stm32f042调试Can心得

最新推荐文章于 2024-09-21 07:04:21 发布

armwind

最新推荐文章于 2024-09-21 07:04:21 发布

阅读量4.1k

点赞数 5

分类专栏： Can Bus

本文链接：https://blog.csdn.net/armwind/article/details/106931881

版权

Can Bus 专栏收录该内容

4 篇文章 3 订阅

订阅专栏

这两天玩了一下stm32f042的can，但是折腾了2个晚上，还是没有进展。我知道stm32f042F6P6 ssop20封装的pin17,pin18默认是PA9,PA10的功能，如果想使用PA11和PA12，需要进行端口映射。这样的话，我直接就用了下面的代码，进行端口映射，

 SYSCFG_MemoryRemapConfig(SYSCFG_CFGR1_PA11_PA12_RMP);

结果Can总线一直没有波形出来。使用回环模式调试，总线上一直没有波形。

由于CAN的PA11和PA12和串口1的PA9和PA10是复用的，没有第一时间使用串口进行调试。今天晚上下班将usart2飞线飞出来了。使能断言后，发现下面的断言错误。

DEBUG [D] main:94 hello armwind
DEBUG [D] assert_failed:94 …/Lib/STM32F0xx_StdPeriph_Driver/src/stm32f0xx_syscfg.c,line:119

查看源码发现，断言表明，这个方法只能映射系统mem.

void SYSCFG_MemoryRemapConfig(uint32_t SYSCFG_MemoryRemap)
{
  uint32_t tmpctrl = 0;

  /* Check the parameter */
  assert_param(IS_SYSCFG_MEMORY_REMAP(SYSCFG_MemoryRemap));

  /* Get CFGR1 register value */
  tmpctrl = SYSCFG->CFGR1;

  /* Clear MEM_MODE bits */
  tmpctrl &= (uint32_t) (~SYSCFG_CFGR1_MEM_MODE);

  /* Set the new MEM_MODE bits value */
  tmpctrl |= (uint32_t) SYSCFG_MemoryRemap;

  /* Set CFGR1 register with the new memory remap configuration */
  SYSCFG->CFGR1 = tmpctrl;
}

//宏定义很明显
#define IS_SYSCFG_MEMORY_REMAP(REMAP) (((REMAP) == SYSCFG_MemoryRemap_Flash) || \
                                       ((REMAP) == SYSCFG_MemoryRemap_SystemMemory) || \
                                       ((REMAP) == SYSCFG_MemoryRemap_SRAM))

所以使用下面代码即可map成功

//不要覆盖掉系统原始的配置
SYSCFG->CFGR1 = SYSCFG->CFGR1 | SYSCFG_CFGR1_PA11_PA12_RMP;

完整的Can初始化代码

void can_init(void)
{
  GPIO_InitTypeDef  GPIO_InitStructure;
  NVIC_InitTypeDef  NVIC_InitStructure;
  CAN_InitTypeDef        CAN_InitStructure;
  CAN_FilterInitTypeDef  CAN_FilterInitStructure;

  RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
  SYSCFG->CFGR1 = SYSCFG->CFGR1 | SYSCFG_CFGR1_PA11_PA12_RMP;

  //这里一定要先映射GPIO
  /* Enable GPIO clock */
  RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, ENABLE);
  /* Connect CAN pins to AF7 */
  /* CAN GPIOs configuration **************************************************/
  GPIO_PinAFConfig(GPIOA, GPIO_PinSource11, GPIO_AF_4);
  GPIO_PinAFConfig(GPIOA, GPIO_PinSource12, GPIO_AF_4);

  /* Configure CAN RX and TX pins */
  GPIO_InitStructure.GPIO_Pin = GPIO_PinSource11 | GPIO_PinSource12;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
  GPIO_InitStructure.GPIO_PuPd  = GPIO_PuPd_UP;
  GPIO_Init(GPIOA, &GPIO_InitStructure);

  /* NVIC configuration *******************************************************/
  NVIC_InitStructure.NVIC_IRQChannel = CEC_CAN_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPriority = 0x0;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);

  /* CAN configuration ********************************************************/
  /* Enable CAN clock */
  RCC_APB1PeriphClockCmd(RCC_APB1Periph_CAN, ENABLE);

  /* CAN register init */
  CAN_DeInit(CAN);
  CAN_StructInit(&CAN_InitStructure);

  /* CAN cell init */
  CAN_InitStructure.CAN_TTCM = DISABLE;
  CAN_InitStructure.CAN_ABOM = DISABLE;
  CAN_InitStructure.CAN_AWUM = DISABLE;
  CAN_InitStructure.CAN_NART = DISABLE;
  CAN_InitStructure.CAN_RFLM = DISABLE;
  CAN_InitStructure.CAN_TXFP = DISABLE;
  CAN_InitStructure.CAN_Mode = CAN_Mode_Normal;
  //CAN_InitStructure.CAN_Mode = CAN_Mode_LoopBack;
  CAN_InitStructure.CAN_SJW = CAN_SJW_1tq;

  //200k的配置
  //48M/12/(CAN_SJW_1tq + CAN_BS1_4tq+CAN_BS2_5tq) == 200k
  /* CAN Baudrate = 1MBps (CAN clocked at 36 MHz) */
  CAN_InitStructure.CAN_BS1 = CAN_BS1_4tq;
  CAN_InitStructure.CAN_BS2 = CAN_BS2_5tq;
  CAN_InitStructure.CAN_Prescaler = 12;
  CAN_Init(CAN, &CAN_InitStructure);

  /* CAN filter init */
  CAN_FilterInitStructure.CAN_FilterNumber = 1;
  CAN_FilterInitStructure.CAN_FilterMode = CAN_FilterMode_IdMask;
  CAN_FilterInitStructure.CAN_FilterScale = CAN_FilterScale_32bit;
  CAN_FilterInitStructure.CAN_FilterIdHigh = 0x0000;
  CAN_FilterInitStructure.CAN_FilterIdLow = 0x0000;
  CAN_FilterInitStructure.CAN_FilterMaskIdHigh = 0x0000;
  CAN_FilterInitStructure.CAN_FilterMaskIdLow = 0x0000;
  CAN_FilterInitStructure.CAN_FilterFIFOAssignment = 0;
  CAN_FilterInitStructure.CAN_FilterActivation = ENABLE;
  CAN_FilterInit(&CAN_FilterInitStructure);
  /* Transmit Structure preparation */

  /* Enable FIFO 0 message pending Interrupt */
  CAN_ITConfig(CAN, CAN_IT_FMP0, ENABLE);
}