connect-interface LoopBack0

peer 6::6 as-number 64512

peer 6::6 ebgp-max-hop 2

peer 6::6 connect-interface LoopBack0

#

ipv4-family unicast

undo synchronization

#

ipv6-family unicast

undo synchronization

peer 4::4 enable

peer 6::6 enable

#

return

 七、bgp导入路由

在r7上导入ripng 2

[r7-bgp-af-ipv6]import-route ripng 2

在r6上导入ospfv3 100 

[r6-bgp-af-ipv6]import-route ospfv3 100

  

八、配置缺省

在r3的ospfv3 100 中下放缺省指向r2， r7、r8下放缺省指向r6