openwrt_4M_flash启动log

最新推荐文章于 2022-07-17 08:30:43 发布

shareinfo2018

最新推荐文章于 2022-07-17 08:30:43 发布

阅读量1.6k

点赞数

分类专栏： openWrt 文章标签： openwrt_4M_flash启动lo

本文链接：https://blog.csdn.net/chenyefei/article/details/48522801

版权

openWrt 专栏收录该内容

10 篇文章 0 订阅

订阅专栏

U-Boot 1.1.3 (Aug 11 2011 - 14:34:31)

Board: Ralink APSoC DRAM: 32 MB

relocate_code Pointer at: 81fb4000

******************************

Software System Reset Occurred

******************************

spi_wait_nsec: 42

spi device id: c2 20 16 c2 20 (2016c220)

find flash: MX25L3205D

raspi_read: from:30000 len:1000

.raspi_read: from:30000 len:1000

.============================================

Ralink UBoot Version: 3.5.2.0

--------------------------------------------

ASIC 5350_MP (Port5<->None)

DRAM_CONF_FROM: Boot-Strapping

DRAM_TYPE: SDRAM

DRAM_SIZE: 256 Mbits

DRAM_WIDTH: 16 bits

DRAM_TOTAL_WIDTH: 16 bits

TOTAL_MEMORY_SIZE: 32 MBytes

Flash component: SPI Flash

Date:Aug 11 2011 Time:14:34:31

============================================

icache: sets:256, ways:4, linesz:32 ,total:32768

dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 360 MHZ ####

estimate memory size =32 Mbytes

Please choose the operation:

1: Load system code to SDRAM via TFTP.

2: Load system code then write to Flash via TFTP.

3: Boot system code via Flash (default).

4: Entr boot command line interface.

7: Load Boot Loader code then write to Flash via Serial.

9: Load Boot Loader code then write to Flash via TFTP.

You choosed 2

raspi_read: from:40028 len:6

2: System Load Linux Kernel then write to Flash via TFTP.

Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)

Please Input new ones /or Ctrl-C to discard

Input device IP (192.168.1.128) ==:192.168.1.128

Input server IP (192.168.1.118) ==:192.168.1.118

Input Linux Kernel filename (openwrt-ramips-rt305x-mpr-a2-squashfs-sysupgrade.bin) ==:openwrt2

netboot_common, argc= 3

NetTxPacket = 0x81FE59C0

KSEG1ADDR(NetTxPacket) = 0xA1FE59C0

NetLoop,call eth_halt !

NetLoop,call eth_init !

Trying Eth0 (10/100-M)

Waitting for RX_DMA_BUSY status Start... done

Header Payload scatter function is Disable !!

ETH_STATE_ACTIVE!!

Using Eth0 (10/100-M) device

TFTP from server 192.168.1.118; our IP address is 192.168.1.128

Filename 'openwrt2'.

TIMEOUT_COUNT=10,Load address: 0x80100000

Loading: *

ArpTimeoutCheck

T T T T Got ARP REPLY, set server/gtwy eth addr (54:a0:50:53:72:1b)

Got it

Got ARP REQUEST, return our IP

#################################################################

done

Bytes transferred = 3670020 (380004 hex)

NetBootFileXferSize= 00380004

raspi_erase_write: offs:50000, count:380004

raspi_erase: offs:50000 len:380000

........................................................

raspi_write: to:50000 len:380000

........................................................

