【嵌入式系统实践】实验四综合实验部分代码

由于综合实验未给出一个固定的思路或者目标，这里仅写出部分内容，以便于期末复习背诵手写代码用。

 自己写的func.h和func.c涵盖了期末所考手写代码部分，背诵过来就挂不了科。

// functions.h
#ifndef FUNCTIONS_H
#define FUNCTIONS_H

extern int choice;

extern int hour, minute, second;
void USART_Config(void);
void GPIO_SETTING(void);		//LED Setting
void NVIC_config(void);
void TIM3_config(void);
void NVIC_Conf(void);
void KEY_Conf(void);				//pc5 key0
void EXTI_conf(void);
void Set485Direction(void);

#endif

#include "func.h"
#include "STM32F10X.h"

int choice = 0;


void USART_Config(void)
{
	GPIO_InitTypeDef GPIO_InitStructure;
	USART_InitTypeDef  USART_InitStructure;
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA|RCC_APB2Periph_USART1, ENABLE);

	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;    	//PA9,TX
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; 
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
	GPIO_Init(GPIOA,&GPIO_InitStructure);
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;  	//PA10,RX
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
	GPIO_Init(GPIOA, &GPIO_InitStructure);

	USART_InitStructure.USART_BaudRate = 9600;  
	USART_InitStructure.USART_WordLength = USART_WordLength_8b; 
	USART_InitStructure.USART_StopBits = USART_StopBits_1; 
	USART_InitStructure.USART_Parity = USART_Parity_No; 
	USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;           
	USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;    
	USART_Cmd(USART1, ENABLE);     
	USART_Init(USART1, &USART_InitStructure);  
}

 void GPIO_SETTING(void)		//LED Setting
{
	GPIO_InitTypeDef gpio_init;
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB | RCC_APB2Periph_AFIO, ENABLE);
	GPIO_PinRemapConfig(GPIO_Remap_SWJ_JTAGDisable, ENABLE);
	gpio_init.GPIO_Pin = GPIO_Pin_4 | GPIO_Pin_5 | GPIO_Pin_6 | GPIO_Pin_7;
	gpio_init.GPIO_Mode = GPIO_Mode_Out_PP; 
	gpio_init.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_Init(GPIOB,&gpio_init);
}
 
void NVIC_config(void){
	NVIC_InitTypeDef NvicInit;
	NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);
	NvicInit.NVIC_IRQChannel = TIM3_IRQn;
	NvicInit.NVIC_IRQChannelPreemptionPriority = 0;
	NvicInit.NVIC_IRQChannelSubPriority = 0;
	NvicInit.NVIC_IRQChannelCmd = ENABLE;
	NVIC_Init(&NvicInit);
}

void TIM3_config(void){
	TIM_TimeBaseInitTypeDef TIM_Time_Struct;
	RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE);
	TIM_Time_Struct.TIM_Prescaler = 7199;
	TIM_Time_Struct.TIM_Period = 9999;
	TIM_Time_Struct.TIM_CounterMode = TIM_CounterMode_Up;
	TIM_TimeBaseInit(TIM3, &TIM_Time_Struct);
	TIM_ITConfig(TIM3, TIM_IT_Update, ENABLE);
	TIM_Cmd(TIM3, ENABLE);
}

void KEY_Conf(void){			//pc5 key0
	GPIO_InitTypeDef key;
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC | RCC_APB2Periph_AFIO, ENABLE);
	key.GPIO_Pin = GPIO_Pin_5;
	key.GPIO_Mode = GPIO_Mode_IPU;
	GPIO_Init(GPIOC, &key);
	GPIO_EXTILineConfig(GPIO_PortSourceGPIOC, GPIO_PinSource5);
}
 
void EXTI_conf(void){
	EXTI_InitTypeDef exti;
	exti.EXTI_Line = EXTI_Line5;
	exti.EXTI_Mode = EXTI_Mode_Interrupt;
	exti.EXTI_Trigger = EXTI_Trigger_Falling;
	EXTI_Init(&exti);
}

void Set485Direction(void)
{
    GPIO_InitTypeDef GPIO_InitStructure;
    RCC_APB1PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE);

    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1;
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
    GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
    GPIO_Init(GPIOB, &GPIO_InitStructure);

    GPIO_SetBits(GPIOA, GPIO_Pin_1); 

}

其余内容可自己DIY，这里不再给出。