RIP配置 华为ENSP

实验4-6 RIP配置
一、 实验背景
二、 实验目的
（1） 验证RIP创建动态路由的过程；
（2） 验证直连路由和RIP之间的关系；
（3） 了解动态路由和静态路由的差别
（4） 验证动态路由的自适应性。
三、 实验设备
路由器AR1220两台，交换机S5700六台，PC六台。
四、 实验步骤
1、 新建拓扑图

2、 PC配置IP地址、子网掩码、网关
如上图
3、 路由器AR1配置

system-view
[Huawei]sysn AR1
[AR1]undo info-center enable
[AR1]interface GigabitEthernet 0/0/0
[AR1-GigabitEthernet0/0/0]ip address 192.168.1.254 24
[AR1-GigabitEthernet0/0/0]quit
[AR1]interface GigabitEthernet 0/0/1
[AR1-GigabitEthernet0/0/1]ip address 192.168.5.1 24
[AR1-GigabitEthernet0/0/1]quit
[AR1]interface GigabitEthernet 2/0/0
[AR1-GigabitEthernet2/0/0]ip address 192.168.6.1 24
[AR1-GigabitEthernet2/0/0]quit
[AR1]rip
[AR1-rip-1]version 2
[AR1-rip-1]undo summary
[AR1-rip-1]network 192.168.1.0
[AR1-rip-1]network 192.168.5.0
[AR1-rip-1]network 192.168.6.0
[AR1-rip-1]quit
4、 路由器AR2配置
system-view
[Huawei]sysn AR2
[AR2]undo info-center enable
[AR2]interface GigabitEthernet 0/0/0
[AR2-GigabitEthernet0/0/0]ip address 192.168.5.2 24
[AR2-GigabitEthernet0/0/0]quit
[AR2]interface GigabitEthernet 0/0/1
[AR2-GigabitEthernet0/0/1]ip address 192.168.3.254 24
[AR2-GigabitEthernet0/0/1]quit
[AR2]interface GigabitEthernet 2/0/0
[AR2-GigabitEthernet2/0/0]ip address 192.168.8.1 24
[AR2-GigabitEthernet2/0/0]quit
[AR2]rip
[AR2-rip-1]version 2
[AR2-rip-1]undo summary
[AR2-rip-1]network 192.168.3.0
[AR2-rip-1]network 192.168.5.0
[AR2-rip-1]network 192.168.8.0
[AR2-rip-1]quit

5、 路由器AR3配置
system-view
[Huawei]sysn AR3
[AR3]undo info-center enable
[AR3]interface GigabitEthernet 0/0/0
[AR3-GigabitEthernet0/0/0]ip address 192.168.2.254 24
[AR3-GigabitEthernet0/0/0]quit
[AR3]interface GigabitEthernet 0/0/1
[AR3-GigabitEthernet0/0/1]ip address 192.168.7.1 24
[AR3-GigabitEthernet0/0/1]quit
[AR3]interface GigabitEthernet 2/0/0
[AR3-GigabitEthernet2/0/0]ip address 192.168.6.2 24
[AR3-GigabitEthernet2/0/0]quit
[AR3]rip
[AR3-rip-1]version 2
[AR3-rip-1]undo summary
[AR3-rip-1]network 192.168.2.0
[AR3-rip-1]network 192.168.6.0
[AR3-rip-1]network 192.168.7.0
[AR3-rip-1]quit

6、 路由器AR4配置
system-view
[Huawei]sysn AR4
[AR4]undo info-center enable
[AR4]interface GigabitEthernet 0/0/0
[AR4-GigabitEthernet0/0/0]ip address 192.168.7.2 24
[AR4-GigabitEthernet0/0/0]quit
[AR4]interface GigabitEthernet 0/0/1
[AR4-GigabitEthernet0/0/1]ip address 192.168.4.254 24
[AR4-GigabitEthernet0/0/1]quit
[AR4]interface GigabitEthernet 2/0/0
[AR4-GigabitEthernet2/0/0]ip address 192.168.8.2 24
[AR4-GigabitEthernet2/0/0]quit
[AR4]rip
[AR4-rip-1]version 2
[AR4-rip-1]undo summary
[AR4-rip-1]network 192.168.7.0
[AR4-rip-1]network 192.168.8.0
[AR4-rip-1]network 192.168.4.0
[AR4-rip-1]quit

1、 通过ping检测网络连通性
通过PC1去ping检测与所有PC的网络连通情况

注意：如果以上ping结果显示PC1与所有PC可以通信，，则说明已经达到了实验结果要求。

2、 保存实验配置
AR1配置：
save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
这个时候，输入y，确认保存配置
AR2配置：
save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
这个时候，输入y，确认保存配置
AR3配置：
save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
这个时候，输入y，确认保存配置
AR4配置：
save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
这个时候，输入y，确认保存配置

最后，保存实验设计文件

五、 实验总结