raspi_read: from:50000 len:10000

.raspi_read: from:60000 len:10000

.raspi_read: from:70000 len:10000

.raspi_read: from:80000 len:10000

.raspi_read: from:90000 len:10000

.raspi_read: from:a0000 len:10000

.raspi_read: from:b0000 len:10000

.raspi_read: from:c0000 len:10000

.raspi_read: from:d0000 len:10000

.raspi_read: from:e0000 len:10000

.raspi_read: from:f0000 len:10000

.raspi_read: from:100000 len:10000

.raspi_read: from:110000 len:10000

.raspi_read: from:120000 len:10000

.raspi_read: from:130000 len:10000

.raspi_read: from:140000 len:10000

.raspi_read: from:150000 len:10000

.raspi_read: from:160000 len:10000

.raspi_read: from:170000 len:10000

.raspi_read: from:180000 len:10000

.raspi_read: from:190000 len:10000

.raspi_read: from:1a0000 len:10000

.raspi_read: from:1b0000 len:10000

.raspi_read: from:1c0000 len:10000

.raspi_read: from:1d0000 len:10000

.raspi_read: from:1e0000 len:10000

.raspi_read: from:1f0000 len:10000

.raspi_read: from:200000 len:10000

.raspi_read: from:210000 len:10000

.raspi_read: from:220000 len:10000

.raspi_read: from:230000 len:10000

.raspi_read: from:240000 len:10000

.raspi_read: from:250000 len:10000

.raspi_read: from:260000 len:10000

.raspi_read: from:270000 len:10000

.raspi_read: from:280000 len:10000

.raspi_read: from:290000 len:10000

.raspi_read: from:2a0000 len:10000

.raspi_read: from:2b0000 len:10000

.raspi_read: from:2c0000 len:10000

.raspi_read: from:2d0000 len:10000

.raspi_read: from:2e0000 len:10000

.raspi_read: from:2f0000 len:10000

.raspi_read: from:300000 len:10000

.raspi_read: from:310000 len:10000

.raspi_read: from:320000 len:10000

.raspi_read: from:330000 len:10000

.raspi_read: from:340000 len:10000

.raspi_read: from:350000 len:10000

.raspi_read: from:360000 len:10000

.raspi_read: from:370000 len:10000

.raspi_read: from:380000 len:10000

.raspi_read: from:390000 len:10000

.raspi_read: from:3a0000 len:10000

.raspi_read: from:3b0000 len:10000

.raspi_read: from:3c0000 len:10000

.raspi_read: from:3d0000 len:10000

.raspi_erase: offs:3d0000 len:10000

raspi_write: to:3d0000 len:10000

raspi_read: from:3d0000 len:10000

.Done!

## Booting image at bc050000 ...

raspi_read: from:50000 len:40

. Image Name: Linux Kernel Image

Created: 2015-08-19 0:51:59 UTC

Image Type: MIPS Linux Kernel Image (lzma compressed)

Data Size: 1087594 Bytes = 1 MB

Load Address: 80000000

Entry Point: 80000000

raspi_read: from:50040 len:10986a

................. Verifying Checksum ... OK

Uncompressing Kernel Image ... OK

No initrd

## Transferring control to Linux (at address 80000000) ...

## Giving linux memsize in MB, 32

Starting kernel ...

[ 0.000000] Linux version 3.18.20 (chenqy@smarthome) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46682) ) #5 Wed Aug 19 08:51:09 CST 2015

[ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3

[ 0.000000] bootconsole [early0] enabled

[ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)

[ 0.000000] MIPS: machine is HAME MPR-A1

[ 0.000000] Determined physical RAM map:

[ 0.000000] memory: 02000000 @ 00000000 (usable)

[ 0.000000] Initrd not found or empty - disabling initrd

[ 0.000000] Zone ranges:

[ 0.000000] Normal [mem 0x00000000-0x01ffffff]

[ 0.000000] Movable zone start for each node

[ 0.000000] Early memory node ranges

[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]

[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]

[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.

