RK356X 如何配置PMU

一：RK809的了解

无论是RK3568,还是PX30亦或是RK3588对于电源的配置都使用到了RK809芯片做电源管理，并且在RK809中也做了休眠，关机，耳机，喇叭，等等功能。本章对于电源域的配置做了详解如下：

二：设备树配置：

当我们拿到RK的源码后，在官方的dts中可以找到在I2C0节点下有RK809的配置（通过电路图可以看到RK809挂载在I2C0中）,找到RK809后可以看到如下配置：

红框中对休眠，关机等等做了说明，可以在pinctrl中，找到对应的说明：

我们继续往下看：

vdda0v9_image: LDO_REG1 {
                regulator-boot-on;
                regulator-always-on;
                regulator-min-microvolt = <900000>;
                regulator-max-microvolt = <900000>;
                regulator-name = "vdda0v9_image";
                regulator-state-mem {
                    regulator-off-in-suspend;
                };
            };

            vdda_0v9: LDO_REG2 {
                regulator-always-on;
                regulator-boot-on;
                regulator-min-microvolt = <900000>;
                regulator-max-microvolt = <900000>;
                regulator-name = "vdda_0v9";
                regulator-state-mem {
                    regulator-off-in-suspend;
                };
            };

            vdda0v9_pmu: LDO_REG3 {
                regulator-always-on;
                regulator-boot-on;
                regulator-min-microvolt = <900000>;
                regulator-max-microvolt = <900000>;
                regulator-name = "vdda0v9_pmu";
                regulator-state-mem {
                    regulator-on-in-suspend;
                    regulator-suspend-microvolt = <900000>;
                };
            };

            vccio_acodec: LDO_REG4 {
                regulator-always-on;
                regulator-boot-on;
                regulator-min-microvolt = <3300000>;
                regulator-max-microvolt = <3300000>;
                regulator-name = "vccio_acodec";
                regulator-state-mem {
                    regulator-off-in-suspend;
                };
            };

            vccio_sd: LDO_REG5 {
                regulator-always-on;
                regulator-boot-on;
                regulator-min-microvolt = <1800000>;
                regulator-max-microvolt = <3300000>;
                regulator-name = "vccio_sd";
                regulator-state-mem {
                    regulator-off-in-suspend;
                };
            };

            vcc3v3_pmu: LDO_REG6 {
                regulator-always-on;
                regulator-boot-on;
                regulator-min-microvolt = <3300000>;
                regulator-max-microvolt = <3300000>;
                regulator-name = "vcc3v3_pmu";
                regulator-state-mem {
                    regulator-on-in-suspend;
                    regulator-suspend-microvolt = <3300000>;
                };
            };

            vcca_1v8: LDO_REG7 {
                regulator-always-on;
                regulator-boot-on;
                regulator-min-microvolt = <1800000>;
                regulator-max-microvolt = <1800000>;
                regulator-name = "vcca_1v8";
                regulator-state-mem {
                    regulator-off-in-suspend;
                };
            };

            vcca1v8_pmu: LDO_REG8 {
                regulator-always-on;
                regulator-boot-on;
                regulator-min-microvolt = <1800000>;
                regulator-max-microvolt = <1800000>;
                regulator-name = "vcca1v8_pmu";
                regulator-state-mem {
                    regulator-on-in-suspend;
                    regulator-suspend-microvolt = <1800000>;
                };
            };

            vcca1v8_image: LDO_REG9 {
                regulator-always-on;
                regulator-boot-on;
                regulator-min-microvolt = <1800000>;
                regulator-max-microvolt = <1800000>;
                regulator-name = "vcca1v8_image";
                regulator-state-mem {
                    regulator-off-in-suspend;
                };
            };

            vcc_1v8: DCDC_REG5 {
                regulator-always-on;
                regulator-boot-on;
                regulator-min-microvolt = <1800000>;
                regulator-max-microvolt = <1800000>;
                regulator-name = "vcc_1v8";
                regulator-state-mem {
                    regulator-off-in-suspend;
                };
            };

            vcc_3v3: SWITCH_REG1 {
                regulator-always-on;
                regulator-boot-on;
                regulator-name = "vcc_3v3";
                regulator-state-mem {
                    regulator-off-in-suspend;
                };
            };

            vcc3v3_sd: SWITCH_REG2 {
                regulator-always-on;
                regulator-boot-on;
                regulator-name = "vcc3v3_sd";
                regulator-state-mem {
                    regulator-off-in-suspend;
                };
            };
        };

以上的设备树配置主要看核心板中对于RK809的电路，如下：

将其中的每个引脚电压进行对应。

最后也是最重要的一步：（对pmu_io进行配置）

可以看在pmu上面的解释，发现vccio2不需要配置

同样配置也是需要在电路图中找到对应的电压如下图：

vdd_logic: DCDC_REG1 {
                regulator-always-on;
                regulator-boot-on;
                regulator-min-microvolt = <500000>;
                regulator-max-microvolt = <1350000>;
                regulator-init-microvolt = <900000>;
                regulator-ramp-delay = <6001>;
                regulator-initial-mode = <0x2>;
                regulator-name = "vdd_logic";
                regulator-state-mem {
                    regulator-off-in-suspend;
                };
            };

            vdd_gpu: DCDC_REG2 {
                regulator-always-on;
                regulator-boot-on;
                regulator-min-microvolt = <500000>;
                regulator-max-microvolt = <1350000>;
                regulator-init-microvolt = <900000>;
                regulator-ramp-delay = <6001>;
                regulator-initial-mode = <0x2>;
                regulator-name = "vdd_gpu";
                regulator-state-mem {
                    regulator-off-in-suspend;
                };
            };

            vcc_ddr: DCDC_REG3 {
                regulator-always-on;
                regulator-boot-on;
                regulator-initial-mode = <0x2>;
                regulator-name = "vcc_ddr";
                regulator-state-mem {
                    regulator-on-in-suspend;
                };
            };

            vdd_npu: DCDC_REG4 {
                regulator-always-on;
                regulator-boot-on;
                regulator-min-microvolt = <500000>;
                regulator-max-microvolt = <1350000>;
                regulator-init-microvolt = <900000>;
                regulator-ramp-delay = <6001>;
                regulator-initial-mode = <0x2>;
                regulator-name = "vdd_npu";
                regulator-state-mem {
                    regulator-off-in-suspend;
                };
            };

三：最后一步：

将rk其他的外设功能全部关闭，（自己不知道是什么功能的节点可以百度），关闭所有外设之后，编译：将程序烧录到板卡中。

注意：hdmi需要打开，