uboot中查看板子信息的命令bdinfo

# bdinfo 
arch_number = 0x000000000000xfxx
boot_params = 0x0000000040000100      //启动参数保存开始地址 
DRAM bank   = 0x0000000000000000
-> start    = 0x0000000040000000      //DRAM的开始地址
-> size     = 0x0000000020000000      //DRAM的大小
eth0name    = gmac0
ethaddr     = 00:xx:x:x:xx:xx
current eth = gmac0
ip_addr     = xx.xx.xx.xx
baudrate    = 115200 bps        //波特率
TLB addr    = 0x000000005fff0000
relocaddr   = 0x000000005ff16000
reloc off   = 0x0000000017716000
irq_sp      = 0x000000005fe75de0
sp start    = 0x000000005fe75de0
Early malloc usage: d0 / 2000

得到板子上DRAM的开始地址和大小和启动参数保存开始地址和波特率

include/asm-generic/u-boot.h

typedef struct bd_info {
	unsigned long	bi_memstart;	/* start of DRAM memory */
	phys_size_t	bi_memsize;	/* size	 of DRAM memory in bytes */
	unsigned long	bi_flashstart;	/* start of FLASH memory */
	unsigned long	bi_flashsize;	/* size	 of FLASH memory */
	unsigned long	bi_flashoffset; /* reserved area for startup monitor */
	unsigned long	bi_sramstart;	/* start of SRAM memory */
	unsigned long	bi_sramsize;	/* size	 of SRAM memory */
#ifdef CONFIG_ARM
	unsigned long	bi_arm_freq; /* arm frequency */
	unsigned long	bi_dsp_freq; /* dsp core frequency */
	unsigned long	bi_ddr_freq; /* ddr frequency */
#endif
#if defined(CONFIG_MPC8xx) || defined(CONFIG_E500) || defined(CONFIG_MPC86xx)
	unsigned long	bi_immr_base;	/* base of IMMR register */
#endif
#if defined(CONFIG_M68K)
	unsigned long	bi_mbar_base;	/* base of internal registers */
#endif
#if defined(CONFIG_MPC83xx)
	unsigned long	bi_immrbar;
#endif
	unsigned long	bi_bootflags;	/* boot / reboot flag (Unused) */
	unsigned long	bi_ip_addr;	/* IP Address */
	unsigned char	bi_enetaddr[6];	/* OLD: see README.enetaddr */
	unsigned short	bi_ethspeed;	/* Ethernet speed in Mbps */
	unsigned long	bi_intfreq;	/* Internal Freq, in MHz */
	unsigned long	bi_busfreq;	/* Bus Freq, in MHz */
#if defined(CONFIG_CPM2)
	unsigned long	bi_cpmfreq;	/* CPM_CLK Freq, in MHz */
	unsigned long	bi_brgfreq;	/* BRG_CLK Freq, in MHz */
	unsigned long	bi_sccfreq;	/* SCC_CLK Freq, in MHz */
	unsigned long	bi_vco;		/* VCO Out from PLL, in MHz */
#endif
#if defined(CONFIG_M68K)
	unsigned long	bi_ipbfreq;	/* IPB Bus Freq, in MHz */
	unsigned long	bi_pcifreq;	/* PCI Bus Freq, in MHz */
#endif
#if defined(CONFIG_EXTRA_CLOCK)
	unsigned long bi_inpfreq;	/* input Freq in MHz */
	unsigned long bi_vcofreq;	/* vco Freq in MHz */
	unsigned long bi_flbfreq;	/* Flexbus Freq in MHz */
#endif

#ifdef CONFIG_HAS_ETH1
	unsigned char   bi_enet1addr[6];	/* OLD: see README.enetaddr */
#endif
#ifdef CONFIG_HAS_ETH2
	unsigned char	bi_enet2addr[6];	/* OLD: see README.enetaddr */
#endif
#ifdef CONFIG_HAS_ETH3
	unsigned char   bi_enet3addr[6];	/* OLD: see README.enetaddr */
#endif
#ifdef CONFIG_HAS_ETH4
	unsigned char   bi_enet4addr[6];	/* OLD: see README.enetaddr */
#endif
#ifdef CONFIG_HAS_ETH5
	unsigned char   bi_enet5addr[6];	/* OLD: see README.enetaddr */
#endif

	ulong	        bi_arch_number;	/* unique id for this board */
	ulong	        bi_boot_params;	/* where this board expects params */
#ifdef CONFIG_NR_DRAM_BANKS
	struct {			/* RAM configuration */
		phys_addr_t start;
		phys_size_t size;
	} bi_dram[CONFIG_NR_DRAM_BANKS];
#endif /* CONFIG_NR_DRAM_BANKS */
} bd_t;