[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128

[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2

[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)

[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.000000] Writing ErrCtl register=000008f0

[ 0.000000] Readback ErrCtl register=000008f0

[ 0.000000] Memory: 29016K/32768K available (2410K kernel code, 122K rwdata, 480K rodata, 180K init, 181K bss, 3752K reserved)

[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

[ 0.000000] NR_IRQS:256

[ 0.000000] CPU Clock: 360MHz

[ 0.000000] systick: running - mult: 214748, shift: 32

[ 0.010000] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)

[ 0.080000] pid_max: default: 32768 minimum: 301

[ 0.090000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.100000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.110000] pinctrl core: initialized pinctrl subsystem

[ 0.120000] NET: Registered protocol family 16

[ 0.130000] rt2880-pinmux pinctrl: invalid group "rgmii" for function "gpio"

[ 0.140000] rt2880-pinmux pinctrl: invalid group "mdio" for function "gpio"

[ 0.180000] rt2880_gpio 10000600.gpio: registering 22 gpios

[ 0.190000] rt2880_gpio 10000600.gpio: registering 22 irq handlers

[ 0.200000] rt2880_gpio 10000660.gpio: registering 6 gpios

[ 0.210000] rt2880_gpio 10000660.gpio: registering 6 irq handlers

[ 0.220000] Switched to clocksource systick

[ 0.230000] NET: Registered protocol family 2

[ 0.240000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.250000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)

[ 0.260000] TCP: Hash tables configured (established 1024 bind 1024)

[ 0.280000] TCP: reno registered

[ 0.280000] UDP hash table entries: 256 (order: 0, 4096 bytes)

[ 0.290000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)

[ 0.310000] NET: Registered protocol family 1

[ 0.320000] rt-timer 10000100.timer: maximum frequency is 7324Hz

[ 0.330000] futex hash table entries: 256 (order: -1, 3072 bytes)

[ 0.360000] squashfs: version 4.0 (2009/01/31) Phillip Lougher

[ 0.390000] msgmni has been set to 56

[ 0.430000] io scheduler noop registered

[ 0.440000] io scheduler deadline registered (default)

[ 0.450000] gpio-export gpio_export: 2 gpio(s) exported

[ 0.470000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled

[ 0.480000] console [ttyS0] disabled

[ 0.490000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A

[ 0.510000] console [ttyS0] enabled

[ 0.520000] bootconsole [early0] disabled

[ 0.550000] m25p80 spi32766.0: found mx25l3205d, expected s25fl064k

[ 0.560000] m25p80 spi32766.0: mx25l3205d (4096 Kbytes)

[ 0.570000] 4 ofpart partitions found on MTD device spi32766.0

[ 0.590000] Creating 4 MTD partitions on "spi32766.0":

[ 0.600000] 0x000000000000-0x000000030000 : "u-boot"

[ 0.610000] 0x000000030000-0x000000040000 : "u-boot-env"

[ 0.620000] 0x000000040000-0x000000050000 : "factory"

[ 0.630000] 0x000000050000-0x000000400000 : "firmware"

[ 0.690000] 2 uimage-fw partitions found on MTD device firmware

[ 0.700000] 0x000000050000-0x0000001598aa : "kernel"

[ 0.710000] 0x0000001598aa-0x000000400000 : "rootfs"

[ 0.720000] mtd: device 5 (rootfs) set to be root filesystem

[ 0.730000] 1 squashfs-split partitions found on MTD device rootfs

[ 0.750000] 0x0000003a0000-0x000000400000 : "rootfs_data"

[ 0.770000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5

[ 0.790000] rt2880_wdt 10000120.watchdog: Initialized

[ 0.800000] TCP: cubic registered

[ 0.810000] NET: Registered protocol family 17

[ 0.820000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.

[ 0.840000] 8021q: 802.1Q VLAN Support v1.8

[ 0.870000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.

