【011】基于51单片机的低频信号发生proteus仿真与实物设计

​一、资料内容

• （1）、基于51单片机的低频信号发生proteus仿真设计一份；
• （2）、基于51单片机的低频信号发生proteus仿真设计keli源代码一份；
• （3）、基于51单片机的低频信号发生Altium designer 原理图一份；
• （4）、基于51单片机的低频信号发生Altium designer PCB一份；
• （5）、基于51单片机的低频信号发生proteus仿真设计视频讲解一份;

二、设计要求

• （1）、本次电子实训课程要求以STC89C51系列单片机作为主控制芯片，设计一款低频信号发生器；
• （2）、系统能够实现通过按键调节多种波形的变换；
• （3）、系统能够通过按键调节波形的频率；
• （4）、波形名称以及频率可以通过LCD1602显示；’

三、相关资料截图

图1. 系统proteus仿真界面截图

图2. 系统Keil编程界面源代码截图

图3. 系统Altium designer 原理图

图4. 系统Altium designer PCB图

四、视频讲解

获取全部内容 

部分源代码：

#include<reg52.h>					   //包含头文件
#include<intrins.h>
#define uchar unsigned char			   //宏定义
#define uint unsigned int

sbit s1=P3^5; 						   //定义按键的接口	   原理图中为TAP2
sbit s2=P3^6;						   //  原理图中为TAP3
sbit s3=P3^7;						   //  原理图中为TAP4
									   
sbit lcdrs=P1^0;					   //液晶控制位
sbit lcden=P1^1;


sbit csda=P3^3;						   //DA控制位
sbit wr=P3^4;

char num,boxing,u;					   //定义全局变量
uint pinlv;
uchar code table[]="0123456789";		//定义显示的数组
uchar code table1[]="frequence:boxing:";
uchar code sin[64]={
135,145,158,167,176,188,199,209,218,226,234,240,245,249,252,254,254,253,251,247,243,237,230,222,213,204,193,182,170,158,
146,133,121,108,96,84,72,61,50,41,32,24,17,11,7,3,1,0,0,2,5,9,14,20,28,36,45,55,66,78,90,102,114,128
};					  //正弦波取码
uchar code juxing[64]={
255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,
255,255,255,255,255,255,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
};					  //矩形波取码
uchar code juchi[64]={
0,4,8,12,16,20,24,28,32,36,40,45,49,53,57,61,65,69,73,77,81,85,89,93,97,101,105,109,113,117,121,125,130,134,138,142,
146,150,154,158,162,166,170,174,178,182,186,190,194,198,202,206,210,215,219,223,227,231,235,239,243,247,251,255
};					  //锯齿波取码
uchar code tixing[64]={
0,13,26,39,52,65,78,91,104,117,130,143,156,169,182,195,208,221,234,247,247,247,247,247,247,247,247,247,247,247,247,247,247,247,247,247,247,247,
247,247,247,247,247,247,247,242,229,216,203,190,177,164,151,138,125,112,99,86,73,60,47,34,21,8
};					   //梯形波取码
uchar code sanjiao[64]={
0,8,16,24,32,40,48,56,64,72,80,88,96,104,112,120,128,136,144,152,160,168,176,184,192,200,208,216,224,232,240,248,
248,240,232,224,216,208,200,192,184,176,168,160,152,144,136,128,120,112,104,96,88,80,72,64,56,48,40,32,24,16,8,0
};						//三角波取码


void delay(uint xms)	 //延时函数
{
	int a,b;
	for(a=xms;a>0;a--)
		for(b=110;b>0;b--);
}
void write_com(uchar com)		//LCD1602写命令函数
{
	lcdrs=0;
	P0=com;	
	delay(1);
	lcden=1;
	delay(1);						 			  
	lcden=0;
}

void write_date(uchar date)		//LCD1602写数据函数
{
	lcdrs=1;
	P0=date;
	delay(1);
	lcden=1;
	delay(1);
	lcden=0;
}