1、iwlist
用于对/proc/net/wireless文件进行分析,得出无线网卡相关信息
~ # iwlist --help
Usage: iwlist [interface] scanning [essid NNN] [last]
[interface] frequency
[interface] channel
[interface] bitrate
[interface] rate
[interface] encryption
[interface] keys
[interface] power
[interface] txpower
[interface] retry
[interface] ap
[interface] accesspoints
[interface] peers
[interface] event
[interface] auth
[interface] wpakeys
[interface] genie
[interface] modulation
# iwlist wlan0 scanning 搜索当前无线网络
# iwlist wlan0 frequen 显示频道信息
# iwlist wlan0 rate 显示连接速度
# iwlist wlan0 power 显示电源模式
# iwlist wlan0 txpower 显示功耗
# iwlist wlan0 retry 显示重试连接次数(网络不稳定查看)
# iwlist wlan0 ap 显示热点信息
# iwlist --help 显示帮助信息
# iwlist --version 显示版本信息
2、iwconfig
系统配置无线网络设备或显示无线网络设备信息。iwconfig 命令类似于ifconfig命令,但是他配置对象是无线网卡,它对网络设备进行无线操作,如设置无线通信频段
~ # iwconfig --help
Usage: iwconfig [interface]
interface essid {NNN|any|on|off}
interface mode {managed|ad-hoc|master|...}
interface freq N.NNN[k|M|G]
interface channel N
interface bit {N[k|M|G]|auto|fixed}
interface rate {N[k|M|G]|auto|fixed}
interface enc {NNNN-NNNN|off}
interface key {NNNN-NNNN|off}
interface power {period N|timeout N|saving N|off}
interface nickname NNN
interface nwid {NN|on|off}
interface ap {N|off|auto}
interface txpower {NmW|NdBm|off|auto}
interface sens N
interface retry {limit N|lifetime N}
interface rts {N|auto|fixed|off}
interface frag {N|auto|fixed|off}
interface modulation {11g|11a|CCK|OFDMg|...}
interface commit
auto 自动模式
essid 设置ESSID
nwid 设置网络ID
freq 设置无线网络通信频段
chanel 设置无线网络通信频段
sens 设置无线网络设备的感知阀值
mode 设置无线网络设备的通信设备
ap 强迫无线网卡向给定地址的接入点注册
nick<名字> 为网卡设定别名
rate<速率> 设定无线网卡的速率
rts<阀值> 在传输数据包之前增加一次握手,确信信道在正常的
power 无线网卡的功率设置
3、iw
iw是一种新的基于 nl80211 的用于无线设备的CLI配置实用程序。它支持最近已添加到内核所有新的驱动程序。采用无线扩展接口的旧工具iwconfig已被废弃,强烈建议切换到 iw 和 nl80211。Linux内核的其余部分,iw 仍处于开发阶段。功能被随时添加。 iw 的唯一文档就是此页和“iw help”的输出。 请帮助扩大这个页面。
有一个页面列出iwconfig和iw的用例:替换 iwconfig.
# iw help # 帮助
# iw list # 获得所有设备的功能,如带宽信息(2.4GHz,和5GHz),和802.11n的信息
# iw dev wlan0 scan # 扫描
# iw event # 监听事件
# iw dev wlan0 link # 获得链路状态
# iw wlan0 connect foo # 连接到已禁用加密的AP,这里它的SSID是foo
# iw wlan0 connect foo 2432 # 假设你有两个AP SSID 都是 foo ,你知道你要连接的是在 2432 频道
# iw wlan0 connect foo keys 0:abcde d:1:0011223344 # 连接到使用WEP的AP
# iw dev wlan1 station dump # 获取station 的统计信息
# iw dev wlan1 station get # 获得station对应的peer统计信息
# iw wlan0 set bitrates legacy-2.4 12 18 24 # 修改传输比特率
# iw dev wlan0 set bitrates mcs-5 4 # 修改tx HT MCS的比特率
# iw dev wlan0 set bitrates mcs-2.4 10
# iw dev wlan0 set bitrates mcs-5 # 清除所有 tx 比特率和设置的东西来恢复正常
# iw dev set txpower [] #设置传输功率
# iw phy set txpower [] #设置传输功率
# iw dev wlan0 set power_save on #设置省电模式
# iw dev wlan0 get power_save #查询当前的节电设定
# iw phy phy0 interface add moni0 type monitor #添加一个 monitor 接口
4、wpa_supplicant
wpa_supplicant 是跨平台的 WPA 请求者程序(supplicant),支持 WEP、WPA 和 WPA2(IEEE 802.11i / RSN )。
可以在桌面、笔记本甚至嵌入式系统中使用。
连接到加密无线网络的第一步是让 wpa_supplicant 获取 WPA 认证者的认证。为此, wpa_supplicant 必须进行配置以使其能够向认证者提交认证信息。一旦完成认证,就可以正常连接网络,并通过 iproute2 手工获取 IP 地址;或者使用 systemd-networkd 或 dhcpcd之类的网络管理程序,通过配置一个接口然后通过 DHCP 自动获取 IP 地址。
发现了什么?sta使用iwconfig命令只能连接无密码的AP热点,要连接使用WEP、WPA等加密的AP,就需要借助wpa_supplicant!
当然,wpa_supplicant也有其他功能:
usage:
wpa_supplicant [-BddhKLqqstuvW] [-P<pid file>] [-g<global ctrl>] \
-i<ifname> -c<config file> [-C<ctrl>] [-D<driver>] [-p<driver_param>] \
[-b<br_ifname>] [-f<debug file>] [-e<entropy file>] \
[-o<override driver>] [-O<override ctrl>] \
[-N -i<ifname> -c<conf> [-C<ctrl>] [-D<driver>] \
[-p<driver_param>] [-b<br_ifname>] ...]
drivers:
athr = Atheros Linux driver
options:
-b = optional bridge interface name
-B = run daemon in the background
-c = Configuration file
-C = ctrl_interface parameter (only used if -c is not)
-i = interface name
-d = increase debugging verbosity (-dd even more)
-D = driver name (can be multiple drivers: nl80211,wext)
-e = entropy file
-g = global ctrl_interface
-K = include keys (passwords, etc.) in debug output
-t = include timestamp in debug messages
-h = show this help text
-L = show license (BSD)
-o = override driver parameter for new interfaces
-O = override ctrl_interface parameter for new interfaces
-p = driver parameters
-P = PID file
-q = decrease debugging verbosity (-qq even less)
-v = show version
-W = wait for a control interface monitor before starting
-N = start describing new interface
example:
wpa_supplicant -Dwext -iwlan0 -c/etc/wpa_supplicant.conf