[ 0.890000] Freeing unused kernel memory: 180K (802f3000 - 80320000)

[ 4.430000] init: Console is alive

[ 4.440000] init: - watchdog -

[ 7.320000] usbcore: registered new interface driver usbfs

[ 7.330000] usbcore: registered new interface driver hub

[ 7.340000] usbcore: registered new device driver usb

[ 7.360000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[ 7.370000] ehci-platform: EHCI generic platform driver

[ 7.590000] phy phy-usbphy.0: remote usb device wakeup disabled

[ 7.600000] phy phy-usbphy.0: UTMI 16bit 30MHz

[ 7.610000] ehci-platform 101c0000.ehci: EHCI Host Controller

[ 7.620000] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1

[ 7.630000] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000

[ 7.670000] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00

[ 7.680000] hub 1-0:1.0: USB hub found

[ 7.690000] hub 1-0:1.0: 1 port detected

[ 7.700000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

[ 7.720000] ohci-platform: OHCI generic platform driver

[ 7.730000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller

[ 7.740000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2

[ 7.760000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000

[ 7.830000] hub 2-0:1.0: USB hub found

[ 7.840000] hub 2-0:1.0: 1 port detected

[ 8.650000] init: - preinit -

[ 10.240000] rt305x-esw 10110000.esw: link changed 0x00

[ 10.580000] random: procd urandom read with 16 bits of entropy available

Press the [f] key and hit [enter] to enter failsafe mode

Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level

[ 12.030000] rt305x-esw 10110000.esw: link changed 0x10

[ 13.950000] mount_root: jffs2 not ready yet, using temporary tmpfs overlay

[ 14.000000] procd: - early -

[ 14.010000] procd: - watchdog -

[ 14.950000] procd: - ubus -

[ 15.970000] procd: - init -

Please press Enter to activate this console.

[ 17.350000] NET: Registered protocol family 10

[ 17.410000] Loading modules backported from Linux version master-2015-07-21-0-g47cd203

[ 17.430000] Backport generated by backports.git backports-20150626-0-gc1a4168

[ 17.480000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)

[ 17.560000] xt_time: kernel timezone is -0000

[ 17.630000] cfg80211: World regulatory domain updated:

[ 17.640000] cfg80211: DFS Master region: unset

[ 17.650000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)

[ 17.670000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)

[ 17.680000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)

[ 17.700000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)

[ 17.710000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)

[ 17.730000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)

[ 17.750000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)

[ 17.770000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)

[ 17.790000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)

[ 17.930000] PPP generic driver version 2.4.2

[ 17.940000] NET: Registered protocol family 24

[ 18.000000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected

[ 18.020000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected

[ 25.010000] rt305x-esw 10110000.esw: link changed 0x00

[ 26.810000] rt305x-esw 10110000.esw: link changed 0x10

[ 29.950000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0

[ 29.980000] jffs2_build_filesystem(): unlocking the mtd device... done.

[ 29.990000] jffs2_build_filesystem(): erasing all blocks after the end marker...

[ 34.230000] device eth0.1 entered promiscuous mode

[ 34.240000] device eth0 entered promiscuous mode

[ 34.280000] br-lan: port 1(eth0.1) entered forwarding state

[ 34.290000] br-lan: port 1(eth0.1) entered forwarding state

[ 35.820000] done.

[ 35.820000] jffs2: notice: (918) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.

[ 36.290000] br-lan: port 1(eth0.1) entered forwarding state

[   41.190000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   41.210000] device wlan0 entered promiscuous mode
[   42.030000] br-lan: port 2(wlan0) entered forwarding state
[   42.040000] br-lan: port 2(wlan0) entered forwarding state
[   42.050000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   44.040000] br-lan: port 2(wlan0) entered forwarding state
[   64.700000] random: nonblocking pool is initialized

BusyBox v1.23.2 (2015-08-19 00:33:19 CST) built-in shell (ash)

_______ ________ __

| |.-----.-----.-----.| | | |.----.| |_

| - || _ | -__| || | | || _|| _|

|_______|| __|_____|__|__||________||__| |____|

|__| W I R E L E S S F R E E D O M

-----------------------------------------------------

CHAOS CALMER (Bleeding Edge, r46682)

-----------------------------------------------------

* 1 1/2 oz Gin Shake with a glassful

* 1/4 oz Triple Sec of broken ice and pour

* 3/4 oz Lime Juice unstrained into a goblet.